#1 Le 07/05/2019, à 21:36
- Xaxou
[Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Bonjour,
Je tourne sous Ubuntu 18.04 LTS depuis décembre. Il est vraisemblable que la version 18.10 se soit installée assez vite via une mise à jour automatique. Tout tournait bien et j'avais notamment configuré mon clavier français, mon fond d’écran, ma barre d'application...
Ce week-end, j'ai du exécuter manuellement un fsck /dev/sda2 lors du démarrage (c'est malheureusement une manip que mon ordinateur me demande un peu trop régulièrement avant de démarrer Ubuntu). Depuis, ma session est celle "configurée de base" : le clavier est en qwerty, le fond d’écran a disparu, etc. Et bien que je sois administrateur, impossible de modifier ces caractéristiques. J'ai essayé de lancer un recovery sur différentes versions antérieures, rien n'y fait. J'ai toutefois constaté que ma version actuelle est la 19.04 : peut-être tout ceci est-il lié, je ne peux pas le dire.
Quelqu'un a-t-il rencontré un problème similaire ? Idéalement, quelqu'un sait-il le résoudre ?
Merci par avance,
Xavier
Dernière modification par Xaxou (Le 20/05/2019, à 22:54)
Hors ligne
#2 Le 07/05/2019, à 23:02
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Hum, faudrait voir l'état du disque:
sudo apt-get install --no-install-recommends smartmontools
sudo smartctl -s on -a /dev/sda
Hors ligne
#3 Le 08/05/2019, à 10:37
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Bonjour Naziel,
Merci beaucoup pour ton retour : penses-tu que ça puisse être en lien avec l'absence de chargement de mes paramètres de configuration ? J'essaie de faire une réponse lisible, j'anticipe déja ma satisfaction quand je récupèrerai un clavier azerty !
Je commence par la ligne de commande que tu m'as indiquée, puis je fais pareil avec /dev/sda2 qui correspond au message d'erreur que j'ai régulièrement.
Merci encore !
Xavier
~$ sudo smartctl -s on -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 10:22:47 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 110
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 348
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 133701
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 023 016 000 Old_age Always - 23 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 094 091 000 Old_age Always - 102
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 476
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 263
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 413
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 476
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 45279
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
~$ sudo smartctl -s on -a /dev/sda2
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 10:27:23 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 110
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 348
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 133749
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 024 016 000 Old_age Always - 24 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 094 091 000 Old_age Always - 102
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 477
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 264
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 413
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 477
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 45279
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
Hors ligne
#4 Le 08/05/2019, à 10:42
- xubu1957
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#5 Le 08/05/2019, à 10:49
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Bonjour,
Je ne sais pas bien pourquoi j'ai une version "non-officielle" mais je n'ai aucune réticence a passer a une version plus officielle, surtout si ça peut régler mon problème... Toutefois, je ne sais pas du tout comment faire, pouvez-vous SVP m'indiquer par étape comment procéder ?
