#1 Le 20/05/2019, à 09:27
- winux
[RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Bonjour
J'explicite un peu le titre
Je suis en double boot : Ubuntu 18.04.2 et W10
je démarre parfois sur W10, pour mes présentations Power Point car LO Impress les lit très mal
une fois terminé, je repars sur mon préféré Ubuntu et je constate alors que :
le temps écoulé entre le login et l'affichage du bureau est très long
je reste sur un écran gris alors que je n'ai pas ça si reboot depuis ubuntu.
C'est uniquement après reboot depuis W10.
Suite aux lenteurs que j'ai évoquées jadis sur Lubuntu d'un autre PC (résolues par le forum) et les posts récents que je viens de parcourir sur le sujet, voici quelques retours qui pourraient peut-être aider. Merci pour votre aide
gerard@PC4:~$ sudo systemd-analyze
[sudo] Mot de passe de gerard :
Startup finished in 4.208s (kernel) + 8.835s (userspace) = 13.043s
graphical.target reached after 8.828s in userspace gerard@PC4:~$ sudo systemd-analyze blame
[sudo] Mot de passe de gerard :
4.891s plymouth-quit-wait.service
2.014s postfix@-.service
1.226s dev-sda2.device
1.051s networking.service
822ms fwupd.service
814ms systemd-journal-flush.service
686ms snapd.service
445ms udisks2.service
380ms NetworkManager.service
375ms media-BACKUP.mount
371ms systemd-logind.service
329ms snap-gnome\x2dlogs-61.mount
303ms snap-gnome\x2d3\x2d28\x2d1804-40.mount
287ms dev-loop8.device
281ms dev-loop12.device
274ms dev-loop11.device
273ms systemd-resolved.service
273ms dev-loop13.device
272ms dev-loop10.device
272ms systemd-timesyncd.service
260ms dev-loop9.device
260ms media-DATA\x2dGG.mount
257ms networkd-dispatcher.servicegerard@PC4:~$ lscpu
Architecture : x86_64
Mode(s) opératoire(s) des processeurs : 32-bit, 64-bit
Boutisme : Little Endian
Processeur(s) : 4
Liste de processeur(s) en ligne : 0-3
Thread(s) par cœur : 1
Cœur(s) par socket : 4
Socket(s) : 1
Nœud(s) NUMA : 1
Identifiant constructeur : GenuineIntel
Famille de processeur : 6
Modèle : 42
Nom de modèle : Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz
Révision : 7
Vitesse du processeur en MHz : 1754.059
Vitesse maximale du processeur en MHz : 3700,0000
Vitesse minimale du processeur en MHz : 1600,0000
BogoMIPS : 6584.83
Virtualisation : VT-x
Cache L1d : 32K
Cache L1i : 32K
Cache L2 : 256K
Cache L3 : 6144K
Nœud NUMA 0 de processeur(s) : 0-3
Drapaux : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx lahf_lm epb pti ssbd ibrs ibpb stibp tpr_shadow vnmi flexpriority ept vpid xsaveopt dtherm ida arat pln pts md_clear flush_l1d
gerard@PC4:~$ free -m
total utilisé libre partagé tamp/cache disponible
Mem: 3927 1674 1076 55 1176 1971
Partition d'échange: 3999 0 3999 gerard@PC4:~$ top
top - 09:07:02 up 49 min, 1 user, load average: 0,00, 0,08, 0,16
Tâches: 274 total, 2 en cours, 222 en veille, 0 arrêté, 0 zombie
%Cpu(s): 3,6 ut, 3,6 sy, 0,0 ni, 92,8 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1100276 libr, 1725160 util, 1196784 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2017332 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1537 root 20 0 0 0 0 I 9,5 0,0 0:21.10 kworker/u16:1-e
1679 gerard 20 0 3844180 228368 86952 R 9,5 5,7 0:43.92 gnome-shell
2761 gerard 20 0 731552 41308 28288 S 4,8 1,0 0:01.32 gnome-terminal-
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.50 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd
3 root 0 -20 0 0 0 I 0,0 0,0 0:00.00 rcu_gp top - 09:07:02 up 49 min, 1 user, load average: 0,00, 0,08, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 28,6 ut, 14,3 sy, 0,0 ni, 57,1 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1100276 libr, 1725160 util, 1196784 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2017332 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1679 gerard 20 0 3845164 228400 86952 R 200,0 5,7 0:43.93 gnome-shell
3394 gerard 20 0 51436 4248 3540 R 100,0 0,1 0:00.15 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.50 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd
3 root 0 -20 0 0 0 I 0,0 0,0 0:00.00 rcu_gp
4 root 0 -20 0 0 0 I 0,0 0,0 0:00.00 rcu_par_gp top - 09:07:03 up 49 min, 1 user, load average: 0,00, 0,08, 0,16
Tâches: 274 total, 2 en cours, 222 en veille, 0 arrêté, 0 zombie
%Cpu(s): 2,5 ut, 6,3 sy, 0,0 ni, 91,1 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098636 libr, 1726344 util, 1197240 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015700 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1537 root 20 0 0 0 0 I 15,0 0,0 0:21.13 kworker/u16:1-e
1564 gerard 20 0 521724 72840 55840 S 10,0 1,8 0:28.64 Xorg
1679 gerard 20 0 3844668 228400 86952 R 10,0 5,7 0:43.95 gnome-shell
3394 gerard 20 0 51436 4248 3540 R 5,0 0,1 0:00.16 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.50 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd top - 09:07:03 up 49 min, 1 user, load average: 0,00, 0,08, 0,16
Tâches: 274 total, 3 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 33,3 ut, 16,7 sy, 0,0 ni, 50,0 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098636 libr, 1726344 util, 1197240 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015700 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1679 gerard 20 0 3845148 228400 86952 R 50,0 5,7 0:43.96 gnome-shell
2761 gerard 20 0 731744 41308 28288 S 50,0 1,0 0:01.33 gnome-terminal-
3394 gerard 20 0 51436 4248 3540 R 50,0 0,1 0:00.17 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.50 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd
3 root 0 -20 0 0 0 I 0,0 0,0 0:00.00 rcu_gp top - 09:07:03 up 49 min, 1 user, load average: 0,00, 0,08, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 16,7 ut, 16,7 sy, 0,0 ni, 66,7 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098636 libr, 1726344 util, 1197240 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015700 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1679 gerard 20 0 3844180 228400 86952 S 66,7 5,7 0:43.98 gnome-shell
1564 gerard 20 0 521720 72840 55840 D 33,3 1,8 0:28.65 Xorg
3394 gerard 20 0 51436 4248 3540 R 33,3 0,1 0:00.18 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.50 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd
3 root 0 -20 0 0 0 I 0,0 0,0 0:00.00 rcu_gp top - 09:07:03 up 49 min, 1 user, load average: 0,00, 0,08, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 28,6 ut, 14,3 sy, 0,0 ni, 57,1 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098636 libr, 1726344 util, 1197240 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015700 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1537 root 20 0 0 0 0 R 50,0 0,0 0:21.14 kworker/u16:1+e
1564 gerard 20 0 521724 72840 55840 S 50,0 1,8 0:28.66 Xorg
1679 gerard 20 0 3845132 228400 86952 S 50,0 5,7 0:43.99 gnome-shell
1705 root 20 0 0 0 0 I 50,0 0,0 0:00.28 kworker/1:1-eve
3394 gerard 20 0 51436 4248 3540 R 50,0 0,1 0:00.19 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.50 systemd top - 09:07:42 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 1 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 0,9 ut, 1,9 sy, 0,0 ni, 97,1 id, 0,0 wa, 0,0 hi, 0,1 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1537 root 20 0 0 0 0 I 7,6 0,0 0:22.66 kworker/u16:1-e
1679 gerard 20 0 3844324 228100 86952 S 4,3 5,7 0:44.62 gnome-shell
1564 gerard 20 0 521716 72840 55840 S 2,3 1,8 0:29.00 Xorg
2761 gerard 20 0 732000 41308 28288 S 0,7 1,0 0:01.53 gnome-terminal-
10 root 20 0 0 0 0 I 0,3 0,0 0:00.31 rcu_sched
2831 gerard 20 0 3182032 282056 126688 S 0,3 7,0 0:09.98 chromium-browse
top - 09:07:42 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 2,3 ut, 1,7 sy, 0,0 ni, 96,0 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1564 gerard 20 0 521796 72840 55840 D 4,4 1,8 0:29.02 Xorg
1679 gerard 20 0 3844316 228116 86952 S 4,4 5,7 0:44.64 gnome-shell
1537 root 20 0 0 0 0 D 2,2 0,0 0:22.67 kworker/u16:1+e
1720 gerard 20 0 435676 8296 6800 S 2,2 0,2 0:01.47 ibus-daemon
3394 gerard 20 0 51436 4248 3540 R 2,2 0,1 0:00.38 top
1 root 20 0 225584 9552 6832 R 0,0 0,2 0:01.51 systemd top - 09:07:42 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 10,7 ut, 10,7 sy, 0,0 ni, 75,0 id, 0,0 wa, 0,0 hi, 3,6 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1679 gerard 20 0 3844732 228136 86952 R 42,9 5,7 0:44.67 gnome-shell
1537 root 20 0 0 0 0 D 28,6 0,0 0:22.69 kworker/u16:1+e
2761 gerard 20 0 731680 41404 28288 S 14,3 1,0 0:01.54 gnome-terminal-
3394 gerard 20 0 51436 4248 3540 R 14,3 0,1 0:00.39 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.51 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd
top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 3 en cours, 222 en veille, 0 arrêté, 0 zombie
%Cpu(s): 12,5 ut, 18,8 sy, 0,0 ni, 68,8 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1537 root 20 0 0 0 0 D 25,0 0,0 0:22.70 kworker/u16:1+e
1679 gerard 20 0 3844728 228148 86952 R 25,0 5,7 0:44.68 gnome-shell
3394 gerard 20 0 51436 4248 3540 R 25,0 0,1 0:00.40 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.51 systemd
top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 22,2 ut, 33,3 sy, 0,0 ni, 44,4 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1564 gerard 20 0 521720 72840 55840 S 100,0 1,8 0:29.04 Xorg
1679 gerard 20 0 3845036 228164 86952 S 50,0 5,7 0:44.69 gnome-shell
3394 gerard 20 0 51436 4248 3540 R 50,0 0,1 0:00.41 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.51 systemd top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 28,6 ut, 14,3 sy, 0,0 ni, 57,1 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1679 gerard 20 0 3844660 228168 86952 R 200,0 5,7 0:44.70 gnome-shell
3394 gerard 20 0 51436 4248 3540 R 100,0 0,1 0:00.42 top
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.51 systemd top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 1 en cours, 224 en veille, 0 arrêté, 0 zombie
top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 2 en cours, 223 en veille, 0 arrêté, 0 zombie
%Cpu(s): 16,7 ut, 8,3 sy, 0,0 ni, 75,0 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1564 gerard 20 0 521716 72840 55840 D 66,7 1,8 0:29.07 Xorg top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 1 en cours, 224 en veille, 0 arrêté, 0 zombie
top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 4 en cours, 221 en veille, 0 arrêté, 0 zombie
%Cpu(s): 16,7 ut, 16,7 sy, 0,0 ni, 66,7 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1705 root 20 0 0 0 0 I 50,0 0,0 0:00.29 kworker/1:1-eve top - 09:07:43 up 50 min, 1 user, load average: 0,14, 0,10, 0,16
Tâches: 274 total, 2 en cours, 222 en veille, 0 arrêté, 0 zombie
%Cpu(s): 30,0 ut, 10,0 sy, 0,0 ni, 60,0 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1098824 libr, 1726524 util, 1196872 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 2015960 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM. top - 09:23:39 up 1:06, 1 user, load average: 0,22, 0,17, 0,16
Tâches: 266 total, 1 en cours, 217 en veille, 0 arrêté, 0 zombie
%Cpu(s): 0,2 ut, 0,2 sy, 0,0 ni, 99,6 id, 0,0 wa, 0,0 hi, 0,0 si, 0,0 st
KiB Mem : 4022220 total, 1077472 libr, 1755660 util, 1189088 tamp/cache
KiB Éch: 4095996 total, 4095996 libr, 0 util. 1997656 dispo Mem
PID UTIL. PR NI VIRT RES SHR S %CPU %MEM TEMPS+ COM.
1679 gerard 20 0 3844296 229404 86968 S 1,0 5,7 1:23.61 gnome-shell
3321 root 20 0 0 0 0 I 0,7 0,0 0:14.01 kworker/u16:2-e
1564 gerard 20 0 521704 72880 55880 S 0,3 1,8 0:46.82 Xorg
2761 gerard 20 0 734080 42048 28876 S 0,3 1,0 0:02.84 gnome-terminal-
1 root 20 0 225584 9552 6832 S 0,0 0,2 0:01.87 systemd
2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd Dernière modification par winux (Le 21/05/2019, à 20:21)
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#2 Le 20/05/2019, à 11:11
- kholo
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
salut,
manque peut être un
dmesgvoire
dmesg | grep -i failqui sera plus verbeux sur les erreurs
... après un reboot depuis Doz bien sur !
Hors ligne
#3 Le 20/05/2019, à 14:04
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Merci pour ta réponse Kholo
En fait chrono en main c'est à peu près pareil, ce n'était qu'une impression car 8 s ça peut paraître long quand on attend derrière un écran gris.
Bref, résultats du chrono
démarrage W10 après démarrage précédent sur Ubuntu
jusqu'au login : 1mn10
jusqu'au bureau actif : 2s
démarrage Ubuntu après démarrage précédent sur W10
jusqu'au login : 42s
jusqu'au bureau actif : 8s
démarrage Ubuntu après démarrage précédent sur Ubuntu
jusqu'au login : 40s
jusqu'au bureau actif : 8s
Néanmoins, voici le retour de tes commandes au cas où tu verrais une explication à la question, pourquoi :
démarrage login - bureau
= 2s sur W10
et 8s sur Ubuntu ?
