#26 Le 09/05/2008, à 15:03
- tophe63
Re : Comment faire fonctionner le wifi ?
ça m'a créer un dosssier et deux fichiers dans mon répertoire
le dossier s'appel doc-pack
un fichier description-pack et un autre svnversion.h, ces fichiers sont apparus aprés avoir éffectué les dernières commandes.
#27 Le 09/05/2008, à 15:05
- tophe63
Re : Comment faire fonctionner le wifi ?
Mon message prcédent correspond à ce que j'avais aprés avoir fait ce qu'ils disent sur le lien, j'essaye ce que tu m'a dit et je poste le retour.
#28 Le 09/05/2008, à 15:13
- tophe63
Re : Comment faire fonctionner le wifi ?
Voici les retour des commandes:
cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=8.04
DISTRIB_CODENAME=hardy
DISTRIB_DESCRIPTION="Ubuntu 8.04"
lsusb
Bus 007 Device 001: ID 0000:0000
Bus 006 Device 002: ID 0402:5602 ALi Corp. Video Camera Controller
Bus 006 Device 001: ID 0000:0000
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0f62:1001 Acrox Technologies Co., Ltd
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
lspci
r Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
01:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02)
01:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01)
01:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
06:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
08:00.0 VGA compatible controller: nVidia Corporation GeForce 8600M GT (rev a1)
sudo lshw -C network
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:06:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:07:00.0
logical name: eth0
version: 01
serial: 00:1d:92:50:b6:96
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.1.14 latency=0 link=yes module=r8169 multicast=yes port
lsmod
hci_usb 16540 0
ipv6 267780 10
af_packet 23812 2
rfcomm 41744 2
l2cap 25728 13 rfcomm
bluetooth 61156 5 hci_usb,rfcomm,l2cap
ppdev 10372 0
acpi_cpufreq 10796 0
cpufreq_conservative 8712 0
cpufreq_powersave 2688 0
cpufreq_ondemand 9740 2
cpufreq_stats 7104 0
freq_table 5536 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
cpufreq_userspace 5284 0
sbs 15112 0
sbshc 7680 1 sbs
container 5632 0
dock 11280 0
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
aes_i586 33536 0
dm_crypt 15364 0
dm_mod 62660 1 dm_crypt
sbp2 24072 0
parport_pc 36260 0
lp 12324 0
parport 37832 3 ppdev,parport_pc,lp
pcspkr 4224 0
serio_raw 7940 0
psmouse 40336 0
sdhci 19076 0
mmc_core 51460 1 sdhci
iTCO_wdt 13092 0
iTCO_vendor_support 4868 1 iTCO_wdt
evdev 13056 6
ath_pci 101024 0
wlan 207728 1 ath_pci
ath_hal 192592 1 ath_pci
wmi_acer 9644 0
battery 14212 0
ac 6916 0
i2c_core 24832 0
video 19856 0
output 4736 1 video
snd_hda_intel 344728 2
snd_pcm_oss 42144 0
snd_mixer_oss 17920 2 snd_pcm_oss
snd_pcm 78596 2 snd_hda_intel,snd_pcm_oss
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
snd_hwdep 10500 1 snd_hda_intel
snd_seq_dummy 4868 0
snd_seq_oss 35584 0
snd_seq_midi 9376 0
snd_rawmidi 25760 1 snd_seq_midi
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
snd_seq 54224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24836 2 snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
button 9232 0
snd 56996 13 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_hwdep,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
intel_agp 25492 0
agpgart 34760 1 intel_agp
soundcore 8800 2 snd
shpchp 34452 0
pci_hotplug 30880 1 shpchp
ext3 136712 1
jbd 48404 1 ext3
mbcache 9600 1 ext3
sr_mod 17956 0
cdrom 37408 1 sr_mod
sg 36880 0
sd_mod 30720 3
ata_piix 19588 0
usbhid 31872 0