Merci beaucoup,
Xavier
Hors ligne
#6 Le 08/05/2019, à 10:55
- xubu1957
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Montre les noyaux présents :
echo; dpkg -l | grep -Ei "linux-(g|h|i|lo|mo|si|t)" | grep -v ^rc | sort -k3 | awk '{print $1,$2,$3,$4}' | column -s" " -t ; echo ; uname -mr
et le sources.list :
find /etc/apt -type f -name '*.list*' -exec bash -c 'echo -e "\n$1\n"; [[ $1 = *".list" ]] && nl -ba "$1"' _ '{}' \;
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#7 Le 08/05/2019, à 10:58
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Pour les noyaux présents :
~$ echo; dpkg -l | grep -Ei "linux-(g|h|i|lo|mo|si|t)" | grep -v ^rc | sort -k3 | awk '{print $1,$2,$3,$4}' | column -s" " -t ; echo ; uname -mr
ii binutils-x86-64-linux-gnu 2.30-21ubuntu1~18.04 amd64
ii linux-headers-4.15.0-43 4.15.0-43.46 all
ii linux-modules-4.15.0-43-generic 4.15.0-43.46 amd64
ii linux-modules-extra-4.15.0-43-generic 4.15.0-43.46 amd64
ii linux-headers-4.15.0-43-generic 4.15.0-43.46 amd64
ii linux-image-4.15.0-43-generic 4.15.0-43.46 amd64
ii linux-generic 4.15.0.45.47 amd64
ii linux-signed-generic 4.15.0.45.47 amd64
ii linux-headers-generic 4.15.0.45.47 amd64
ii linux-image-generic 4.15.0.45.47 amd64
ii linux-headers-4.15.0-45 4.15.0-45.48 all
ii linux-modules-4.15.0-45-generic 4.15.0-45.48 amd64
ii linux-modules-extra-4.15.0-45-generic 4.15.0-45.48 amd64
ii linux-headers-4.15.0-45-generic 4.15.0-45.48 amd64
ii linux-image-4.15.0-45-generic 4.15.0-45.48 amd64
ii linux-headers-4.19.5-041905 4.19.5-041905.201811271131 all
ii linux-modules-4.19.5-041905-generic 4.19.5-041905.201811271131 amd64
ii linux-headers-4.19.5-041905-generic 4.19.5-041905.201811271131 amd64
ii linux-image-unsigned-4.19.5-041905-generic 4.19.5-041905.201811271131 amd64
4.19.5-041905-generic x86_64
et pour le sources.list :
~$ find /etc/apt -type f -name '*.list*' -exec bash -c 'echo -e "\n$1\n"; [[ $1 = *".list" ]] && nl -ba "$1"' _ '{}' \;
/etc/apt/sources.list.save
/etc/apt/sources.list
1 # deb cdrom:[Ubuntu 18.04.1 LTS _Bionic Beaver_ - Release amd64 (20180725)]/ bionic main restricted
2
3 # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to
4 # newer versions of the distribution.
5 deb http://fr.archive.ubuntu.com/ubuntu/ bionic main restricted
6 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic main restricted
7
8 ## Major bug fix updates produced after the final release of the
9 ## distribution.
10 deb http://fr.archive.ubuntu.com/ubuntu/ bionic-updates main restricted
11 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic-updates main restricted
12
13 ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu
14 ## team. Also, please note that software in universe WILL NOT receive any
15 ## review or updates from the Ubuntu security team.
16 deb http://fr.archive.ubuntu.com/ubuntu/ bionic universe
17 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic universe
18 deb http://fr.archive.ubuntu.com/ubuntu/ bionic-updates universe
19 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic-updates universe
20
21 ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu
22 ## team, and may not be under a free licence. Please satisfy yourself as to
23 ## your rights to use the software. Also, please note that software in
24 ## multiverse WILL NOT receive any review or updates from the Ubuntu
25 ## security team.
26 deb http://fr.archive.ubuntu.com/ubuntu/ bionic multiverse
27 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic multiverse
28 deb http://fr.archive.ubuntu.com/ubuntu/ bionic-updates multiverse
29 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic-updates multiverse
30
31 ## N.B. software from this repository may not have been tested as
32 ## extensively as that contained in the main release, although it includes
33 ## newer versions of some applications which may provide useful features.
34 ## Also, please note that software in backports WILL NOT receive any review
35 ## or updates from the Ubuntu security team.
36 deb http://fr.archive.ubuntu.com/ubuntu/ bionic-backports main restricted universe multiverse
37 # deb-src http://fr.archive.ubuntu.com/ubuntu/ bionic-backports main restricted universe multiverse
38
39 ## Uncomment the following two lines to add software from Canonical's
40 ## 'partner' repository.
41 ## This software is not part of Ubuntu, but is offered by Canonical and the
42 ## respective vendors as a service to Ubuntu users.