Merci
gerard@PC4:~$ dmesg
[ 0.000000] microcode: microcode updated early to revision 0x2f, date = 2019-02-17
[ 0.000000] Linux version 4.18.0-20-generic (buildd@lcy01-amd64-020) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21~18.04.1-Ubuntu SMP Wed May 8 08:43:37 UTC 2019 (Ubuntu 4.18.0-20.21~18.04.1-generic 4.18.20)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-20-generic root=UUID=9e193abd-bd12-4800-aa6a-e92130f3ceff ro quiet splash vt.handoff=1
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009dbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000df7cffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000df7d0000-0x00000000df7d2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000df7d3000-0x00000000df7dffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000df7e0000-0x00000000df7fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011f7fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. P67A-UD3-B3/P67A-UD3-B3, BIOS F2 02/22/2011
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] last_pfn = 0x11f800 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CCFFF write-protect
[ 0.000000] CD000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 2 base 100000000 mask FE0000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] total RAM covered: 4096M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 1G num_reg: 3 lose cover RAM: 0G
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] last_pfn = 0xdf7d0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f5a20-0x000f5a2f] mapped at [(____ptrval____)]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [(____ptrval____)] 97000 size 24576
[ 0.000000] BRK [0x23b63000, 0x23b63fff] PGTABLE
[ 0.000000] BRK [0x23b64000, 0x23b64fff] PGTABLE
[ 0.000000] BRK [0x23b65000, 0x23b65fff] PGTABLE
[ 0.000000] BRK [0x23b66000, 0x23b66fff] PGTABLE
[ 0.000000] BRK [0x23b67000, 0x23b67fff] PGTABLE
[ 0.000000] BRK [0x23b68000, 0x23b68fff] PGTABLE
[ 0.000000] BRK [0x23b69000, 0x23b69fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x33465000-0x35a29fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F7180 000014 (v00 GBT )
[ 0.000000] ACPI: RSDT 0x00000000DF7D3040 00004C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: FACP 0x00000000DF7D3100 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: DSDT 0x00000000DF7D31C0 00469B (v01 GBT GBTUACPI 00001000 MSFT 04000000)
[ 0.000000] ACPI: FACS 0x00000000DF7D0000 000040
[ 0.000000] ACPI: HPET 0x00000000DF7D79C0 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
[ 0.000000] ACPI: MCFG 0x00000000DF7D7A40 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: ASPT 0x00000000DF7D7B00 000034 (v07 GBT PerfTune 312E3042 UTBG 01010101)
[ 0.000000] ACPI: SSPT 0x00000000DF7D7B40 00239C (v01 GBT SsptHead 312E3042 UTBG 01010101)
[ 0.000000] ACPI: EUDS 0x00000000DF7D9EE0 0000C0 (v01 GBT 00000000 00000000)
[ 0.000000] ACPI: MATS 0x00000000DF7D9FA0 000034 (v01 GBT 00000000 00000000)
[ 0.000000] ACPI: TAMG 0x00000000DF7DA000 000A3A (v01 GBT GBT B0 5455312E BG?? 53450101)
[ 0.000000] ACPI: APIC 0x00000000DF7D78C0 0000BC (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: SSDT 0x00000000DF7DAA40 001F4C (v01 INTEL PPM RCM 80000001 INTL 20061109)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000011f7fffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x11f7d3000-0x11f7fdfff]
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000011f7fffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000df7cffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000011f7fffff]
[ 0.000000] Reserved but unavailable: 2196 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000011f7fffff]
[ 0.000000] On node 0 totalpages: 1044332
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14240 pages used for memmap
[ 0.000000] DMA32 zone: 911312 pages, LIFO batch:31
[ 0.000000] Normal zone: 2016 pages used for memmap
[ 0.000000] Normal zone: 129024 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] dfl dfl lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf7d0000-0xdf7d2fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf7d3000-0xdf7dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf7e0000-0xdf7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf800000-0xf3ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf4000000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
[ 0.000000] [mem 0xdf800000-0xf3ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] random: get_random_bytes called from start_kernel+0x99/0x55a with crng_init=0
[ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] percpu: Embedded 46 pages/cpu @(____ptrval____) s151552 r8192 d28672 u262144
[ 0.000000] pcpu-alloc: s151552 r8192 d28672 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1027991
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-20-generic root=UUID=9e193abd-bd12-4800-aa6a-e92130f3ceff ro quiet splash vt.handoff=1
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3977280K/4177328K available (12300K kernel code, 2634K rwdata, 4384K rodata, 2460K init, 2340K bss, 200048K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Kernel/User page tables isolation: enabled
[ 0.000000] ftrace: allocating 40847 entries in 160 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS: 524544, nr_irqs: 488, preallocated irqs: 16
[ 0.000000] vt handoff: transparent VT on vt#1
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] ACPI: Core revision 20180531
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] APIC: Switch to symmetric I/O mode setup
[ 0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.020000] tsc: Fast TSC calibration using PIT
[ 0.024000] tsc: Detected 3292.643 MHz processor
[ 0.024000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2f762680901, max_idle_ns: 440795209131 ns
[ 0.024000] Calibrating delay loop (skipped), value calculated using timer frequency.. 6585.28 BogoMIPS (lpj=13170572)
[ 0.024000] pid_max: default: 32768 minimum: 301
[ 0.024000] Security Framework initialized
[ 0.024000] Yama: becoming mindful.
[ 0.024000] AppArmor: AppArmor initialized
[ 0.024000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.024000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.024000] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.024000] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.028108] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.028109] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.028112] mce: CPU supports 9 MCE banks
[ 0.028119] CPU0: Thermal monitoring enabled (TM1)
[ 0.028127] process: using mwait in idle threads
[ 0.028129] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.028130] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.028131] Spectre V2 : Mitigation: Full generic retpoline
[ 0.028132] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.028132] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 0.028138] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[ 0.028139] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[ 0.028162] MDS: Mitigation: Clear CPU buffers
[ 0.028233] Freeing SMP alternatives memory: 36K
[ 0.032056] TSC deadline timer enabled
[ 0.032058] smpboot: CPU0: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz (family: 0x6, model: 0x2a, stepping: 0x7)
[ 0.032135] Performance Events: PEBS fmt1+, SandyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[ 0.032152] ... version: 3
[ 0.032153] ... bit width: 48
[ 0.032153] ... generic registers: 8
[ 0.032154] ... value mask: 0000ffffffffffff
[ 0.032154] ... max period: 00007fffffffffff
[ 0.032155] ... fixed-purpose events: 3
[ 0.032155] ... event mask: 00000007000000ff
[ 0.032184] Hierarchical SRCU implementation.
[ 0.033027] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.033041] smp: Bringing up secondary CPUs ...
[ 0.033106] x86: Booting SMP configuration:
[ 0.033107] .... node #0, CPUs: #1 #2 #3
[ 0.040024] smp: Brought up 1 node, 4 CPUs
[ 0.040024] smpboot: Max logical packages: 2
[ 0.040024] smpboot: Total of 4 processors activated (26341.14 BogoMIPS)
[ 0.042097] devtmpfs: initialized
[ 0.042097] x86/mm: Memory block size: 128MB
[ 0.042097] PM: Registering ACPI NVS region [mem 0xdf7d0000-0xdf7d2fff] (12288 bytes)
[ 0.042151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.042151] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.042151] pinctrl core: initialized pinctrl subsystem
[ 0.042151] RTC time: 11:45:35, date: 05/20/19
[ 0.042151] NET: Registered protocol family 16
[ 0.042151] audit: initializing netlink subsys (disabled)
[ 0.042151] audit: type=2000 audit(1558352735.040:1): state=initialized audit_enabled=0 res=1
[ 0.042151] cpuidle: using governor ladder
[ 0.042151] cpuidle: using governor menu
[ 0.042151] ACPI: bus type PCI registered
[ 0.042151] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.042151] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[ 0.042151] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[ 0.042151] pmd_set_huge: Cannot satisfy [mem 0xf4000000-0xf4200000] with a huge-page mapping due to MTRR override.
[ 0.042151] PCI: Using configuration type 1 for base access
[ 0.042151] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[ 0.044394] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.044394] ACPI: Added _OSI(Module Device)
[ 0.044394] ACPI: Added _OSI(Processor Device)
[ 0.044394] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.044394] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.044394] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.044394] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.047242] ACPI: 2 ACPI AML tables successfully acquired and loaded
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.052812] ACPI: Interpreter enabled
[ 0.052825] ACPI: (supports S0 S3 S4 S5)
[ 0.052826] ACPI: Using IOAPIC for interrupt routing
[ 0.052844] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.052969] ACPI: Enabled 5 GPEs in block 00 to 3F
[ 0.056742] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
[ 0.056746] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.056750] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.056959] PCI host bridge to bus 0000:00
[ 0.056961] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.056962] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.056963] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.056964] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.056965] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfebfffff window]
[ 0.056967] pci_bus 0000:00: root bus resource [bus 00-3f]
[ 0.056973] pci 0000:00:00.0: [8086:0100] type 00 class 0x060000
[ 0.057052] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[ 0.057079] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.057145] pci 0000:00:01.1: [8086:0105] type 01 class 0x060400
[ 0.057170] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[ 0.057260] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.057284] pci 0000:00:16.0: reg 0x10: [mem 0xfbfff000-0xfbfff00f 64bit]
[ 0.057351] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.057430] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.057450] pci 0000:00:1a.0: reg 0x10: [mem 0xfbffe000-0xfbffe3ff]
[ 0.057528] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.057604] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.057623] pci 0000:00:1b.0: reg 0x10: [mem 0xfbff4000-0xfbff7fff 64bit]
[ 0.057691] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.057765] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.057837] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.057920] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[ 0.057998] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.058079] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[ 0.058150] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.058235] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.058255] pci 0000:00:1d.0: reg 0x10: [mem 0xfbffd000-0xfbffd3ff]
[ 0.058334] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.058406] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.058518] pci 0000:00:1f.0: [8086:1c46] type 00 class 0x060100
[ 0.058685] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.058701] pci 0000:00:1f.2: reg 0x10: [io 0xff00-0xff07]
[ 0.058707] pci 0000:00:1f.2: reg 0x14: [io 0xfe00-0xfe03]
[ 0.058714] pci 0000:00:1f.2: reg 0x18: [io 0xfd00-0xfd07]
[ 0.058720] pci 0000:00:1f.2: reg 0x1c: [io 0xfc00-0xfc03]
[ 0.058727] pci 0000:00:1f.2: reg 0x20: [io 0xfb00-0xfb1f]
[ 0.058733] pci 0000:00:1f.2: reg 0x24: [mem 0xfbffc000-0xfbffc7ff]
[ 0.058769] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.058837] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.058854] pci 0000:00:1f.3: reg 0x10: [mem 0xfbffb000-0xfbffb0ff 64bit]
[ 0.058873] pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
[ 0.058974] pci 0000:01:00.0: [10de:0de1] type 00 class 0x030000
[ 0.058988] pci 0000:01:00.0: reg 0x10: [mem 0xf9000000-0xf9ffffff]
[ 0.058996] pci 0000:01:00.0: reg 0x14: [mem 0xe0000000-0xe7ffffff 64bit pref]
[ 0.059004] pci 0000:01:00.0: reg 0x1c: [mem 0xee000000-0xefffffff 64bit pref]
[ 0.059009] pci 0000:01:00.0: reg 0x24: [io 0xef00-0xef7f]
[ 0.059015] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[ 0.059020] pci 0000:01:00.0: enabling Extended Tags
[ 0.059091] pci 0000:01:00.1: [10de:0bea] type 00 class 0x040300
[ 0.059103] pci 0000:01:00.1: reg 0x10: [mem 0xfaffc000-0xfaffffff]
[ 0.059133] pci 0000:01:00.1: enabling Extended Tags
[ 0.068023] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.068026] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.068030] pci 0000:00:01.0: bridge window [mem 0xf9000000-0xfaffffff]
[ 0.068034] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.068089] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330
[ 0.068121] pci 0000:02:00.0: reg 0x10: [mem 0xfbdfe000-0xfbdfffff 64bit]
[ 0.068192] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.080017] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 0.080022] pci 0000:00:01.1: bridge window [mem 0xfbd00000-0xfbdfffff]
[ 0.080081] pci 0000:00:1c.0: PCI bridge to [bus 03]
[ 0.080155] pci 0000:04:00.0: [10ec:8168] type 00 class 0x020000
[ 0.080188] pci 0000:04:00.0: reg 0x10: [io 0xde00-0xdeff]
[ 0.080220] pci 0000:04:00.0: reg 0x18: [mem 0xfbeff000-0xfbefffff 64bit pref]
[ 0.080240] pci 0000:04:00.0: reg 0x20: [mem 0xfbef8000-0xfbefbfff 64bit pref]
[ 0.080349] pci 0000:04:00.0: supports D1 D2
[ 0.080350] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.080440] pci 0000:00:1c.2: ASPM: current common clock configuration is broken, reconfiguring
[ 0.092027] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.092032] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.092041] pci 0000:00:1c.2: bridge window [mem 0xfbe00000-0xfbefffff 64bit pref]
[ 0.092124] pci 0000:05:00.0: [1283:8892] type 01 class 0x060400
[ 0.092286] pci 0000:05:00.0: supports D1 D2
[ 0.092287] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.092352] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.092362] pci 0000:00:1c.3: PCI bridge to [bus 05-06]
[ 0.092431] pci_bus 0000:06: extended config space not accessible
[ 0.092524] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.092575] pci_bus 0000:07: extended config space not accessible
[ 0.092621] pci 0000:00:1e.0: PCI bridge to [bus 07] (subtractive decode)
[ 0.092629] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.092630] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.092632] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.092633] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.092634] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xfebfffff window] (subtractive decode)
[ 0.093104] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 0.093162] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
[ 0.093219] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.093276] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.093332] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.093388] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.093445] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.093501] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.093741] SCSI subsystem initialized
[ 0.093751] libata version 3.00 loaded.