hid 38784 1 usbhid
pata_acpi 8320 0
ahci 28420 2
ata_generic 8324 0
libata 159344 4 ata_piix,pata_acpi,ahci,ata_generic
ohci1394 33584 0
scsi_mod 151436 5 sbp2,sr_mod,sg,sd_mod,libata
ieee1394 93752 2 sbp2,ohci1394
r8169 32900 0
ehci_hcd 37900 0
uhci_hcd 27024 0
usbcore 146028 5 hci_usb,usbhid,ehci_hcd,uhci_hcd
thermal 16796 0
processor 36872 4 acpi_cpufreq,thermal
fan 5636 0
fbcon 42912 0
tileblit 3456 1 fbcon
font 9472 1 fbcon
bitblit 6784 1 fbcon
softcursor 3072 1 bitblit
fuse 50580 1
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
ifconfig
eth0 Link encap:Ethernet HWaddr 00:1d:92:50:b6:96
inet adr:192.168.1.14 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::21d:92ff:fe50:b696/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:2386 erreurs:0 :0 overruns:0 frame:0
TX packets:1591 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:1268749 (1.2 MB) Octets transmis:231595 (226.1 KB)
Interruption:217
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
uname -r -m
2.6.24-16-generic i686
cat /etc/network/interfaces
auto lo
iface lo inet loopback
#address 127.0.0.1
#netmask 255.0.0.0
#29 Le 09/05/2008, à 21:36
- tophe63
Re : Comment faire fonctionner le wifi ?
Je viens de relir plusieur fois les tutos pour installé le pilote, mais je ne vois toujours pas ce qui ne va pas, ça ne fonctionne toujours pas.
Quand je pense qu'après il y a la webcam à installer, je ne suis pas au bout de mes peines.
#30 Le 09/05/2008, à 21:40
- willy78
Re : Comment faire fonctionner le wifi ?
tu fais partie de gens qui n'ont pas de bol avec cette carte
passe par ndiswrapper!
sinon tu as utiliser quelle driver du tutos (y'a plusieurs solution)?
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#31 Le 09/05/2008, à 21:50
- tophe63
Re : Comment faire fonctionner le wifi ?
J'essaye ndiswrapper.
Depuis le tuto, j'ai utilisé le driver le plus récent, celui qui date de février 2008
#32 Le 09/05/2008, à 21:55
- willy78
Re : Comment faire fonctionner le wifi ?
essaye peut-etre avec le driver a patcher du 27-02-08
wget http://snapshots.madwifi.org/madwifi-trunk-current.tar.gz
tar xvzf madwifi-trunk-current.tar.gz
cd madwifi-trunk-r*
wget http://madwifi.org/attachment/ticket/1679/madwifi-ng-r3365.ar2425.20080227.i386.patch?format=raw -O madwifi-ng-r3365.ar2425.20080227.i386.patch
patch -p0 < madwifi-ng-r3365.ar2425.20080227.i386.patch
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#33 Le 09/05/2008, à 22:02
- tophe63.
Re : Comment faire fonctionner le wifi ?
Depuis le début j'essaye d'installer le driver pour faire fonctionner la carte wifi AR5007EG
Mais en fait je ne sais même pas si j'ai bien ce chipset là, j'ai pas vérifié, je me suis contenté de suivre le lien qu'on m'a donné.
#34 Le 09/05/2008, à 22:06
- willy78
Re : Comment faire fonctionner le wifi ?
si si c'est bien ça
06:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
regarde dans la doc
http://doc.ubuntu-fr.org/atheros_ar5007eg#pre-requis
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#35 Le 10/05/2008, à 15:54
- tophe63
Re : Comment faire fonctionner le wifi ?
J'ai vraiment tout essayé, et ça ne marche toujours pas. j'ai bien essayé ndiswrapper, en recherchant les drivers sur le CD fournis avec le PC mais je ne trouve pas de drivers atheros sur le CD, il y a un dossier qui s'appel AzureWave Wireless Lan, un autre Intel Wireless Lan, à mon avis il ne doit y avoir que ces deux dossiers qui peuvent contenir des drivers wifi, mais azurewave et atheros c'est la même chose ?