43 # deb http://archive.canonical.com/ubuntu bionic partner
44 # deb-src http://archive.canonical.com/ubuntu bionic partner
45
46 deb http://security.ubuntu.com/ubuntu bionic-security main restricted
47 # deb-src http://security.ubuntu.com/ubuntu bionic-security main restricted
48 deb http://security.ubuntu.com/ubuntu bionic-security universe
49 # deb-src http://security.ubuntu.com/ubuntu bionic-security universe
50 deb http://security.ubuntu.com/ubuntu bionic-security multiverse
51 deb https://dl.winehq.org/wine-builds/ubuntu/ bionic main
52 # deb-src https://dl.winehq.org/wine-builds/ubuntu/ bionic main
53 # deb-src https://dl.winehq.org/wine-builds/ubuntu/ bionic main
54 # deb-src https://dl.winehq.org/wine-builds/ubuntu/ bionic main
55 # deb-src https://dl.winehq.org/wine-builds/ubuntu/ bionic main
/etc/apt/sources.list.d/microsoft-prod.list
1 deb [arch=amd64] https://packages.microsoft.com/ubuntu/18.04/prod bionic main
/etc/apt/sources.list.d/andreas-diesner-ubuntu-garminplugin-bionic.list
/etc/apt/sources.list.d/microsoft-prod.list.save
/etc/apt/sources.list.d/andreas-diesner-ubuntu-garminplugin-bionic.list.save
/etc/apt/sources.list.d/teejee2008-ubuntu-ppa-bionic.list.save
/etc/apt/sources.list.d/teejee2008-ubuntu-ppa-bionic.list
Hors ligne
#8 Le 08/05/2019, à 11:01
- xubu1957
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
/etc/apt/sources.list.d/teejee2008-ubuntu-ppa-bionic.list
C'est le PPA d'ubuntu_kernel_upgrade_utility
On va attendre l'avis de Naziel.
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#9 Le 08/05/2019, à 11:09
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Je vais sûrement être moins présent pendant une semaine.
Le ssd est comme neuf visiblement.
Mais là, tu es sûrement encore sur la version 18.04, le noyau 4.19 vient à mon avis d'ukuu. Je suis convaincu que le problème vient de là.
Tu peux faire shift au démarrage du pc avant le démarrage d'ubuntu afin d'avoir un menu (il s'appelle grub), tu fais options avancées et tu choisis un noyau 4.15 ni recovery ni upstart, et dire si ça fonctionne mieux
Hors ligne
#10 Le 08/05/2019, à 15:22
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Bonjour à vous deux,
J'ai lancé la version 4.15.0.45 generic sans recovery, mais au bout du compte ça ne fait malheureusement pas de différence.
Une fois sous Ubuntu, quand je vais dans "A propos", c'est bien "Ubuntu 18.04.2 LTS" qui s'affiche. Pas de référence a la version du noyau.
Pour information, j'ai fait "Echap" au démarrage car "Shift" ne menait a rien. Et comme annonce par Naziel, le menu s'appelait bien Grub. Je pense que ça n'a aucune importance dans cette démarche, mais à tout hasard je préfère préciser...
Je vais tenter de passer par le "Software Updater".
En tout cas merci beaucoup pour votre aide... et bonnes vacances (?) Naziel.
Xavier
Dernière modification par Xaxou (Le 08/05/2019, à 15:23)
Hors ligne
#11 Le 08/05/2019, à 16:22
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Hum, j'ai peut être dit des bêtises sur la lecture du rapport smart. https://www.smartmontools.org/ticket/724 donne quelques infos, faudrait essayer une version plus récente de smartmontools pour que ce soit lisible
Heu non, je suis pas en vacances. C'est plutôt l'inverse en ce moment.
Hors ligne
#12 Le 08/05/2019, à 17:05
- ylag
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Salut,
Pour information, j'ai fait "Echap" au démarrage car "Shift" ne menait a rien.