[ 0.093751] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[ 0.093751] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.093751] pci 0000:01:00.0: vgaarb: bridge control possible
[ 0.093751] vgaarb: loaded
[ 0.093751] ACPI: bus type USB registered
[ 0.093751] usbcore: registered new interface driver usbfs
[ 0.093751] usbcore: registered new interface driver hub
[ 0.093751] usbcore: registered new device driver usb
[ 0.093751] pps_core: LinuxPPS API ver. 1 registered
[ 0.093751] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.093751] PTP clock support registered
[ 0.093751] EDAC MC: Ver: 3.0.0
[ 0.093751] PCI: Using ACPI for IRQ routing
[ 0.093751] PCI: pci_cache_line_size set to 64 bytes
[ 0.093751] e820: reserve RAM buffer [mem 0x0009dc00-0x0009ffff]
[ 0.093751] e820: reserve RAM buffer [mem 0xdf7d0000-0xdfffffff]
[ 0.093751] e820: reserve RAM buffer [mem 0x11f800000-0x11fffffff]
[ 0.093751] NetLabel: Initializing
[ 0.093751] NetLabel: domain hash size = 128
[ 0.093751] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.093751] NetLabel: unlabeled traffic allowed by default
[ 0.093751] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.093751] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.097019] clocksource: Switched to clocksource tsc-early
[ 0.104599] VFS: Disk quotas dquot_6.6.0
[ 0.104613] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.104696] AppArmor: AppArmor Filesystem Enabled
[ 0.104719] pnp: PnP ACPI init
[ 0.104890] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 0.104891] system 00:00: [io 0x0290-0x029f] has been reserved
[ 0.104893] system 00:00: [io 0x0800-0x087f] has been reserved
[ 0.104894] system 00:00: [io 0x0290-0x0294] has been reserved
[ 0.104895] system 00:00: [io 0x0880-0x088f] has been reserved
[ 0.104900] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.104966] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.105180] system 00:02: [io 0x0400-0x04cf] has been reserved
[ 0.105181] system 00:02: [io 0x04d2-0x04ff] has been reserved
[ 0.105184] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.105213] system 00:03: [io 0x1000-0x107f] has been reserved
[ 0.105215] system 00:03: [io 0x1080-0x10ff] has been reserved
[ 0.105217] system 00:03: [io 0x1100-0x117f] has been reserved
[ 0.105218] system 00:03: [io 0x1180-0x11ff] has been reserved
[ 0.105222] system 00:03: Plug and Play ACPI device, IDs ICD0001 PNP0c02 (active)
[ 0.105409] system 00:04: [io 0x0454-0x0457] has been reserved
[ 0.105413] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.105449] system 00:05: [mem 0xf4000000-0xf7ffffff] has been reserved
[ 0.105452] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.105676] system 00:06: [mem 0x000d0a00-0x000d3fff] has been reserved
[ 0.105678] system 00:06: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.105679] system 00:06: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.105680] system 00:06: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.105682] system 00:06: [mem 0xdf7d0000-0xdf7dffff] could not be reserved
[ 0.105683] system 00:06: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.105684] system 00:06: [mem 0x00100000-0xdf7cffff] could not be reserved
[ 0.105686] system 00:06: [mem 0xdf7e0000-0xdf7fffff] has been reserved
[ 0.105687] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.105689] system 00:06: [mem 0xfed10000-0xfed1dfff] has been reserved
[ 0.105690] system 00:06: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.105691] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.105692] system 00:06: [mem 0xffb00000-0xffb7ffff] has been reserved
[ 0.105694] system 00:06: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.105695] system 00:06: [mem 0x000e0000-0x000effff] has been reserved
[ 0.105696] system 00:06: [mem 0x20000000-0x201fffff] could not be reserved
[ 0.105698] system 00:06: [mem 0x40000000-0x400fffff] could not be reserved
[ 0.105699] system 00:06: [mem 0xdf800000-0xdfffffff] could not be reserved
[ 0.105702] system 00:06: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.105707] pnp: PnP ACPI: found 7 devices
[ 0.111163] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.111180] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 03] add_size 1000
[ 0.111182] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[ 0.111184] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000 add_align 100000
[ 0.111220] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf0000000-0xf01fffff]
[ 0.111224] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf0200000-0xf03fffff 64bit pref]
[ 0.111226] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.111228] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa07ffff pref]
[ 0.111230] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.111231] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.111233] pci 0000:00:01.0: bridge window [mem 0xf9000000-0xfaffffff]
[ 0.111235] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.111237] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 0.111239] pci 0000:00:01.1: bridge window [mem 0xfbd00000-0xfbdfffff]
[ 0.111242] pci 0000:00:1c.0: PCI bridge to [bus 03]
[ 0.111244] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.111248] pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf01fffff]
[ 0.111251] pci 0000:00:1c.0: bridge window [mem 0xf0200000-0xf03fffff 64bit pref]
[ 0.111256] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.111258] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.111263] pci 0000:00:1c.2: bridge window [mem 0xfbe00000-0xfbefffff 64bit pref]
[ 0.111268] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.111291] pci 0000:00:1c.3: PCI bridge to [bus 05-06]
[ 0.111300] pci 0000:00:1e.0: PCI bridge to [bus 07]
[ 0.111310] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.111311] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.111312] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.111313] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window]
[ 0.111314] pci_bus 0000:00: resource 8 [mem 0xe0000000-0xfebfffff window]
[ 0.111315] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 0.111316] pci_bus 0000:01: resource 1 [mem 0xf9000000-0xfaffffff]
[ 0.111317] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.111319] pci_bus 0000:02: resource 1 [mem 0xfbd00000-0xfbdfffff]
[ 0.111320] pci_bus 0000:03: resource 0 [io 0x2000-0x2fff]
[ 0.111321] pci_bus 0000:03: resource 1 [mem 0xf0000000-0xf01fffff]
[ 0.111322] pci_bus 0000:03: resource 2 [mem 0xf0200000-0xf03fffff 64bit pref]
[ 0.111323] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.111324] pci_bus 0000:04: resource 2 [mem 0xfbe00000-0xfbefffff 64bit pref]
[ 0.111325] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7 window]
[ 0.111326] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff window]
[ 0.111327] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.111328] pci_bus 0000:07: resource 7 [mem 0x000c0000-0x000dffff window]
[ 0.111330] pci_bus 0000:07: resource 8 [mem 0xe0000000-0xfebfffff window]
[ 0.111391] NET: Registered protocol family 2
[ 0.111528] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.111540] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.111586] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.111640] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.111665] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.111675] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.111708] NET: Registered protocol family 1
[ 0.111712] NET: Registered protocol family 44
[ 0.132135] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x6c0 took 19933 usecs
[ 0.152127] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x6c0 took 19512 usecs
[ 0.152145] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.152149] pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
[ 0.152298] PCI: CLS 4 bytes, default 64
[ 0.152326] Unpacking initramfs...
[ 0.554240] Freeing initrd memory: 38676K
[ 0.554256] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.554257] software IO TLB [mem 0xdb7d0000-0xdf7d0000] (64MB) mapped at [(____ptrval____)-(____ptrval____)]
[ 0.554458] Scanning for low memory corruption every 60 seconds
[ 0.554975] Initialise system trusted keyrings
[ 0.554983] Key type blacklist registered
[ 0.555006] workingset: timestamp_bits=36 max_order=20 bucket_order=0
[ 0.555943] zbud: loaded
[ 0.556303] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.556426] fuse init (API version 7.27)
[ 0.556468] pstore: using deflate compression
[ 0.557227] Key type asymmetric registered
[ 0.557228] Asymmetric key parser 'x509' registered
[ 0.557254] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.557275] io scheduler noop registered
[ 0.557276] io scheduler deadline registered
[ 0.557295] io scheduler cfq registered (default)
[ 0.557491] pcieport 0000:00:1c.0: enabling device (0000 -> 0003)
[ 0.557807] shpchp 0000:05:00.0: Requesting control of SHPC hotplug via OSHP (\_SB_.PCI0.PEX3)
[ 0.557810] shpchp 0000:05:00.0: Requesting control of SHPC hotplug via OSHP (\_SB_.PCI0)
[ 0.557813] shpchp 0000:05:00.0: Cannot get control of SHPC hotplug
[ 0.557819] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.557858] vesafb: mode is 640x480x32, linelength=2560, pages=0
[ 0.557859] vesafb: scrolling: redraw
[ 0.557860] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.557867] vesafb: framebuffer at 0xef000000, mapped to 0x(____ptrval____), using 1216k, total 1216k
[ 0.557931] Console: switching to colour frame buffer device 80x30
[ 0.557939] fb0: VESA VGA frame buffer device
[ 0.557950] intel_idle: MWAIT substates: 0x1120
[ 0.557951] intel_idle: v0.4.1 model 0x2A
[ 0.558047] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.558103] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.558110] ACPI: Power Button [PWRB]
[ 0.558140] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.558168] ACPI: Power Button [PWRF]
[ 0.558898] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.560200] Linux agpgart interface v0.103
[ 0.561485] loop: module loaded
[ 0.561609] libphy: Fixed MDIO Bus: probed
[ 0.561610] tun: Universal TUN/TAP device driver, 1.6
[ 0.561630] PPP generic driver version 2.4.2
[ 0.561654] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.561656] ehci-pci: EHCI PCI platform driver
[ 0.561742] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.561747] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.561757] ehci-pci 0000:00:1a.0: debug port 2
[ 0.565663] ehci-pci 0000:00:1a.0: cache line size of 4 is not supported
[ 0.565673] ehci-pci 0000:00:1a.0: irq 18, io mem 0xfbffe000
[ 0.580049] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.580116] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 0.580119] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.580121] usb usb1: Product: EHCI Host Controller
[ 0.580124] usb usb1: Manufacturer: Linux 4.18.0-20-generic ehci_hcd
[ 0.580126] usb usb1: SerialNumber: 0000:00:1a.0
[ 0.580285] hub 1-0:1.0: USB hub found
[ 0.580292] hub 1-0:1.0: 2 ports detected
[ 0.580447] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.580450] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.580459] ehci-pci 0000:00:1d.0: debug port 2
[ 0.584339] ehci-pci 0000:00:1d.0: cache line size of 4 is not supported
[ 0.584345] ehci-pci 0000:00:1d.0: irq 23, io mem 0xfbffd000
[ 0.600049] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.600115] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 0.600118] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.600120] usb usb2: Product: EHCI Host Controller
[ 0.600122] usb usb2: Manufacturer: Linux 4.18.0-20-generic ehci_hcd
[ 0.600124] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.600285] hub 2-0:1.0: USB hub found
[ 0.600291] hub 2-0:1.0: 2 ports detected
[ 0.600372] ehci-platform: EHCI generic platform driver
[ 0.600377] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.600380] ohci-pci: OHCI PCI platform driver
[ 0.600385] ohci-platform: OHCI generic platform driver
[ 0.600389] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.600450] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 0.600453] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 0.600535] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[ 0.600667] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 0.600669] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.600670] usb usb3: Product: xHCI Host Controller
[ 0.600671] usb usb3: Manufacturer: Linux 4.18.0-20-generic xhci-hcd
[ 0.600672] usb usb3: SerialNumber: 0000:02:00.0
[ 0.600820] hub 3-0:1.0: USB hub found
[ 0.600827] hub 3-0:1.0: 2 ports detected
[ 0.600900] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 0.600902] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[ 0.600904] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 0.604018] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.604046] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.18
[ 0.604048] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.604049] usb usb4: Product: xHCI Host Controller
[ 0.604050] usb usb4: Manufacturer: Linux 4.18.0-20-generic xhci-hcd
[ 0.604051] usb usb4: SerialNumber: 0000:02:00.0
[ 0.604169] hub 4-0:1.0: USB hub found
[ 0.604183] hub 4-0:1.0: 2 ports detected
[ 0.604267] i8042: PNP: No PS/2 controller found.
[ 0.604267] i8042: Probing ports directly.
[ 0.638297] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
[ 0.638297] i8042: If AUX port is really absent please use the 'i8042.noaux' option
[ 0.892140] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.892360] mousedev: PS/2 mouse device common for all mice
[ 0.892677] rtc_cmos 00:01: RTC can wake from S4
[ 0.892801] rtc_cmos 00:01: registered as rtc0
[ 0.892820] rtc_cmos 00:01: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.892825] i2c /dev entries driver
[ 0.892828] pcie_mp2_amd: AMD(R) PCI-E MP2 Communication Driver Version: 1.0
[ 0.892867] device-mapper: uevent: version 1.0.3
[ 0.892934] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[ 0.892938] intel_pstate: Intel P-state driver initializing
[ 0.893136] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.893440] NET: Registered protocol family 10
[ 0.896679] Segment Routing with IPv6
[ 0.896693] NET: Registered protocol family 17
[ 0.896769] Key type dns_resolver registered
[ 0.897029] RAS: Correctable Errors collector initialized.
[ 0.897049] microcode: sig=0x206a7, pf=0x2, revision=0x2f
[ 0.897117] microcode: Microcode Update Driver: v2.2.