Sinon, j'ai essayé de chercher avec google, mais je ne trouve rien pour les 5007.
#36 Le 10/05/2008, à 16:00
- willy78
Re : Comment faire fonctionner le wifi ?
bon donnes quelque retour
sans infos personnes ne peux te dire si tu as merdé quelque part!
ls ~
lsmod
sudo lshw -C network
ndiswrapper -l
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#37 Le 10/05/2008, à 16:15
- tophe63
Re : Comment faire fonctionner le wifi ?
Voici les retours
ls ~
amsn_received madwifi-nr-r3366+ar5007 Musique
Bureau madwifi-nr-r3366+ar5007.tar.gz Public
Documents madwifi-nr-r3366+ar5007.tar.gz.1 Vidéos
Images Modèles
lsmod
isofs 36388 0
udf 88612 1
ipv6 267780 10
af_packet 23812 2
rfcomm 41744 2
l2cap 25728 13 rfcomm
bluetooth 61156 4 rfcomm,l2cap
ppdev 10372 0
acpi_cpufreq 10796 0
cpufreq_conservative 8712 0
cpufreq_powersave 2688 0
cpufreq_ondemand 9740 2
cpufreq_stats 7104 0
freq_table 5536 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
cpufreq_userspace 5284 0
sbs 15112 0
sbshc 7680 1 sbs
container 5632 0
dock 11280 0
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
aes_i586 33536 0
dm_crypt 15364 0
dm_mod 62660 1 dm_crypt
sbp2 24072 0
parport_pc 36260 0
lp 12324 0
parport 37832 3 ppdev,parport_pc,lp
wmi_acer 9644 0
battery 14212 0
ac 6916 0
snd_hda_intel 344728 1
sr_mod 17956 1
cdrom 37408 1 sr_mod
ndiswrapper 192920 0
video 19856 0
output 4736 1 video
i2c_core 24832 0
snd_pcm_oss 42144 0
serio_raw 7940 0
snd_mixer_oss 17920 1 snd_pcm_oss
snd_pcm 78596 2 snd_hda_intel,snd_pcm_oss
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
snd_hwdep 10500 1 snd_hda_intel
psmouse 40336 0
sdhci 19076 0
mmc_core 51460 1 sdhci
snd_seq_dummy 4868 0
snd_seq_oss 35584 0
snd_seq_midi 9376 0
snd_rawmidi 25760 1 snd_seq_midi
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
snd_seq 54224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24836 2 snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
button 9232 0
snd 56996 13 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_hwdep,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
intel_agp 25492 0
agpgart 34760 1 intel_agp
iTCO_wdt 13092 0
iTCO_vendor_support 4868 1 iTCO_wdt
evdev 13056 6
shpchp 34452 0
pci_hotplug 30880 1 shpchp
soundcore 8800 1 snd
pcspkr 4224 0
ext3 136712 1
jbd 48404 1 ext3
mbcache 9600 1 ext3
usbhid 31872 0
hid 38784 1 usbhid
ata_piix 19588 1
pata_acpi 8320 0
sg 36880 0
sd_mod 30720 4
ata_generic 8324 0
ahci 28420 3
libata 159344 4 ata_piix,pata_acpi,ata_generic,ahci
scsi_mod 151436 5 sbp2,sr_mod,sg,sd_mod,libata
ohci1394 33584 0
ieee1394 93752 2 sbp2,ohci1394
r8169 32900 0
ehci_hcd 37900 0
uhci_hcd 27024 0
usbcore 146028 5 ndiswrapper,usbhid,ehci_hcd,uhci_hcd
thermal 16796 0
processor 36872 4 acpi_cpufreq,thermal
fan 5636 0
fbcon 42912 0
tileblit 3456 1 fbcon
font 9472 1 fbcon
bitblit 6784 1 fbcon
softcursor 3072 1 bitblit
fuse 50580 3
sudo lshw -C network
*-network UNCLAIMED
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:06:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:07:00.0
logical name: eth0
version: 01
serial: 00:1d:92:50:b6:96
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.1.14 latency=0 link=yes module=r8169 multicast=yes port=twisted pair speed=100MB/s
ndiswrapper -l
autorun : invalid driver!