"Echap" => pour un boot UEFI
"Shift" => pour un boot BIOS legacy
A+
Hors ligne
#13 Le 08/05/2019, à 17:09
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Merci ylag, j'avais jamais compris pourquoi des fois c'était échap et des fois shift (je pensais que c'était échap pour les pc pour qui l'accès au bios se fait avec shift)
Hors ligne
#14 Le 08/05/2019, à 17:14
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
D'accord ! J'ai téléchargé le fichier .txt mais je ne comprends pas la consigne "Could you place add this hardrive to drivedb.h". Faut-il que je le mette dans le répertoire de drivedb.h ou que je l'ajoute au sein du fichier drivedb.h ?
En outre, il s'agit d'un emplacement ou je ne peux pas copier-coller. Puis-je passer sans risque par un "sudo -H gedit" ou similaire ?
Hors ligne
#15 Le 08/05/2019, à 17:14
- ylag
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
@Naziel:
Salut,
Enfin, il me semble que ce soit le cas; je n'arrive pas à retrouver l'article qui en faisait mention !
A+
Dernière modification par ylag (Le 08/05/2019, à 17:16)
Hors ligne
#16 Le 08/05/2019, à 17:29
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Oh non Xaxou, attends, je te donne les commandes: télécharge smartmontools via https://sourceforge.net/projects/smartm … z/download tu le décompresses dans le dossier personnel puis
cd smartmontools-7.0
./configure
make
sudo make install
@ylag: c'est déjà bien plus plausible que ce que je supposais.
Hors ligne
#17 Le 08/05/2019, à 19:21
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Merci beaucoup pour les lignes de commandes ! Je ne comprends pas ce que je fais, mais au moins je le fais bien ! Enfin... je crois. Donc :
~$ sudo smartctl -s on -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 19:17:34 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 111
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 351
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 136885
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 021 016 000 Old_age Always - 21 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 097 091 000 Old_age Always - 104
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 490
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 270
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 426
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 490
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 46394
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
Ou encore pour /dev/sda2 - même si le résultat ressemble :
~$ sudo smartctl -s on -a /dev/sda2
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 19:19:59 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 111
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 351
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 136917
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 021 016 000 Old_age Always - 21 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 097 091 000 Old_age Always - 104
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 490
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 270
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 426
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 490
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 46394
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
Je ne doute pas que vous compreniez ces lignes... Pour moi c'est hermétique !
Dernière modification par Xaxou (Le 08/05/2019, à 19:22)
Hors ligne
#18 Le 08/05/2019, à 19:31
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Les commandes que je t'ai indiqué permettent d'utiliser une version plus récente de smartmontools ce qui permet d'avoir les noms de tous les attributs.
Ne fais pas sudo smartctl -s on -a /dev/sda2 parce que /dev/sda2 est une partition, et cela ne s'applique uniquement aux disques, donc ici /dev/sda.
Tu n'as pas donné les retours de commandes, du coup je ne peux pas savoir s'il y a eu une erreur.
Tu peux donner
sudo /usr/local/sbin/smartctl -s on -a /dev/sda
Hors ligne
#19 Le 08/05/2019, à 21:54
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Et moi qui disais que ça me permettait de faire les choses bien ! J'en suis pour mon compte ! Que sont les "retours de commande" que je n'ai pas donnés ? Je note que c'est une version 7.0 de smartctl, alors qu'avant c’était la 6.6. Je suppose que l'installation a fonctionné et que je lance le bon programme, à défaut de fournir les bonnes informations ?
Du coup je relance le script :
~$ sudo /usr/local/sbin/smartctl -s on -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 21:45:38 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 111
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 352
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 136997
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 020 016 000 Old_age Always - 20 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 094 091 000 Old_age Always - 94
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 490
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 270
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 427
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 490
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 46633
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
Hors ligne
#20 Le 08/05/2019, à 22:01
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
... il suffisait de lire ta signature. Donc :
xavier@elrond:~$ sudo /usr/local/sbin/smartctl -s on -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 22:00:08 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 112
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 352
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 137125
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 021 016 000 Old_age Always - 21 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 094 091 000 Old_age Always - 95
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 491
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 270
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 427
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 491
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 46637
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
xavier@elrond:~$
Hors ligne
#21 Le 08/05/2019, à 22:24
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Pas de problème, je parlais des retours de commande du post 16, mais ça n'a pas marché au final, il y a toujours les attributs inconnus.