[ 0.897123] sched_clock: Marking stable (897114076, 0)->(882333260, 14780816)
[ 0.897327] registered taskstats version 1
[ 0.897336] Loading compiled-in X.509 certificates
[ 0.899246] Loaded X.509 cert 'Build time autogenerated kernel key: 377cdf01bd4aa8cd057eca9f88365c72625360bc'
[ 0.899263] zswap: loaded using pool lzo/zbud
[ 0.901820] Key type big_key registered
[ 0.901823] Key type trusted registered
[ 0.903092] Key type encrypted registered
[ 0.903093] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.903098] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[ 0.903101] ima: Allocated hash algorithm: sha1
[ 0.903113] evm: Initialising EVM extended attributes:
[ 0.903114] evm: security.selinux
[ 0.903114] evm: security.SMACK64
[ 0.903115] evm: security.SMACK64EXEC
[ 0.903115] evm: security.SMACK64TRANSMUTE
[ 0.903116] evm: security.SMACK64MMAP
[ 0.903116] evm: security.apparmor
[ 0.903116] evm: security.ima
[ 0.903117] evm: security.capability
[ 0.903117] evm: HMAC attrs: 0x1
[ 0.903360] Magic number: 3:897:782
[ 0.903388] pci 0000:00:16.0: hash matches
[ 0.903435] rtc_cmos 00:01: setting system clock to 2019-05-20 11:45:36 UTC (1558352736)
[ 0.905759] Freeing unused kernel image memory: 2460K
[ 0.928160] Write protecting the kernel read-only data: 20480k
[ 0.928680] Freeing unused kernel image memory: 2008K
[ 0.928949] Freeing unused kernel image memory: 1760K
[ 0.936622] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.936623] x86/mm: Checking user space page tables
[ 0.943620] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 0.943644] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.960032] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 0.999035] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 0.999036] ahci 0000:00:1f.2: version 3.0
[ 0.999045] r8169 0000:04:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 0.999225] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 0.999455] r8169 0000:04:00.0 eth0: RTL8168e/8111e, 1c:6f:65:d7:53:ac, XID 2c200000, IRQ 30
[ 0.999457] r8169 0000:04:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 1.012281] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 1.012284] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ems apst
[ 1.012407] r8169 0000:04:00.0 enp4s0: renamed from eth0
[ 1.076706] scsi host0: ahci
[ 1.077011] scsi host1: ahci
[ 1.077254] scsi host2: ahci
[ 1.077367] scsi host3: ahci
[ 1.077420] scsi host4: ahci
[ 1.077475] scsi host5: ahci
[ 1.077515] ata1: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc100 irq 29
[ 1.077516] ata2: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc180 irq 29
[ 1.077518] ata3: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc200 irq 29
[ 1.077519] ata4: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc280 irq 29
[ 1.077521] ata5: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc300 irq 29
[ 1.077522] ata6: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc380 irq 29
[ 1.088352] usb 1-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 1.088353] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.088626] hub 1-1:1.0: USB hub found
[ 1.088735] hub 1-1:1.0: 6 ports detected
[ 1.116832] usb 2-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 1.116833] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.117177] hub 2-1:1.0: USB hub found
[ 1.117426] hub 2-1:1.0: 8 ports detected
[ 1.376054] usb 1-1.2: new low-speed USB device number 3 using ehci-pci
[ 1.404023] usb 2-1.3: new high-speed USB device number 3 using ehci-pci
[ 1.488491] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00
[ 1.488494] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.488497] usb 1-1.2: Product: USB Optical Mouse
[ 1.488499] usb 1-1.2: Manufacturer: Logitech
[ 1.492058] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.495020] usbcore: registered new interface driver usbhid
[ 1.495020] usbhid: USB HID core driver
[ 1.496765] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C077.0001/input/input3
[ 1.496939] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1a.0-1.2/input0
[ 1.513323] usb 2-1.3: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
[ 1.513334] usb 2-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.513335] usb 2-1.3: Product: USB 2.0 Hub
[ 1.513606] hub 2-1.3:1.0: USB hub found
[ 1.513687] hub 2-1.3:1.0: 4 ports detected
[ 1.536056] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.536316] ata1.00: ATA-10: KINGSTON SA400S37240G, SBFKB1E1, max UDMA/133
[ 1.536317] ata1.00: 468862128 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 1.536655] ata1.00: configured for UDMA/133
[ 1.536833] scsi 0:0:0:0: Direct-Access ATA KINGSTON SA400S3 B1E1 PQ: 0 ANSI: 5
[ 1.537019] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.537118] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB)
[ 1.537171] sd 0:0:0:0: [sda] Write Protect is off
[ 1.537173] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.537220] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.538355] sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[ 1.538870] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.568045] usb 1-1.3: new low-speed USB device number 4 using ehci-pci
[ 1.568062] tsc: Refined TSC clocksource calibration: 3292.520 MHz
[ 1.568071] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2f75b1eac7a, max_idle_ns: 440795210882 ns
[ 1.568159] clocksource: Switched to clocksource tsc
[ 1.592016] usb 2-1.4: new high-speed USB device number 4 using ehci-pci
[ 1.682089] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00
[ 1.682092] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.682095] usb 1-1.3: Product: USB Keyboard
[ 1.682097] usb 1-1.3: Manufacturer: Logitech
[ 1.687317] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C31C.0002/input/input4
[ 1.744323] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:1a.0-1.3/input0
[ 1.750481] input: Logitech USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:046D:C31C.0003/input/input5
[ 1.808234] input: Logitech USB Keyboard System Control as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:046D:C31C.0003/input/input6
[ 1.808441] hid-generic 0003:046D:C31C.0003: input,hidraw2: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:1a.0-1.3/input1
[ 1.850994] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.328043] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.342444] ata3.00: ATA-8: WDC WD1001FAES-00W7A0, 05.01D05, max UDMA/133
[ 2.342447] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 2.344880] ata3.00: configured for UDMA/133
[ 2.345150] scsi 2:0:0:0: Direct-Access ATA WDC WD1001FAES-0 1D05 PQ: 0 ANSI: 5
[ 2.345454] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.345521] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 2.345580] sd 2:0:0:0: [sdb] Write Protect is off
[ 2.345581] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.345646] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.353289] sdb: sdb3 sdb4
[ 2.353988] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 2.820062] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.835195] ata4.00: ATAPI: PIONEER DVD-RW DVR-219L, 1.01, max UDMA/100
[ 2.853743] ata4.00: configured for UDMA/100
[ 2.886062] scsi 3:0:0:0: CD-ROM PIONEER DVD-RW DVR-219L 1.01 PQ: 0 ANSI: 5
[ 2.967528] sr 3:0:0:0: [sr0] scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.967529] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.967699] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 2.967768] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 3.444064] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.453494] ata5.00: ATA-8: WDC WD1001FAES-00W7A0, 05.01D05, max UDMA/133
[ 3.453497] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.455746] ata5.00: configured for UDMA/133
[ 3.456000] scsi 4:0:0:0: Direct-Access ATA WDC WD1001FAES-0 1D05 PQ: 0 ANSI: 5
[ 3.456336] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 3.456597] sd 4:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 3.456638] sd 4:0:0:0: [sdc] Write Protect is off
[ 3.456640] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.456695] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.490795] sdc: sdc1
[ 3.491440] sd 4:0:0:0: [sdc] Attached SCSI disk
[ 3.770902] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.797213] random: fast init done
[ 3.797220] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 3.797224] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 3.797237] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.123815] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
[ 4.128096] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.346626] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 4.364307] systemd[1]: Detected architecture x86-64.
[ 4.366389] systemd[1]: Set hostname to <PC4>.
[ 5.589743] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.589892] systemd[1]: Created slice User and Session Slice.
[ 5.589983] systemd[1]: Created slice System Slice.
[ 5.590038] systemd[1]: Listening on Syslog Socket.
[ 5.590081] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.590120] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 5.590205] systemd[1]: Listening on Journal Audit Socket.
[ 5.622485] lp: driver loaded but no devices found
[ 5.624758] ppdev: user-space parallel port driver
[ 5.624783] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 5.656895] systemd-journald[303]: Received request to flush runtime journal from PID 1
[ 6.066172] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[ 6.066173] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 6.066174] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 6.066174] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 6.070168] cryptd: max_cpu_qlen set to 1000
[ 6.102525] AVX version of gcm_enc/dec engaged.
[ 6.102526] AES CTR mode by8 optimization enabled
[ 6.120832] snd_hda_intel 0000:01:00.1: Disabling MSI
[ 6.120837] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[ 6.140044] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC889: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 6.140046] snd_hda_codec_realtek hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 6.140047] snd_hda_codec_realtek hdaudioC0D2: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 6.140048] snd_hda_codec_realtek hdaudioC0D2: mono: mono_out=0x0
[ 6.140049] snd_hda_codec_realtek hdaudioC0D2: dig-out=0x11/0x1e
[ 6.140050] snd_hda_codec_realtek hdaudioC0D2: inputs:
[ 6.140052] snd_hda_codec_realtek hdaudioC0D2: Rear Mic=0x18
[ 6.140053] snd_hda_codec_realtek hdaudioC0D2: Front Mic=0x19
[ 6.140054] snd_hda_codec_realtek hdaudioC0D2: Line=0x1a
[ 6.140055] snd_hda_codec_realtek hdaudioC0D2: CD=0x1c
[ 6.140378] checking generic (ef000000 130000) vs hw (e0000000 8000000)
[ 6.140379] checking generic (ef000000 130000) vs hw (ee000000 2000000)
[ 6.140380] fb: switching to nouveaufb from VESA VGA
[ 6.140403] Console: switching to colour dummy device 80x25
[ 6.140506] nouveau 0000:01:00.0: NVIDIA GF108 (0c1080a1)
[ 6.153629] random: crng init done
[ 6.153631] random: 7 urandom warning(s) missed due to ratelimiting
[ 6.155616] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 6.155658] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 6.155695] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 6.155732] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 6.155768] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 6.155805] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 6.155839] input: HDA Intel PCH Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 6.237594] gpio_ich: GPIO from 436 to 511 on gpio_ich
[ 6.271786] nouveau 0000:01:00.0: bios: version 70.08.29.00.01
[ 6.273251] intel_rapl: Found RAPL domain package
[ 6.273253] intel_rapl: Found RAPL domain core
[ 6.276408] nouveau 0000:01:00.0: fb: 512 MiB DDR3
[ 6.704011] usb 2-1.4: device descriptor read/64, error -110
[ 7.104624] Adding 4095996k swap on /dev/sda5. Priority:-2 extents:1 across:4095996k SSFS
[ 7.413539] audit: type=1400 audit(1558352743.004:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=829 comm="apparmor_parser"
[ 7.413542] audit: type=1400 audit(1558352743.004:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=829 comm="apparmor_parser"
[ 7.413543] audit: type=1400 audit(1558352743.004:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=829 comm="apparmor_parser"
[ 7.413545] audit: type=1400 audit(1558352743.004:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=829 comm="apparmor_parser"
[ 7.415094] audit: type=1400 audit(1558352743.004:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=832 comm="apparmor_parser"
[ 7.415097] audit: type=1400 audit(1558352743.004:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=832 comm="apparmor_parser"
[ 7.415098] audit: type=1400 audit(1558352743.004:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=832 comm="apparmor_parser"
[ 7.416452] audit: type=1400 audit(1558352743.008:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=833 comm="apparmor_parser"
[ 7.418367] audit: type=1400 audit(1558352743.008:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=836 comm="apparmor_parser"
[ 7.420696] audit: type=1400 audit(1558352743.012:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-soffice" pid=837 comm="apparmor_parser"
[ 7.443857] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[ 7.443899] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[ 7.443933] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[ 7.443965] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[ 7.584546] [TTM] Zone kernel: Available graphics memory: 2011110 kiB
[ 7.584549] [TTM] Initializing pool allocator
[ 7.584555] [TTM] Initializing DMA pool allocator
[ 7.584577] nouveau 0000:01:00.0: DRM: VRAM: 512 MiB
[ 7.584579] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB
[ 7.584590] nouveau 0000:01:00.0: DRM: TMDS table version 2.0
[ 7.584591] nouveau 0000:01:00.0: DRM: DCB version 4.0
[ 7.584593] nouveau 0000:01:00.0: DRM: DCB outp 00: 01000302 00020030
[ 7.584594] nouveau 0000:01:00.0: DRM: DCB outp 01: 02000300 00000000
[ 7.584595] nouveau 0000:01:00.0: DRM: DCB outp 02: 08011392 00020020
[ 7.584596] nouveau 0000:01:00.0: DRM: DCB outp 03: 04022310 00000000
[ 7.584598] nouveau 0000:01:00.0: DRM: DCB conn 00: 00001030
[ 7.584599] nouveau 0000:01:00.0: DRM: DCB conn 01: 00002161
[ 7.584600] nouveau 0000:01:00.0: DRM: DCB conn 02: 00000200
[ 7.585546] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.585547] [drm] Driver supports precise vblank timestamp query.
[ 7.586385] nouveau 0000:01:00.0: DRM: MM: using COPY0 for buffer copies
[ 7.690805] nouveau 0000:01:00.0: DRM: allocated 1920x1080 fb: 0x60000, bo 000000003e03bda7
[ 7.690878] fbcon: nouveaufb (fb0) is primary device
[ 7.690948] Console: switching to colour frame buffer device 240x67
[ 7.690969] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 7.704033] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 0
[ 8.183812] IPv6: ADDRCONF(NETDEV_UP): enp4s0: link is not ready
[ 8.362621] r8169 0000:04:00.0 enp4s0: link down
[ 8.362625] r8169 0000:04:00.0 enp4s0: link down
[ 8.362683] IPv6: ADDRCONF(NETDEV_UP): enp4s0: link is not ready
[ 11.110149] r8169 0000:04:00.0 enp4s0: link up
[ 11.110160] IPv6: ADDRCONF(NETDEV_CHANGE): enp4s0: link becomes ready
[ 22.320050] usb 2-1.4: device descriptor read/64, error -110
[ 22.508056] usb 2-1.4: new high-speed USB device number 5 using ehci-pci
[ 27.696053] usb 2-1.4: device descriptor read/64, error -110
[ 43.153317] rfkill: input handler disabled
[ 43.202003] usb 2-1.4: device descriptor read/64, error -110
[ 43.308266] usb 2-1-port4: attempt power cycle
[ 43.903238] usb 2-1.4: new high-speed USB device number 6 using ehci-pci
[ 54.500109] usb 2-1.4: device not accepting address 6, error -110
[ 54.579441] usb 2-1.4: new high-speed USB device number 7 using ehci-pci
[ 65.231194] usb 2-1.4: device not accepting address 7, error -110
[ 65.231311] usb 2-1-port4: unable to enumerate USB device
[ 65.311132] usb 2-1.6: new high-speed USB device number 8 using ehci-pci
[ 65.673907] usb 2-1.6: New USB device found, idVendor=046d, idProduct=081d, bcdDevice= 0.10
[ 65.673909] usb 2-1.6: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 65.673911] usb 2-1.6: SerialNumber: 6C9617C0
[ 65.687460] media: Linux media interface: v0.10
[ 65.694724] videodev: Linux video capture interface: v2.00
[ 65.932540] usb 2-1.6: set resolution quirk: cval->res = 384
[ 65.932940] usbcore: registered new interface driver snd-usb-audio
[ 65.932987] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081d)
[ 65.967705] uvcvideo 2-1.6:1.2: Entity type for entity Extension 4 was not initialized!