net5211 : driver installed
device (168C:001C) present (alternate driver: ath_pci)
netathr : driver installed
device (168C:001C) present (alternate driver: ath_pci)
#38 Le 10/05/2008, à 16:21
- willy78
Re : Comment faire fonctionner le wifi ?
ok 2 choses sont envisageable
sudo modprobe ndiswrapper
et retour de
iwlist scanning
sudo lshw -C network
ensuite pour la compilation des sources madwifi
madwifi-nr-r3366+ar5007
as tu installé le paquet build-essential?
http://fr.archive.ubuntu.com/ubuntu/poo … 1_i386.deb
Dernière modification par willy78 (Le 10/05/2008, à 16:24)
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#39 Le 10/05/2008, à 16:32
- tophe63
Re : Comment faire fonctionner le wifi ?
J'ai tapé la première commande que tu m'as donné, et ça je n'ai eu aucun retour
sinon, pour la commande iwlist scanning, j'ai
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
Et pour la commande sudo lshw -C network, j'ai:
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:06:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:07:00.0
logical name: eth0
version: 01
serial: 00:1d:92:50:b6:96
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.1.14 latency=0 link=yes module=r8169 multicast=yes port=twisted pair speed=100MB/s
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:06:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:07:00.0
logical name: eth0
version: 01
serial: 00:1d:92:50:b6:96
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.1.14 latency=0 link=yes module=r8169 multicast=yes port=twisted pair speed=100MB/s
Sinon, pour le paquet build-essential il est bien installé.
#40 Le 10/05/2008, à 16:38
- tophe63
Re : Comment faire fonctionner le wifi ?
Je viens de trouver le pilote pour windows de ma carte wifi pour essayer avec ndiswrapper, mais quelle version faut-il choisir, XP ou vista ? J'ai pris vista au hasard, Mais le pilote se présente sous la forme d'un .EXE, et non d'un .inf, il est donc inutilisabe avec linux !!
#41 Le 10/05/2008, à 16:39
- willy78
Re : Comment faire fonctionner le wifi ?
ok alors
sudo rmmod ndiswrapper
cd madwifi-nr-r3366+ar5007
make clean
make
sudo make install
et retour de
iwlist scanning
sudo lshw -C network
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#42 Le 10/05/2008, à 16:52
- tophe63
Re : Comment faire fonctionner le wifi ?
J'ai effectué les commandes que tu m'a induiqué, j'ai eu ceci qui s'est affiché :
rapper
ERROR: Module ndiswrapper does not exist in /proc/modules
tof@tof-laptop:~/Documents/Patchs/madwifi-trunk-r3620-20080508$ cd madwifi-nr-r3366+ar5007
bash: cd: madwifi-nr-r3366+ar5007: Aucun fichier ou dossier de ce type
tof@tof-laptop:~/Documents/Patchs/madwifi-trunk-r3620-20080508$ make clean
for i in ath/ ath_hal/ ath_rate/ net80211/; do \
make -C $i clean; \
done
make[1]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath'
rm -f *~ *.o *.ko *.mod.c .*.cmd
rm -f .depend .version .*.o.flags .*.o.d
rm -rf .tmp_versions
make[1]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath'
make[1]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal'
rm -f *~ *.o *.ko *.mod.c uudecode .*.cmd
rm -f .depend .version .*.o.flags .*.o.d
rm -rf .tmp_versions
make[1]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal'
make[1]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate'
for i in amrr/ onoe/ sample/ minstrel/; do \
make -C $i clean; \
done
make[2]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/amrr'
rm -f *~ *.o *.ko *.mod.c
rm -f .depend .version .*.o.flags .*.o.d .*.o.cmd .*.ko.cmd
rm -rf .tmp_versions
make[2]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/amrr'
make[2]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/onoe'
rm -f *~ *.o *.ko *.mod.c
rm -f .depend .version .*.o.flags .*.o.d .*.o.cmd .*.ko.cmd
rm -rf .tmp_versions
make[2]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/onoe'
make[2]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/sample'
rm -f *~ *.o *.ko *.mod.c
rm -f .depend .version .*.o.flags .*.o.d .*.o.cmd .*.ko.cmd
rm -rf .tmp_versions
make[2]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/sample'
make[2]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/minstrel'
rm -f *~ *.o *.ko *.mod.c
rm -f .depend .version .*.o.flags .*.o.d .*.o.cmd .*.ko.cmd
rm -rf .tmp_versions
make[2]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/minstrel'
make[1]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate'
make[1]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211'
rm -f *~ *.o *.ko *.mod.c
rm -f .depend .version .*.o.flags .*.o.d .*.o.cmd .*.ko.cmd
rm -rf .tmp_versions
make[1]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211'
make -C ./tools clean
make[1]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/tools'
rm -f athstats 80211stats athkey athchans athctrl athdebug 80211debug wlanconfig core a.out
make[1]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/tools'
rm -rf .tmp_versions
rm -f *.symvers svnversion.h
tof@tof-laptop:~/Documents/Patchs/madwifi-trunk-r3620-20080508$ make
Checking requirements... ok.
Checking kernel configuration... ok.
make -C /lib/modules/2.6.24-16-generic/build SUBDIRS=/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508 modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.24-16-generic'
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath/if_ath.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath/if_ath_radar.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath/if_ath_pci.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath/ath_pci.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/ah_os.o
HOSTCC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/uudecode
UUDECODE /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/i386-elf.hal.o
# Replace as many hashed names as possible with meaningful
# ones in the symbol table of the binary kernel module for HAL.
objcopy \
`cat /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/../scripts/hal_unmangle.objcopy` \