Peut être
sudo /usr/local/sbin/update-smart-drivedb
sudo /usr/local/sbin/smartctl -s on -a /dev/sda
Hors ligne
#22 Le 08/05/2019, à 22:29
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Oups... Ca va mieux quand je tiens compte du qwerty pour donner mon mot de passe !
xavier@elrond:~$ sudo /usr/local/sbin/update-smart-drivedb
[sudo] Mot de passe de xavier :
Désolé, essayez de nouveau.
[sudo] Mot de passe de xavier :
/usr/local/share/smartmontools/drivedb.h updated from branches/RELEASE_7_0_DRIVEDB
xavier@elrond:~$ sudo /usr/local/sbin/update-smart-drivedb
/usr/local/share/smartmontools/drivedb.h is already up to date
xavier@elrond:~$
xavier@elrond:~$ sudo /usr/local/sbin/smartctl -s on -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.5-041905-generic] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HFS128G3BTND-N210A
Serial Number: EJ84N594811004O5P
Firmware Version: 30001P10
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed May 8 22:27:35 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 166 166 006 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 253 100 036 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 112
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 352
100 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 137413
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 81
171 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 4
174 Unknown_Attribute 0x0030 100 100 000 Old_age Offline - 22
177 Wear_Leveling_Count 0x0032 100 100 001 Old_age Always - 4
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 000 Old_age Always - 81
180 Unused_Rsvd_Blk_Cnt_Tot 0x0032 098 098 010 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 253 253 000 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 253 253 000 Old_age Always - 0
183 Runtime_Bad_Block 0x0032 253 253 000 Old_age Always - 0
184 End-to-End_Error 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 021 016 000 Old_age Always - 21 (Min/Max 14/42)
195 Hardware_ECC_Recovered 0x0032 253 253 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 253 253 000 Old_age Always - 0
201 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
204 Soft_ECC_Correction 0x000e 094 091 000 Old_age Always - 97
231 Temperature_Celsius 0x0033 253 253 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 001 Old_age Always - 4
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 492
241 Total_LBAs_Written 0x0032 100 100 --- Old_age Always - 270
242 Total_LBAs_Read 0x0032 100 100 --- Old_age Always - 427
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 492
250 Read_Error_Retry_Rate 0x0032 100 100 --- Old_age Always - 46641
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
xavier@elrond:~$
Hors ligne
#23 Le 08/05/2019, à 22:31
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Bon, on aura pas les attributs inconnus. Donc on ne peut pas être sûr de l'état du ssd malheureusement
Hors ligne
#24 Le 08/05/2019, à 22:48
- Xaxou
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Bon, on aura pas les attributs inconnus. Donc on ne peut pas être sûr de l'état du ssd malheureusement
Ce qui signifie que je n'ai pas d'espoir significatif de retour à la normale pour ma session ?
Heu non, je suis pas en vacances. C'est plutôt l'inverse en ce moment.
En tout cas merci pour le temps consacré à ces nombreuses tentatives et pour tes explications très claires ; et bon courage pour tes "non-vacances" !
Hors ligne
#25 Le 08/05/2019, à 22:53
- Nuliel
Re : [Résolu] Problème de personnalisation de session Ubuntu 18.04.2 LTS
Pour l'azerty, fais
setxkbmap fr
ça devrait te redonner un agencement azerty
Mais être obligé de faire des fsck à répétition vient en général d'un disque dur/ssd défectueux. Mais là je peux pas en être sûr avec les attributs manquants
Hors ligne