[ 65.967709] uvcvideo 2-1.6:1.2: Entity type for entity Processing 2 was not initialized!
[ 65.967712] uvcvideo 2-1.6:1.2: Entity type for entity Camera 1 was not initialized!
[ 65.967714] uvcvideo 2-1.6:1.2: Entity type for entity Extension 5 was not initialized!
[ 65.967716] uvcvideo 2-1.6:1.2: Entity type for entity Extension 6 was not initialized!
[ 65.967719] uvcvideo 2-1.6:1.2: Entity type for entity Extension 7 was not initialized!
[ 65.967721] uvcvideo 2-1.6:1.2: Entity type for entity Extension 8 was not initialized!
[ 65.967859] input: UVC Camera (046d:081d) as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.2/input/input18
[ 65.968006] usbcore: registered new interface driver uvcvideo
[ 65.968008] USB Video Class driver (1.1.1)
[ 65.993396] usb 2-1.6: current rate 0 is different from the runtime rate 48000
[ 66.008134] usb 2-1.6: current rate 0 is different from the runtime rate 48000
[ 74.193872] usb 2-1.4: new high-speed USB device number 9 using ehci-pci
[ 79.431674] usb 2-1.4: device descriptor read/64, error -110
[ 95.043648] usb 2-1.4: device descriptor read/64, error -110
[ 95.231588] usb 2-1.4: new high-speed USB device number 10 using ehci-pci
[ 100.418776] usb 2-1.4: device descriptor read/64, error -110
[ 116.032962] usb 2-1.4: device descriptor read/64, error -110
[ 116.141096] usb 2-1-port4: attempt power cycle
[ 116.220948] usb 2-1.6: reset high-speed USB device number 8 using ehci-pci
[ 116.744894] usb 2-1.4: new high-speed USB device number 11 using ehci-pci
[ 127.423950] usb 2-1.4: device not accepting address 11, error -110
[ 127.503940] usb 2-1.4: new high-speed USB device number 12 using ehci-pci
[ 138.175593] usb 2-1.4: device not accepting address 12, error -110
[ 138.175768] usb 2-1-port4: unable to enumerate USB device gerard@PC4:~$ dmesg | grep -i fail
[ 0.056750] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.638297] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS? http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#4 Le 20/05/2019, à 14:22
- inbox
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Salut,
Ce n'est donc pas un problème.
En réalité, les Windows affichent rapidement le bureau, mais il te faut encore patienter que tout soit chargé pour que ton système soit utilisable. Les Linux, finissent de charger ce qui doit l'être et n'affichent le bureau que lorsque ton système est réellement utilisable.
A+
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
#5 Le 20/05/2019, à 14:32
- kholo
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
dmesg donne le nombre de sec depuis le démarrage :
[ 138.175768] usb 2-1-port4: unable to enumerate USB device ici 138.175768 sec
tu penses bien que si Doz le fait pas c'est pour ne pas trop divulguer cette info qui ne leur serai pas favorable !
Hors ligne
#6 Le 20/05/2019, à 14:54
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
inbox a écrit :
Les Windows affichent rapidement le bureau, mais il te faut encore patienter que tout soit chargé pour que ton système soit utilisable. Les Linux, finissent de charger ce qui doit l'être et n'affichent le bureau que lorsque ton système est réellement utilisable.
Merci inbox voilà une info intéressante
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#7 Le 20/05/2019, à 15:03
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
kholo a écrit :
dmesg donne le nombre de sec depuis le démarrage :
[ 138.175768] usb 2-1-port4: unable to enumerate USB deviceici 138.175768 sec
tu penses bien que si Doz le fait pas c'est pour ne pas trop divulguer cette info qui ne leur serai pas favorable !
Heu pas tout compris
ces 138s sont pour Ubuntu, ce que je suppose, ou pour windows au cas où cette info serait mémorisée qq part lors de son boot, mais j'en doute
Je dis ça car 138s ça fait 2mn 18s et mon Ub était opérationnel en 50s environ ??
@+
PS : si tu considères que 40+8s sont acceptable pour ce type de PC, et malgré son SSD, je marque résolu.
J'aurai néanmoins appris des trucs !
Dernière modification par winux (Le 20/05/2019, à 15:04)
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#8 Le 20/05/2019, à 15:14
- inbox
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Est-ce que tu utilises une multiprise USB ? Y a-t-il des périphériques connectés sur celle ci ?
Dernière modification par inbox (Le 20/05/2019, à 15:15)
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
#9 Le 20/05/2019, à 19:06
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
inbox a écrit :
Est-ce que tu utilises une multiprise USB ? Y a-t-il des périphériques connectés sur celle ci ?
Non j'ai simplement un retour de 4 prises arrières (ou sur la carte mère je ne sais plus) en face avant, sinon pas de Hub USB.
J'en ai assez en face avant : 6 USB2 et 2 USB3. Lorsque j'ai fait le test il n'y avait rien de connecté, à part en face arrière le clavier, la souris et la webcam inactive à ce moment là.
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#10 Le 20/05/2019, à 19:24
- inbox
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Dans ce cas, les messages d'erreurs concernant l'usb, proviennent certainement de ta webcam. Pour vérifier, il te suffit de démarrer sans, puis de vérifier le retour de dmesg.
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
#11 Le 20/05/2019, à 22:41
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Ok je ferai ça demain, là je vais bouquiner au lit, un Michael Conelly passionnant !!
@+
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#12 Le 21/05/2019, à 08:17
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Salut
J'ai débranché la webcam mais no change, je vois toujours en rouge des lignes de type
0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 22.320023] usb 2-1.4: device descriptor read/64, error -110
[ 22.508017] usb 2-1.4: new high-speed USB device number 5 using ehci-pci
[ 27.696016] usb 2-1.4: device descriptor read/64, error -110
[ 30.635349] rfkill: input handler disabled
[ 43.312014] usb 2-1.4: device descriptor read/64, error -110
[ 43.420154] usb 2-1-port4: attempt power cycle
[ 44.024014] usb 2-1.4: new high-speed USB device number 6 using ehci-pci
[ 54.704011] usb 2-1.4: device not accepting address 6, error -110
[ 54.784032] usb 2-1.4: new high-speed USB device number 7 using ehci-pci
[ 65.456014] usb 2-1.4: device not accepting address 7, error -110
[ 65.456189] usb 2-1-port4: unable to enumerate USB deviceJe vois qu'il fait le tour des devices de 5 à 7 mais ignore ce que ça veut dire ?
[ 54.784032] usb 2-1.4: new high-speed USB device number 7 using ehci-pci
[ 65.456014] usb 2-1.4: device not accepting address 7, error -110Voici la totalité du résultat de la commande.
gerard@PC4:~$ dmesg
[ 0.000000] microcode: microcode updated early to revision 0x2f, date = 2019-02-17
[ 0.000000] Linux version 4.18.0-20-generic (buildd@lcy01-amd64-020) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21~18.04.1-Ubuntu SMP Wed May 8 08:43:37 UTC 2019 (Ubuntu 4.18.0-20.21~18.04.1-generic 4.18.20)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-20-generic root=UUID=9e193abd-bd12-4800-aa6a-e92130f3ceff ro quiet splash vt.handoff=1
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009dbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000df7cffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000df7d0000-0x00000000df7d2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000df7d3000-0x00000000df7dffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000df7e0000-0x00000000df7fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011f7fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. P67A-UD3-B3/P67A-UD3-B3, BIOS F2 02/22/2011
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] last_pfn = 0x11f800 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CCFFF write-protect
[ 0.000000] CD000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 2 base 100000000 mask FE0000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] total RAM covered: 4096M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 1G num_reg: 3 lose cover RAM: 0G
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] last_pfn = 0xdf7d0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f5a20-0x000f5a2f] mapped at [(____ptrval____)]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [(____ptrval____)] 97000 size 24576
[ 0.000000] BRK [0x7ff63000, 0x7ff63fff] PGTABLE
[ 0.000000] BRK [0x7ff64000, 0x7ff64fff] PGTABLE
[ 0.000000] BRK [0x7ff65000, 0x7ff65fff] PGTABLE
[ 0.000000] BRK [0x7ff66000, 0x7ff66fff] PGTABLE
[ 0.000000] BRK [0x7ff67000, 0x7ff67fff] PGTABLE
[ 0.000000] BRK [0x7ff68000, 0x7ff68fff] PGTABLE
[ 0.000000] BRK [0x7ff69000, 0x7ff69fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x33465000-0x35a29fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F7180 000014 (v00 GBT )
[ 0.000000] ACPI: RSDT 0x00000000DF7D3040 00004C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: FACP 0x00000000DF7D3100 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: DSDT 0x00000000DF7D31C0 00469B (v01 GBT GBTUACPI 00001000 MSFT 04000000)
[ 0.000000] ACPI: FACS 0x00000000DF7D0000 000040
[ 0.000000] ACPI: HPET 0x00000000DF7D79C0 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
[ 0.000000] ACPI: MCFG 0x00000000DF7D7A40 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: ASPT 0x00000000DF7D7B00 000034 (v07 GBT PerfTune 312E3042 UTBG 01010101)
[ 0.000000] ACPI: SSPT 0x00000000DF7D7B40 00239C (v01 GBT SsptHead 312E3042 UTBG 01010101)
[ 0.000000] ACPI: EUDS 0x00000000DF7D9EE0 0000C0 (v01 GBT 00000000 00000000)
[ 0.000000] ACPI: MATS 0x00000000DF7D9FA0 000034 (v01 GBT 00000000 00000000)
[ 0.000000] ACPI: TAMG 0x00000000DF7DA000 000A3A (v01 GBT GBT B0 5455312E BG?? 53450101)
[ 0.000000] ACPI: APIC 0x00000000DF7D78C0 0000BC (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: SSDT 0x00000000DF7DAA40 001F4C (v01 INTEL PPM RCM 80000001 INTL 20061109)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000011f7fffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x11f7d3000-0x11f7fdfff]
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000011f7fffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000df7cffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000011f7fffff]
[ 0.000000] Reserved but unavailable: 2196 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000011f7fffff]
[ 0.000000] On node 0 totalpages: 1044332
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14240 pages used for memmap
[ 0.000000] DMA32 zone: 911312 pages, LIFO batch:31
[ 0.000000] Normal zone: 2016 pages used for memmap
[ 0.000000] Normal zone: 129024 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] dfl dfl lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf7d0000-0xdf7d2fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf7d3000-0xdf7dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf7e0000-0xdf7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf800000-0xf3ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf4000000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
[ 0.000000] [mem 0xdf800000-0xf3ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] random: get_random_bytes called from start_kernel+0x99/0x55a with crng_init=0
[ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] percpu: Embedded 46 pages/cpu @(____ptrval____) s151552 r8192 d28672 u262144
[ 0.000000] pcpu-alloc: s151552 r8192 d28672 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1027991
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-20-generic root=UUID=9e193abd-bd12-4800-aa6a-e92130f3ceff ro quiet splash vt.handoff=1
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3977280K/4177328K available (12300K kernel code, 2634K rwdata, 4384K rodata, 2460K init, 2340K bss, 200048K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Kernel/User page tables isolation: enabled
[ 0.000000] ftrace: allocating 40847 entries in 160 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS: 524544, nr_irqs: 488, preallocated irqs: 16
[ 0.000000] vt handoff: transparent VT on vt#1
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] ACPI: Core revision 20180531
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] APIC: Switch to symmetric I/O mode setup
[ 0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.020000] tsc: Fast TSC calibration using PIT
[ 0.024000] tsc: Detected 3292.498 MHz processor
[ 0.024000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2f759d92134, max_idle_ns: 440795340478 ns
[ 0.024000] Calibrating delay loop (skipped), value calculated using timer frequency.. 6584.99 BogoMIPS (lpj=13169992)
[ 0.024000] pid_max: default: 32768 minimum: 301
[ 0.024000] Security Framework initialized
[ 0.024000] Yama: becoming mindful.
[ 0.024000] AppArmor: AppArmor initialized
[ 0.024000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.024000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.024000] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.024000] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.024000] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.024000] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.024000] mce: CPU supports 9 MCE banks
[ 0.024000] CPU0: Thermal monitoring enabled (TM1)
[ 0.024000] process: using mwait in idle threads
[ 0.024000] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.024000] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.024000] Spectre V2 : Mitigation: Full generic retpoline
[ 0.024000] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.024000] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 0.024000] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[ 0.024000] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[ 0.024000] MDS: Mitigation: Clear CPU buffers
[ 0.028012] Freeing SMP alternatives memory: 36K
[ 0.032056] TSC deadline timer enabled
[ 0.032058] smpboot: CPU0: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz (family: 0x6, model: 0x2a, stepping: 0x7)
[ 0.032136] Performance Events: PEBS fmt1+, SandyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[ 0.032153] ... version: 3
[ 0.032153] ... bit width: 48
[ 0.032154] ... generic registers: 8
[ 0.032154] ... value mask: 0000ffffffffffff
[ 0.032155] ... max period: 00007fffffffffff
[ 0.032155] ... fixed-purpose events: 3
[ 0.032156] ... event mask: 00000007000000ff
[ 0.032184] Hierarchical SRCU implementation.
[ 0.033031] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.033043] smp: Bringing up secondary CPUs ...