/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/i386-elf.hal.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/ath_hal.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/amrr/amrr.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/amrr/ath_rate_amrr.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/minstrel/minstrel.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/minstrel/ath_rate_minstrel.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/onoe/onoe.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/onoe/ath_rate_onoe.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/sample/sample.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/sample/ath_rate_sample.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/if_media.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_skb.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_beacon.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_crypto.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_crypto_none.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_input.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_node.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_output.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_power.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_proto.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_scan.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_wireless.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_linux.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_monitor.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_rate.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_acl.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_crypto_ccmp.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_scan_ap.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_scan_sta.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_crypto_tkip.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_crypto_wep.o
CC [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/ieee80211_xauth.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_wep.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_tkip.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_ccmp.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_acl.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_xauth.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_scan_sta.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_scan_ap.o
Building modules, stage 2.
MODPOST 14 modules
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath/ath_pci.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath/ath_pci.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/ath_hal.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_hal/ath_hal.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/amrr/ath_rate_amrr.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/amrr/ath_rate_amrr.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/minstrel/ath_rate_minstrel.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/minstrel/ath_rate_minstrel.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/onoe/ath_rate_onoe.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/onoe/ath_rate_onoe.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/sample/ath_rate_sample.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/ath_rate/sample/ath_rate_sample.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_acl.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_acl.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_ccmp.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_ccmp.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_scan_ap.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_scan_ap.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_scan_sta.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_scan_sta.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_tkip.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_tkip.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_wep.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_wep.ko
CC /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_xauth.mod.o
LD [M] /home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/net80211/wlan_xauth.ko
make[1]: Leaving directory `/usr/src/linux-headers-2.6.24-16-generic'
make -C ./tools all || exit 1
make[1]: Entering directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/tools'
gcc -o athstats -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal -I../ath athstats.c
gcc -o 80211stats -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal 80211stats.c
gcc -o athkey -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal athkey.c
gcc -o athchans -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal athchans.c
gcc -o athctrl -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal athctrl.c
gcc -o athdebug -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal athdebug.c
gcc -o 80211debug -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal 80211debug.c
gcc -o wlanconfig -g -O2 -Wall -I. -I../hal -I.. -I../ath_hal wlanconfig.c
make[1]: Leaving directory `/home/tof/Documents/Patchs/madwifi-trunk-r3620-20080508/tools'
tof@tof-laptop:~/Documents/Patchs/madwifi-trunk-r3620-20080508$ sudo make install
Puis voici le retour des autres commandes
donc, pour la commande iwlist scanning, j'ai
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
Et pour la commande sudo lshw -C network, j'ai:
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:06:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: latency=0
*-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:07:00.0
logical name: eth0
version: 01
serial: 00:1d:92:50:b6:96
size: 100MB/s
capacity: 1GB/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.1.14 latency=0 link=yes module=r8169 multicast=yes port=twisted pair speed=100MB/s
#43 Le 10/05/2008, à 18:33
- tophe63
Re : Comment faire fonctionner le wifi ?