[ 0.033108] x86: Booting SMP configuration:
[ 0.033109] .... node #0, CPUs: #1 #2 #3
[ 0.040024] smp: Brought up 1 node, 4 CPUs
[ 0.040024] smpboot: Max logical packages: 2
[ 0.040024] smpboot: Total of 4 processors activated (26339.98 BogoMIPS)
[ 0.042105] devtmpfs: initialized
[ 0.042105] x86/mm: Memory block size: 128MB
[ 0.042105] PM: Registering ACPI NVS region [mem 0xdf7d0000-0xdf7d2fff] (12288 bytes)
[ 0.042151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.042151] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.042151] pinctrl core: initialized pinctrl subsystem
[ 0.042151] RTC time: 5:52:33, date: 05/21/19
[ 0.042151] NET: Registered protocol family 16
[ 0.042151] audit: initializing netlink subsys (disabled)
[ 0.042151] audit: type=2000 audit(1558417953.040:1): state=initialized audit_enabled=0 res=1
[ 0.042151] cpuidle: using governor ladder
[ 0.042151] cpuidle: using governor menu
[ 0.042151] ACPI: bus type PCI registered
[ 0.042151] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.042151] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[ 0.042151] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[ 0.042151] pmd_set_huge: Cannot satisfy [mem 0xf4000000-0xf4200000] with a huge-page mapping due to MTRR override.
[ 0.042151] PCI: Using configuration type 1 for base access
[ 0.042151] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[ 0.044404] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.044404] ACPI: Added _OSI(Module Device)
[ 0.044404] ACPI: Added _OSI(Processor Device)
[ 0.044404] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.044404] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.044404] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.044404] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.047242] ACPI: 2 ACPI AML tables successfully acquired and loaded
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.048002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - \_SB_.PCI0.LNK9 (20180531/dspkginit-414)
[ 0.052812] ACPI: Interpreter enabled
[ 0.052825] ACPI: (supports S0 S3 S4 S5)
[ 0.052826] ACPI: Using IOAPIC for interrupt routing
[ 0.052843] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.052969] ACPI: Enabled 5 GPEs in block 00 to 3F
[ 0.056738] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
[ 0.056742] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.056746] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.056956] PCI host bridge to bus 0000:00
[ 0.056958] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.056959] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.056960] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.056961] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.056962] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfebfffff window]
[ 0.056963] pci_bus 0000:00: root bus resource [bus 00-3f]
[ 0.056970] pci 0000:00:00.0: [8086:0100] type 00 class 0x060000
[ 0.057049] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[ 0.057076] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.057143] pci 0000:00:01.1: [8086:0105] type 01 class 0x060400
[ 0.057167] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
[ 0.057257] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.057280] pci 0000:00:16.0: reg 0x10: [mem 0xfbfff000-0xfbfff00f 64bit]
[ 0.057348] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.057426] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.057446] pci 0000:00:1a.0: reg 0x10: [mem 0xfbffe000-0xfbffe3ff]
[ 0.057524] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.057599] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.057619] pci 0000:00:1b.0: reg 0x10: [mem 0xfbff4000-0xfbff7fff 64bit]
[ 0.057686] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.057761] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.057833] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.057916] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[ 0.057994] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.058075] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[ 0.058148] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.058233] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.058253] pci 0000:00:1d.0: reg 0x10: [mem 0xfbffd000-0xfbffd3ff]
[ 0.058331] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.058404] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.058516] pci 0000:00:1f.0: [8086:1c46] type 00 class 0x060100
[ 0.058683] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.058699] pci 0000:00:1f.2: reg 0x10: [io 0xff00-0xff07]
[ 0.058706] pci 0000:00:1f.2: reg 0x14: [io 0xfe00-0xfe03]
[ 0.058712] pci 0000:00:1f.2: reg 0x18: [io 0xfd00-0xfd07]
[ 0.058718] pci 0000:00:1f.2: reg 0x1c: [io 0xfc00-0xfc03]
[ 0.058725] pci 0000:00:1f.2: reg 0x20: [io 0xfb00-0xfb1f]
[ 0.058731] pci 0000:00:1f.2: reg 0x24: [mem 0xfbffc000-0xfbffc7ff]
[ 0.058768] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.058836] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.058853] pci 0000:00:1f.3: reg 0x10: [mem 0xfbffb000-0xfbffb0ff 64bit]
[ 0.058871] pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
[ 0.058973] pci 0000:01:00.0: [10de:0de1] type 00 class 0x030000
[ 0.058987] pci 0000:01:00.0: reg 0x10: [mem 0xf9000000-0xf9ffffff]
[ 0.058995] pci 0000:01:00.0: reg 0x14: [mem 0xe0000000-0xe7ffffff 64bit pref]
[ 0.059003] pci 0000:01:00.0: reg 0x1c: [mem 0xee000000-0xefffffff 64bit pref]
[ 0.059009] pci 0000:01:00.0: reg 0x24: [io 0xef00-0xef7f]
[ 0.059014] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[ 0.059019] pci 0000:01:00.0: enabling Extended Tags
[ 0.059090] pci 0000:01:00.1: [10de:0bea] type 00 class 0x040300
[ 0.059102] pci 0000:01:00.1: reg 0x10: [mem 0xfaffc000-0xfaffffff]
[ 0.059132] pci 0000:01:00.1: enabling Extended Tags
[ 0.068023] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.068026] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.068030] pci 0000:00:01.0: bridge window [mem 0xf9000000-0xfaffffff]
[ 0.068034] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.068090] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330
[ 0.068121] pci 0000:02:00.0: reg 0x10: [mem 0xfbdfe000-0xfbdfffff 64bit]
[ 0.068192] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.080018] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 0.080022] pci 0000:00:01.1: bridge window [mem 0xfbd00000-0xfbdfffff]
[ 0.080081] pci 0000:00:1c.0: PCI bridge to [bus 03]
[ 0.080155] pci 0000:04:00.0: [10ec:8168] type 00 class 0x020000
[ 0.080188] pci 0000:04:00.0: reg 0x10: [io 0xde00-0xdeff]
[ 0.080220] pci 0000:04:00.0: reg 0x18: [mem 0xfbeff000-0xfbefffff 64bit pref]
[ 0.080241] pci 0000:04:00.0: reg 0x20: [mem 0xfbef8000-0xfbefbfff 64bit pref]
[ 0.080349] pci 0000:04:00.0: supports D1 D2
[ 0.080350] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.080440] pci 0000:00:1c.2: ASPM: current common clock configuration is broken, reconfiguring
[ 0.092027] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.092032] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.092041] pci 0000:00:1c.2: bridge window [mem 0xfbe00000-0xfbefffff 64bit pref]
[ 0.092124] pci 0000:05:00.0: [1283:8892] type 01 class 0x060400
[ 0.092287] pci 0000:05:00.0: supports D1 D2
[ 0.092288] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.092353] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.092364] pci 0000:00:1c.3: PCI bridge to [bus 05-06]
[ 0.092433] pci_bus 0000:06: extended config space not accessible
[ 0.092526] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.092577] pci_bus 0000:07: extended config space not accessible
[ 0.092623] pci 0000:00:1e.0: PCI bridge to [bus 07] (subtractive decode)
[ 0.092631] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.092632] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.092633] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.092634] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.092636] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xfebfffff window] (subtractive decode)
[ 0.093106] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 0.093163] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
[ 0.093220] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.093277] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.093333] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.093390] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.093446] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.093503] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.093742] SCSI subsystem initialized
[ 0.093752] libata version 3.00 loaded.
[ 0.093752] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[ 0.093752] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.093752] pci 0000:01:00.0: vgaarb: bridge control possible
[ 0.093752] vgaarb: loaded
[ 0.093752] ACPI: bus type USB registered
[ 0.093752] usbcore: registered new interface driver usbfs
[ 0.093752] usbcore: registered new interface driver hub
[ 0.093752] usbcore: registered new device driver usb
[ 0.093752] pps_core: LinuxPPS API ver. 1 registered
[ 0.093752] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.093752] PTP clock support registered
[ 0.093752] EDAC MC: Ver: 3.0.0
[ 0.093752] PCI: Using ACPI for IRQ routing
[ 0.093752] PCI: pci_cache_line_size set to 64 bytes
[ 0.093752] e820: reserve RAM buffer [mem 0x0009dc00-0x0009ffff]
[ 0.093752] e820: reserve RAM buffer [mem 0xdf7d0000-0xdfffffff]
[ 0.093752] e820: reserve RAM buffer [mem 0x11f800000-0x11fffffff]
[ 0.093752] NetLabel: Initializing
[ 0.093752] NetLabel: domain hash size = 128
[ 0.093752] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.093752] NetLabel: unlabeled traffic allowed by default
[ 0.093752] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.093752] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.097020] clocksource: Switched to clocksource tsc-early
[ 0.104584] VFS: Disk quotas dquot_6.6.0
[ 0.104598] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.104680] AppArmor: AppArmor Filesystem Enabled
[ 0.104703] pnp: PnP ACPI init
[ 0.104872] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 0.104873] system 00:00: [io 0x0290-0x029f] has been reserved
[ 0.104875] system 00:00: [io 0x0800-0x087f] has been reserved
[ 0.104876] system 00:00: [io 0x0290-0x0294] has been reserved
[ 0.104877] system 00:00: [io 0x0880-0x088f] has been reserved
[ 0.104882] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.104948] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.105163] system 00:02: [io 0x0400-0x04cf] has been reserved
[ 0.105164] system 00:02: [io 0x04d2-0x04ff] has been reserved
[ 0.105167] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.105196] system 00:03: [io 0x1000-0x107f] has been reserved
[ 0.105197] system 00:03: [io 0x1080-0x10ff] has been reserved
[ 0.105200] system 00:03: [io 0x1100-0x117f] has been reserved
[ 0.105201] system 00:03: [io 0x1180-0x11ff] has been reserved
[ 0.105204] system 00:03: Plug and Play ACPI device, IDs ICD0001 PNP0c02 (active)
[ 0.105392] system 00:04: [io 0x0454-0x0457] has been reserved
[ 0.105396] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.105432] system 00:05: [mem 0xf4000000-0xf7ffffff] has been reserved
[ 0.105435] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.105659] system 00:06: [mem 0x000d0a00-0x000d3fff] has been reserved
[ 0.105661] system 00:06: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.105662] system 00:06: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.105663] system 00:06: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.105665] system 00:06: [mem 0xdf7d0000-0xdf7dffff] could not be reserved
[ 0.105666] system 00:06: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.105668] system 00:06: [mem 0x00100000-0xdf7cffff] could not be reserved
[ 0.105669] system 00:06: [mem 0xdf7e0000-0xdf7fffff] has been reserved
[ 0.105670] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.105672] system 00:06: [mem 0xfed10000-0xfed1dfff] has been reserved
[ 0.105673] system 00:06: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.105674] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.105676] system 00:06: [mem 0xffb00000-0xffb7ffff] has been reserved
[ 0.105677] system 00:06: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.105678] system 00:06: [mem 0x000e0000-0x000effff] has been reserved
[ 0.105680] system 00:06: [mem 0x20000000-0x201fffff] could not be reserved
[ 0.105681] system 00:06: [mem 0x40000000-0x400fffff] could not be reserved
[ 0.105682] system 00:06: [mem 0xdf800000-0xdfffffff] could not be reserved
[ 0.105685] system 00:06: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.105690] pnp: PnP ACPI: found 7 devices
[ 0.111148] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.111165] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 03] add_size 1000
[ 0.111167] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[ 0.111169] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000 add_align 100000
[ 0.111205] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf0000000-0xf01fffff]
[ 0.111208] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf0200000-0xf03fffff 64bit pref]
[ 0.111210] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.111213] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa07ffff pref]
[ 0.111214] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.111216] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.111218] pci 0000:00:01.0: bridge window [mem 0xf9000000-0xfaffffff]
[ 0.111220] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.111222] pci 0000:00:01.1: PCI bridge to [bus 02]
[ 0.111224] pci 0000:00:01.1: bridge window [mem 0xfbd00000-0xfbdfffff]
[ 0.111227] pci 0000:00:1c.0: PCI bridge to [bus 03]
[ 0.111229] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.111233] pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf01fffff]
[ 0.111236] pci 0000:00:1c.0: bridge window [mem 0xf0200000-0xf03fffff 64bit pref]
[ 0.111241] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.111243] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.111248] pci 0000:00:1c.2: bridge window [mem 0xfbe00000-0xfbefffff 64bit pref]
[ 0.111253] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 0.111276] pci 0000:00:1c.3: PCI bridge to [bus 05-06]
[ 0.111285] pci 0000:00:1e.0: PCI bridge to [bus 07]
[ 0.111294] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.111295] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.111296] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.111297] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window]
[ 0.111299] pci_bus 0000:00: resource 8 [mem 0xe0000000-0xfebfffff window]
[ 0.111300] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 0.111301] pci_bus 0000:01: resource 1 [mem 0xf9000000-0xfaffffff]
[ 0.111302] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.111303] pci_bus 0000:02: resource 1 [mem 0xfbd00000-0xfbdfffff]
[ 0.111305] pci_bus 0000:03: resource 0 [io 0x2000-0x2fff]
[ 0.111306] pci_bus 0000:03: resource 1 [mem 0xf0000000-0xf01fffff]
[ 0.111307] pci_bus 0000:03: resource 2 [mem 0xf0200000-0xf03fffff 64bit pref]
[ 0.111308] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.111309] pci_bus 0000:04: resource 2 [mem 0xfbe00000-0xfbefffff 64bit pref]
[ 0.111310] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7 window]
[ 0.111311] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff window]
[ 0.111312] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.111313] pci_bus 0000:07: resource 7 [mem 0x000c0000-0x000dffff window]
[ 0.111314] pci_bus 0000:07: resource 8 [mem 0xe0000000-0xfebfffff window]
[ 0.111376] NET: Registered protocol family 2
[ 0.111513] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.111526] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.111572] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.111626] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.111651] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.111661] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.111695] NET: Registered protocol family 1
[ 0.111699] NET: Registered protocol family 44
[ 0.136133] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x6c0 took 23850 usecs
[ 0.156128] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x6c0 took 19515 usecs
[ 0.156146] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.156150] pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
[ 0.156299] PCI: CLS 4 bytes, default 64
[ 0.156326] Unpacking initramfs...
[ 0.558144] Freeing initrd memory: 38676K
[ 0.558159] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.558161] software IO TLB [mem 0xdb7d0000-0xdf7d0000] (64MB) mapped at [(____ptrval____)-(____ptrval____)]
[ 0.558359] Scanning for low memory corruption every 60 seconds
[ 0.558875] Initialise system trusted keyrings
[ 0.558883] Key type blacklist registered
[ 0.558905] workingset: timestamp_bits=36 max_order=20 bucket_order=0
[ 0.559841] zbud: loaded
[ 0.560200] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560322] fuse init (API version 7.27)
[ 0.560363] pstore: using deflate compression
[ 0.561137] Key type asymmetric registered
[ 0.561138] Asymmetric key parser 'x509' registered
[ 0.561164] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.561186] io scheduler noop registered
[ 0.561186] io scheduler deadline registered
[ 0.561206] io scheduler cfq registered (default)
[ 0.561402] pcieport 0000:00:1c.0: enabling device (0000 -> 0003)
[ 0.561717] shpchp 0000:05:00.0: Requesting control of SHPC hotplug via OSHP (\_SB_.PCI0.PEX3)
[ 0.561720] shpchp 0000:05:00.0: Requesting control of SHPC hotplug via OSHP (\_SB_.PCI0)
[ 0.561723] shpchp 0000:05:00.0: Cannot get control of SHPC hotplug
[ 0.561729] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.561768] vesafb: mode is 640x480x32, linelength=2560, pages=0
[ 0.561768] vesafb: scrolling: redraw
[ 0.561770] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.561776] vesafb: framebuffer at 0xef000000, mapped to 0x(____ptrval____), using 1216k, total 1216k
[ 0.561841] Console: switching to colour frame buffer device 80x30
[ 0.561849] fb0: VESA VGA frame buffer device
[ 0.561860] intel_idle: MWAIT substates: 0x1120
[ 0.561860] intel_idle: v0.4.1 model 0x2A
[ 0.561958] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.562013] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.562020] ACPI: Power Button [PWRB]
[ 0.562050] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.562079] ACPI: Power Button [PWRF]
[ 0.562811] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.564074] Linux agpgart interface v0.103
[ 0.565337] loop: module loaded
[ 0.565454] libphy: Fixed MDIO Bus: probed
[ 0.565455] tun: Universal TUN/TAP device driver, 1.6
[ 0.565473] PPP generic driver version 2.4.2
[ 0.565497] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.565498] ehci-pci: EHCI PCI platform driver
[ 0.565582] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.565590] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.565600] ehci-pci 0000:00:1a.0: debug port 2
[ 0.569510] ehci-pci 0000:00:1a.0: cache line size of 4 is not supported
[ 0.569520] ehci-pci 0000:00:1a.0: irq 18, io mem 0xfbffe000
[ 0.584050] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.584117] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 0.584120] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.584122] usb usb1: Product: EHCI Host Controller
[ 0.584124] usb usb1: Manufacturer: Linux 4.18.0-20-generic ehci_hcd
[ 0.584126] usb usb1: SerialNumber: 0000:00:1a.0
[ 0.584320] hub 1-0:1.0: USB hub found
[ 0.584326] hub 1-0:1.0: 2 ports detected
[ 0.584480] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.584483] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.584492] ehci-pci 0000:00:1d.0: debug port 2
[ 0.588401] ehci-pci 0000:00:1d.0: cache line size of 4 is not supported
[ 0.588408] ehci-pci 0000:00:1d.0: irq 23, io mem 0xfbffd000
[ 0.604049] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.604115] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 0.604118] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.604120] usb usb2: Product: EHCI Host Controller
[ 0.604122] usb usb2: Manufacturer: Linux 4.18.0-20-generic ehci_hcd
[ 0.604125] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.604276] hub 2-0:1.0: USB hub found
[ 0.604281] hub 2-0:1.0: 2 ports detected
[ 0.604363] ehci-platform: EHCI generic platform driver
[ 0.604368] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.604371] ohci-pci: OHCI PCI platform driver
[ 0.604376] ohci-platform: OHCI generic platform driver
[ 0.604380] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.604441] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 0.604444] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 0.604525] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[ 0.604658] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 0.604659] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.604660] usb usb3: Product: xHCI Host Controller
[ 0.604661] usb usb3: Manufacturer: Linux 4.18.0-20-generic xhci-hcd
[ 0.604662] usb usb3: SerialNumber: 0000:02:00.0
[ 0.604786] hub 3-0:1.0: USB hub found
[ 0.604793] hub 3-0:1.0: 2 ports detected
[ 0.604864] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 0.604866] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[ 0.604868] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 0.608012] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.608033] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.18
[ 0.608034] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.608036] usb usb4: Product: xHCI Host Controller
[ 0.608037] usb usb4: Manufacturer: Linux 4.18.0-20-generic xhci-hcd
[ 0.608045] usb usb4: SerialNumber: 0000:02:00.0
[ 0.608165] hub 4-0:1.0: USB hub found
[ 0.608172] hub 4-0:1.0: 2 ports detected
[ 0.608259] i8042: PNP: No PS/2 controller found.
[ 0.608259] i8042: Probing ports directly.
[ 0.640612] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
[ 0.640612] i8042: If AUX port is really absent please use the 'i8042.noaux' option
[ 0.896140] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.896378] mousedev: PS/2 mouse device common for all mice
[ 0.896674] rtc_cmos 00:01: RTC can wake from S4
[ 0.896826] rtc_cmos 00:01: registered as rtc0
[ 0.896846] rtc_cmos 00:01: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.896851] i2c /dev entries driver
[ 0.896853] pcie_mp2_amd: AMD(R) PCI-E MP2 Communication Driver Version: 1.0
[ 0.896894] device-mapper: uevent: version 1.0.3
[ 0.896960] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[ 0.896964] intel_pstate: Intel P-state driver initializing
[ 0.897201] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.897645] NET: Registered protocol family 10
[ 0.900978] Segment Routing with IPv6
[ 0.900993] NET: Registered protocol family 17
[ 0.901037] Key type dns_resolver registered
[ 0.901291] RAS: Correctable Errors collector initialized.
[ 0.901312] microcode: sig=0x206a7, pf=0x2, revision=0x2f
[ 0.901383] microcode: Microcode Update Driver: v2.2.
[ 0.901389] sched_clock: Marking stable (901380200, 0)->(884721851, 16658349)
[ 0.901518] registered taskstats version 1
[ 0.901524] Loading compiled-in X.509 certificates
[ 0.903421] Loaded X.509 cert 'Build time autogenerated kernel key: 377cdf01bd4aa8cd057eca9f88365c72625360bc'
[ 0.903437] zswap: loaded using pool lzo/zbud
[ 0.906040] Key type big_key registered
[ 0.906042] Key type trusted registered
[ 0.907279] Key type encrypted registered
[ 0.907281] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.907285] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[ 0.907288] ima: Allocated hash algorithm: sha1
[ 0.907302] evm: Initialising EVM extended attributes:
[ 0.907303] evm: security.selinux
[ 0.907303] evm: security.SMACK64
[ 0.907303] evm: security.SMACK64EXEC
[ 0.907304] evm: security.SMACK64TRANSMUTE
[ 0.907304] evm: security.SMACK64MMAP
[ 0.907305] evm: security.apparmor
[ 0.907305] evm: security.ima
[ 0.907305] evm: security.capability
[ 0.907306] evm: HMAC attrs: 0x1
[ 0.907547] Magic number: 3:439:871
[ 0.907641] rtc_cmos 00:01: setting system clock to 2019-05-21 05:52:34 UTC (1558417954)
[ 0.909978] Freeing unused kernel image memory: 2460K
[ 0.936061] Write protecting the kernel read-only data: 20480k
[ 0.936621] Freeing unused kernel image memory: 2008K
[ 0.936890] Freeing unused kernel image memory: 1760K
[ 0.940013] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 0.944569] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.944569] x86/mm: Checking user space page tables
[ 0.951605] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.964019] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.007438] ahci 0000:00:1f.2: version 3.0
[ 1.007589] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 1.008868] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.008875] r8169 0000:04:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 1.009204] r8169 0000:04:00.0 eth0: RTL8168e/8111e, 1c:6f:65:d7:53:ac, XID 2c200000, IRQ 30
[ 1.009205] r8169 0000:04:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 1.020165] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 1.020168] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ems apst
[ 1.025846] r8169 0000:04:00.0 enp4s0: renamed from eth0
[ 1.080433] usb 1-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 1.080443] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.080617] scsi host0: ahci
[ 1.080703] hub 1-1:1.0: USB hub found
[ 1.080806] hub 1-1:1.0: 6 ports detected
[ 1.080834] scsi host1: ahci
[ 1.081082] scsi host2: ahci
[ 1.081174] scsi host3: ahci
[ 1.081237] scsi host4: ahci
[ 1.081292] scsi host5: ahci
[ 1.081339] ata1: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc100 irq 29
[ 1.081341] ata2: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc180 irq 29
[ 1.081342] ata3: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc200 irq 29
[ 1.081344] ata4: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc280 irq 29
[ 1.081345] ata5: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc300 irq 29
[ 1.081346] ata6: SATA max UDMA/133 abar m2048@0xfbffc000 port 0xfbffc380 irq 29
[ 1.108822] usb 2-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 1.108824] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.109181] hub 2-1:1.0: USB hub found
[ 1.109416] hub 2-1:1.0: 8 ports detected
[ 1.368054] usb 1-1.2: new low-speed USB device number 3 using ehci-pci
[ 1.396028] usb 2-1.3: new high-speed USB device number 3 using ehci-pci
[ 1.480958] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00
[ 1.480959] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.480960] usb 1-1.2: Product: USB Optical Mouse
[ 1.480961] usb 1-1.2: Manufacturer: Logitech
[ 1.484625] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.487528] usbcore: registered new interface driver usbhid
[ 1.487529] usbhid: USB HID core driver
[ 1.489235] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C077.0001/input/input3
[ 1.489405] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1a.0-1.2/input0
[ 1.504726] usb 2-1.3: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
[ 1.504729] usb 2-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.504731] usb 2-1.3: Product: USB 2.0 Hub
[ 1.504953] hub 2-1.3:1.0: USB hub found
[ 1.505055] hub 2-1.3:1.0: 4 ports detected
[ 1.556045] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.556376] ata1.00: ATA-10: KINGSTON SA400S37240G, SBFKB1E1, max UDMA/133
[ 1.556378] ata1.00: 468862128 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 1.556789] ata1.00: configured for UDMA/133
[ 1.557069] scsi 0:0:0:0: Direct-Access ATA KINGSTON SA400S3 B1E1 PQ: 0 ANSI: 5
[ 1.557410] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB)
[ 1.557417] sd 0:0:0:0: [sda] Write Protect is off
[ 1.557418] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.557423] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.557428] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.558647] sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[ 1.559121] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.560009] usb 1-1.3: new low-speed USB device number 4 using ehci-pci
[ 1.568025] tsc: Refined TSC clocksource calibration: 3292.520 MHz
[ 1.568035] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2f75b1eac7a, max_idle_ns: 440795210882 ns
[ 1.568109] clocksource: Switched to clocksource tsc
[ 1.584055] usb 2-1.4: new high-speed USB device number 4 using ehci-pci
[ 1.674459] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00
[ 1.674461] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.674462] usb 1-1.3: Product: USB Keyboard
[ 1.674463] usb 1-1.3: Manufacturer: Logitech
[ 1.680176] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C31C.0002/input/input4
[ 1.740315] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:1a.0-1.3/input0
[ 1.746137] input: Logitech USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:046D:C31C.0003/input/input5
[ 1.804223] input: Logitech USB Keyboard System Control as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:046D:C31C.0003/input/input6
[ 1.804441] hid-generic 0003:046D:C31C.0003: input,hidraw2: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:1a.0-1.3/input1
[ 1.870796] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.348045] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.360494] ata3.00: ATA-8: WDC WD1001FAES-00W7A0, 05.01D05, max UDMA/133
[ 2.360497] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 2.362839] ata3.00: configured for UDMA/133
[ 2.363110] scsi 2:0:0:0: Direct-Access ATA WDC WD1001FAES-0 1D05 PQ: 0 ANSI: 5
[ 2.363399] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.363498] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 2.363583] sd 2:0:0:0: [sdb] Write Protect is off
[ 2.363584] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.363651] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.371850] sdb: sdb3 sdb4
[ 2.372267] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 2.840062] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.856607] ata4.00: ATAPI: PIONEER DVD-RW DVR-219L, 1.01, max UDMA/100
[ 2.881159] ata4.00: configured for UDMA/100
[ 2.895818] scsi 3:0:0:0: CD-ROM PIONEER DVD-RW DVR-219L 1.01 PQ: 0 ANSI: 5
[ 2.971635] sr 3:0:0:0: [sr0] scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.971637] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.971837] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 2.971995] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 3.448062] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.460502] ata5.00: ATA-8: WDC WD1001FAES-00W7A0, 05.01D05, max UDMA/133
[ 3.460505] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[ 3.462974] ata5.00: configured for UDMA/133
[ 3.463158] scsi 4:0:0:0: Direct-Access ATA WDC WD1001FAES-0 1D05 PQ: 0 ANSI: 5
[ 3.463375] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 3.463565] sd 4:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 3.463590] sd 4:0:0:0: [sdc] Write Protect is off
[ 3.463591] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.463660] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.497360] sdc: sdc1
[ 3.497942] sd 4:0:0:0: [sdc] Attached SCSI disk
[ 3.778955] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.796973] random: fast init done
[ 3.796984] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 3.796994] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 3.797005] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.148169] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
[ 4.150247] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.319588] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 4.336302] systemd[1]: Detected architecture x86-64.