Je ne sais plus quoi faire, je ne veux plus entendre parler de cette m**** de Windows qui chope 50 virus par jour, mais Linux est super chiant à faire fonctionner, je crois que je vais être obliger d'économiser un peu et d'acheter un mac pour espérer avoir un ordinateur qui soit à la fois fiable et facile d'utilisation.
Plus je lis les messages sur ce forum et plus je me rend compte que Linux n'est pas encore au point avec le wifi.
#44 Le 10/05/2008, à 20:17
- tophe63
Re : Comment faire fonctionner le wifi ?
Bon allé, c'est décidé, je supprime kubuntu de mon PC, et je vais une dernière tentative, mais avec ubuntu cette fois-ci. Vous allez me dire c'est la même chose, mais tout le monde dit que c'est bien. Si ça ne marche toujours pas, je ramène le PC chez le vendeur.
#45 Le 10/05/2008, à 20:20
- willy78
Re : Comment faire fonctionner le wifi ?
tu as rebooter après le make install?
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#46 Le 10/05/2008, à 20:36
- tophe63
Re : Comment faire fonctionner le wifi ?
Oui, je n'ai même plus compté le nombre de make instal et de redemarrages que j'ai effectué.
#47 Le 11/05/2008, à 10:27
- tophe63
Re : Comment faire fonctionner le wifi ?
Je viens d'essayer avec un CD live de Ubuntu, voici le message que j'ai pour mes périphériques.
Des pilotes propriétaires sont actuellement utilisés afin d'assurer le bon fonctionnement de cet ordinateur.
Le code source des pilotes propriétaires n'est pas librement accessible et modifiable par les dévelopeurs de ubuntu. Leur utilisation est risquée car la société qui produit ces pilotes ne les a conçus que pour certains types de matériel, et les mises à jour de sécurité qui y sont apportées dépendent uniquement de son bon vouloir. Ubuntu ne peut pas réparer ou améliorer ces pilotes.
En clair, ça veut dire quoi ? Que ce n'est pas la peine que j'essaye, que mon PC ne peut pas tourner avec Ubuntu ?
#48 Le 11/05/2008, à 14:21
- willy78
Re : Comment faire fonctionner le wifi ?
mais j'ai moi aussi une atheros et elle marche très bien sinon pour la tienne pratiquement arrive a la faire marcher et la je ne sais pas pourquoi!
Depuis Hardy d'ailleurs c'est le flou artistique!
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#49 Le 11/05/2008, à 18:32
- tophe63
Re : Comment faire fonctionner le wifi ?
J'ai enfin résolu mon problème de wifi:D
J'ai tout simplement changé de distribution, j'ai testé mandriva et mon wifi à fonctionné du premier coup.
Je vais donc supprimer Kubuntu pour faire place à Madriva, mais il ne restera plus qu'à voir si les autres périphériques fonctionnent.
#50 Le 11/05/2008, à 18:34
- tophe63
Re : Comment faire fonctionner le wifi ?
Merci pour votre aide à tous.