[ 4.338407] systemd[1]: Set hostname to <PC4>.
[ 5.517605] systemd[1]: Created slice System Slice.
[ 5.517689] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.517721] systemd[1]: Listening on udev Kernel Socket.
[ 5.517757] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 5.517793] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 5.517873] systemd[1]: Listening on Journal Audit Socket.
[ 5.517911] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 5.552458] lp: driver loaded but no devices found
[ 5.555011] ppdev: user-space parallel port driver
[ 5.558268] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 5.659842] systemd-journald[297]: Received request to flush runtime journal from PID 1
[ 5.935413] snd_hda_intel 0000:01:00.1: Disabling MSI
[ 5.935418] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[ 5.948855] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC889: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 5.948857] snd_hda_codec_realtek hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 5.948858] snd_hda_codec_realtek hdaudioC0D2: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 5.948859] snd_hda_codec_realtek hdaudioC0D2: mono: mono_out=0x0
[ 5.948860] snd_hda_codec_realtek hdaudioC0D2: dig-out=0x11/0x1e
[ 5.948861] snd_hda_codec_realtek hdaudioC0D2: inputs:
[ 5.948863] snd_hda_codec_realtek hdaudioC0D2: Rear Mic=0x18
[ 5.948864] snd_hda_codec_realtek hdaudioC0D2: Front Mic=0x19
[ 5.948865] snd_hda_codec_realtek hdaudioC0D2: Line=0x1a
[ 5.948866] snd_hda_codec_realtek hdaudioC0D2: CD=0x1c
[ 5.961959] random: crng init done
[ 5.961961] random: 7 urandom warning(s) missed due to ratelimiting
[ 5.963055] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 5.963093] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 5.963126] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 5.963157] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 5.963188] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 5.963238] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 5.963297] input: HDA Intel PCH Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 5.967467] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[ 5.967468] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 5.967469] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 5.967469] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 5.971553] cryptd: max_cpu_qlen set to 1000
[ 5.972792] checking generic (ef000000 130000) vs hw (e0000000 8000000)
[ 5.972793] checking generic (ef000000 130000) vs hw (ee000000 2000000)
[ 5.972794] fb: switching to nouveaufb from VESA VGA
[ 5.972816] Console: switching to colour dummy device 80x25
[ 5.973142] nouveau 0000:01:00.0: NVIDIA GF108 (0c1080a1)
[ 5.997998] AVX version of gcm_enc/dec engaged.
[ 5.997999] AES CTR mode by8 optimization enabled
[ 6.103814] nouveau 0000:01:00.0: bios: version 70.08.29.00.01
[ 6.105500] nouveau 0000:01:00.0: fb: 512 MiB DDR3
[ 6.126171] gpio_ich: GPIO from 436 to 511 on gpio_ich
[ 6.227000] intel_rapl: Found RAPL domain package
[ 6.227001] intel_rapl: Found RAPL domain core
[ 6.704018] usb 2-1.4: device descriptor read/64, error -110
[ 6.798394] Adding 4095996k swap on /dev/sda5. Priority:-2 extents:1 across:4095996k SSFS
[ 7.133751] audit: type=1400 audit(1558417960.720:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=806 comm="apparmor_parser"
[ 7.133754] audit: type=1400 audit(1558417960.720:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=806 comm="apparmor_parser"
[ 7.133755] audit: type=1400 audit(1558417960.720:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=806 comm="apparmor_parser"
[ 7.134643] audit: type=1400 audit(1558417960.720:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=803 comm="apparmor_parser"
[ 7.134645] audit: type=1400 audit(1558417960.720:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=803 comm="apparmor_parser"
[ 7.134647] audit: type=1400 audit(1558417960.720:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=803 comm="apparmor_parser"
[ 7.134648] audit: type=1400 audit(1558417960.720:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=803 comm="apparmor_parser"
[ 7.135162] audit: type=1400 audit(1558417960.720:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=808 comm="apparmor_parser"
[ 7.135571] audit: type=1400 audit(1558417960.720:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=807 comm="apparmor_parser"
[ 7.136084] audit: type=1400 audit(1558417960.724:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=810 comm="apparmor_parser"
[ 7.165332] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[ 7.165372] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[ 7.165407] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[ 7.165440] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[ 7.412511] [TTM] Zone kernel: Available graphics memory: 2011110 kiB
[ 7.412512] [TTM] Initializing pool allocator
[ 7.412516] [TTM] Initializing DMA pool allocator
[ 7.412530] nouveau 0000:01:00.0: DRM: VRAM: 512 MiB
[ 7.412531] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB
[ 7.412534] nouveau 0000:01:00.0: DRM: TMDS table version 2.0
[ 7.412535] nouveau 0000:01:00.0: DRM: DCB version 4.0
[ 7.412537] nouveau 0000:01:00.0: DRM: DCB outp 00: 01000302 00020030
[ 7.412538] nouveau 0000:01:00.0: DRM: DCB outp 01: 02000300 00000000
[ 7.412540] nouveau 0000:01:00.0: DRM: DCB outp 02: 08011392 00020020
[ 7.412541] nouveau 0000:01:00.0: DRM: DCB outp 03: 04022310 00000000
[ 7.412542] nouveau 0000:01:00.0: DRM: DCB conn 00: 00001030
[ 7.412543] nouveau 0000:01:00.0: DRM: DCB conn 01: 00002161
[ 7.412544] nouveau 0000:01:00.0: DRM: DCB conn 02: 00000200
[ 7.413500] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.413501] [drm] Driver supports precise vblank timestamp query.
[ 7.414884] nouveau 0000:01:00.0: DRM: MM: using COPY0 for buffer copies
[ 7.519626] nouveau 0000:01:00.0: DRM: allocated 1920x1080 fb: 0x60000, bo 0000000072540403
[ 7.519687] fbcon: nouveaufb (fb0) is primary device
[ 7.519765] Console: switching to colour frame buffer device 240x67
[ 7.519787] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 7.536031] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 0
[ 7.821812] IPv6: ADDRCONF(NETDEV_UP): enp4s0: link is not ready
[ 7.994641] r8169 0000:04:00.0 enp4s0: link down
[ 7.994646] r8169 0000:04:00.0 enp4s0: link down
[ 7.994709] IPv6: ADDRCONF(NETDEV_UP): enp4s0: link is not ready
[ 10.723583] r8169 0000:04:00.0 enp4s0: link up
[ 10.723594] IPv6: ADDRCONF(NETDEV_CHANGE): enp4s0: link becomes ready
[ 22.320023] usb 2-1.4: device descriptor read/64, error -110
[ 22.508017] usb 2-1.4: new high-speed USB device number 5 using ehci-pci
[ 27.696016] usb 2-1.4: device descriptor read/64, error -110
[ 30.635349] rfkill: input handler disabled
[ 43.312014] usb 2-1.4: device descriptor read/64, error -110
[ 43.420154] usb 2-1-port4: attempt power cycle
[ 44.024014] usb 2-1.4: new high-speed USB device number 6 using ehci-pci
[ 54.704011] usb 2-1.4: device not accepting address 6, error -110
[ 54.784032] usb 2-1.4: new high-speed USB device number 7 using ehci-pci
[ 65.456014] usb 2-1.4: device not accepting address 7, error -110
[ 65.456189] usb 2-1-port4: unable to enumerate USB device
gerard@PC4:~$ Comme j'ai quand même besoin de cette webcam de temps en temps je vais la rebrancgher puisque apparemment elle ne trempe pas dans l'affaire !!
Il ne reste donc de branché que : le clavier, la souris filaire et les connexions carte mère ou ports USB arrières vers le bandeau face avant, mais là je n'en sais pas plus car ce n'est pas moi qui ai installé la tour du point de vue hardware.
Je ne sais pas si ceci fait avancer le schmilblick comme dirait Coluche ??
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#13 Le 21/05/2019, à 09:00
- kholo
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
salut
lsusbte donnera des infos sur ta cam (et tout ce qui est branché en USB)
par exemple ici un dongle wifi :
Bus 001 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapterl'ID (148f:5370 dans mon exemple) correspond au nom du vendeur puis celui du matériel
ainsi tu peux faire des recherches la dessus pour voir si d'autres, avec le même matériel, ont une solution
Hors ligne
#14 Le 21/05/2019, à 11:02
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
Hello kholo
voici les réponses après avoir rebranché ma webcam
gerard@PC4:~$ lsusb
Bus 002 Device 008: ID 046d:081d Logitech, Inc. HD Webcam C510
Bus 002 Device 003: ID 1a40:0101 Terminus Technology Inc. Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 046d:c31c Logitech, Inc. Keyboard K120
Bus 001 Device 003: ID 046d:c077 Logitech, Inc. M105 Optical Mouse
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
et du coup un petit dmesg pour voir qui est coupable
Personnellement je ne sais pas trop quoi en conclure ??
[ 445.387167] usb 2-1.1: USB disconnect, device number 13
[ 491.588248] usb 2-1.4: new high-speed USB device number 18 using ehci-pci
[ 496.752151] usb 2-1.4: device descriptor read/64, error -110
[ 512.367889] usb 2-1.4: device descriptor read/64, error -110
[ 512.555877] usb 2-1.4: new high-speed USB device number 19 using ehci-pci
[ 517.743793] usb 2-1.4: device descriptor read/64, error -110
[ 533.360068] usb 2-1.4: device descriptor read/64, error -110
[ 533.468223] usb 2-1-port4: attempt power cycle
[ 534.072081] usb 2-1.4: new high-speed USB device number 20 using ehci-pci
[ 544.752243] usb 2-1.4: device not accepting address 20, error -110
[ 544.832272] usb 2-1.4: new high-speed USB device number 21 using ehci-pci
[ 555.504400] usb 2-1.4: device not accepting address 21, error -110
[ 555.504571] usb 2-1-port4: unable to enumerate USB device
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#15 Le 21/05/2019, à 17:17
- kholo
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
heu... on parle de ta webcam là mais est-ce qu'elle fonctionne ?
tu as cheese pour le vérifier
sudo apt install cheeseet vlc
créer un fichier txt
y copier
#EXTM3U
#EXTVLCOPT:v4l2-standard=
#EXTVLCOPT:input-slave=alsa://hw:0,0
#EXTVLCOPT:live-caching=300
v4l2:///dev/video0enregistrer et ajouter m3u en extension
puis ouvrir avec vlc 
NB baisser le son pour éviter le larsen !
pour revenir à ma demande de lsusb, quand c'est comme ça donc, je récupère l'ID soit sur ta ligne :
Bus 002 Device 008: ID 046d:081d Logitech, Inc. HD Webcam C510c'est
046d:081dpour vendeur:matos
et petite recherche sur le oueb pour voir qui en parle et comment !
et donc j'arrive pas loin d'ici qui m'emmène là (bon c'est pour du 12.04 mais cela donnera de bons conseils qui sont encore valable)...
mais là j'ai pas plus d'idée... je galère de temps en temps avec certains matériels...
Hors ligne
#16 Le 21/05/2019, à 18:53
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
kholo a écrit :
heu... on parle de ta webcam là mais est-ce qu'elle fonctionne ?
OUI je viens de lancer cheese et je vois toutes mes rides !!
kholo a écrit :
et vlc
créer un fichier txt
y copier#EXTM3U #EXTVLCOPT:v4l2-standard= #EXTVLCOPT:input-slave=alsa://hw:0,0 #EXTVLCOPT:live-caching=300 v4l2:///dev/video0enregistrer et ajouter m3u en extension
puis ouvrir avec vlc
je viens de le faire, j'ouvre bien avec vlc mais il ne se passe rien : écran gris et pas de son !!
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne
#17 Le 21/05/2019, à 18:58
- kholo
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
bon, l'important était de voir le bon fonctionnement de la cam...
pour vlc, peut être en l'ouvrant normalement puis
menu Media / Ouvrir un périphérique de capture /
remplir les combos :
Nom du périf vidéo et nom du périf audio en cliquant juste sur la petite flèche pour faire un sélection
puis le bouton lire en bas...
ça devrait le faire !
Hors ligne
#18 Le 21/05/2019, à 19:03
- kholo
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
... et ces problèmes ne prennent qu'une dizaines de secondes
donc l'évolution du noyau viendra peut être à bout de cela...
des fois mieux vaut ne pas trop toucher et être patient que de marcher sur trois pattes !
... pour le reste je regarde...
t'en est où du temps de démarrage ?
edit
j'ai repris le fil et je pense qu'on avancera pas plus sans prendre de risques inutiles...
tu vas pouvoir finir ton bouquin tranquillou ! 
Dernière modification par kholo (Le 21/05/2019, à 19:09)
Hors ligne
#19 Le 21/05/2019, à 20:19
- winux
Re : [RÉSOLU] Ubuntu démarrage lent suite à reboot après W10
kholo a écrit :
l'évolution du noyau viendra peut être à bout de cela...
des fois mieux vaut ne pas trop toucher et être patient que de marcher sur trois pattes !
j'ai repris le fil et je pense qu'on avancera pas plus sans prendre de risques inutiles...
tu vas pouvoir finir ton bouquin tranquillou
Hello Kholo
je suis d'accord avec tes 3 assertions et comme disait ma grand-mère, le mieux est l'ennemi du bien !!
Quant au temps de démarrage il est toujours de 42 + 8 ce qui est acceptable, même ... pour un retraité !!
Merci pour ta participation je vais mettre résolu car comme tu le dis on n'ira pas plus loin sans prendre des risques tout à fait inutiles
@+
http://i3.tinypic.com/4g8nio8.png
Livebox fibre - 980 Mbps mesurés - Triple boot : Ub 20.04 / Mint 20.2 / W10 - Ecran : Samsung 22" -
CM : Gigabyte P67A UD3 B3 - CPU : Intel Quad Core i5 3.3 GHz - GPU : nVidia Gigabyte N430
RAM : 8 Go DDR3 - SSD de 240 Go - 2 HD de 1 To chacun
Hors ligne