Pages : 1
#1 Le 07/11/2019, à 01:59
- zouzou
initramfs au démarrage
Bonjour, bonsoir
Je viens vers vous car je commence vraiment à désespérer !
Je m'explique, depuis quelques jours mon PC bloque au démarrage avec le message suivant :
/dev/sda2 : UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
(i.e. , without -a or -p options)
fsck exited with status code 4
The root filesystem on /dev/sda2 required manual fsck
BusyBox v1.27.2 (Ubuntu 1:1.27.2-2ubuntu3.2) built-in shell (ash)
Enter 'help' for a list of built-in commands.
( initramfs) _
Suite à ça, j'ai fais les manipulations suivantes :
fsck -y /dev/sda2
fsck - c /dev/sda2
fsck -yv /dev/sda2
la dernière à plutôt fonctionné, mais pas à chaque fois, puis le problème persiste donc est-ce-qu'il y aurait une autre commande à effectuer?
Merci de m'avoir lue, et j'espère que quelqu'un saura m'aider.
Hors ligne
#2 Le 07/11/2019, à 07:19
- moko138
Re : initramfs au démarrage
Oui,
fsck -yfv /dev/sda2
(note le -f en plus)
était la bonne réponse logicielle à
/dev/sda2 : (...) RUN fsck MANUALLY.
Mais...
Si tu éteins ton ordi normalement et que le message revient régulièrement, il est à parier que c'est ton disque qui est sur le point de matériellement défuncter.
Si c'est bien le cas, IL NE FAUT PAS FAIRE DE FSCK ! Parce qu'un fsck dans ces conditions diminue tes chances de récupérer tes données.
Pour vérifier l'état matériel du disque
En session live_USB ou live DVD :
a) Installer l'utilitaire permettant de voir l'état du disque :
sudo apt-get install --no-install-recommends smartmontools
.
b) Repérer la lettre X exacte attribuée au disque /dev/sdX (elle peut changer entre deux branchements ou démarrages) :
sudo lsblk -o name,fstype,label,size,mountpoint -e 7,11
.
c) Recueillir les données SMART :
en remplaçant X par la lettre trouvée précédemment, faire sans ajouter de chiffre :
sudo smartctl -s on -S on -o off -a /dev/sdX
et en donner le retour complet et entre balises-code.
L'option -o off ci-dessus s'impose quand on soupçonne le mauvais état matériel du disque.
( Sinon, on pourrait mettre -o on ).
Dernière modification par moko138 (Le 07/11/2019, à 07:22)
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#3 Le 07/11/2019, à 10:06
- zouzou
Re : initramfs au démarrage
Bonjour Moko,
Merci d'avoir répondu, je vais essayé ça dans la journée (faut que je retrouve le live cd !! )
Bien expliqué en détail, je n'en attendais pas autant lol
Je vous dirais ce qu'il en ait.
Bonne journée et encore merci
Hors ligne
#4 Le 10/11/2019, à 02:37
- zouzou
Re : initramfs au démarrage
re Moko,
désolée de ne pas avoir répondu plus tôt, mais quelques soucis perso en ce moment.
Alors du coup concernant mon pc, depuis que j'ai posté le message, comme par hasard il n'a plus fait ce fameux message ' initramfs' mais le jour où ça recommence je ferais les manipulations qui m'ont été conseillées et je vous dirais s'il y a du nouveau.
Je pense que vous m'avez envoyé de bonnes ondes, c'est pour cela que ça fonctionne maintenant ! !
Encore merci pour votre réponse
Hors ligne
#5 Le 10/11/2019, à 04:17
- moko138
Re : initramfs au démarrage
Non, il ne faut pas attendre !
Et puisque ton système démarre, tu peux installer smartmontools dans ton système.
N'ATTENDS PAS !
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#6 Le 11/11/2019, à 23:18
- zouzou
Re : initramfs au démarrage
Bonsoir Moko
voilà j'ai fais les commandes que tu m'as conseillé, je ne comprends pas tout sur les résultats, si tu peux m'éclairer quand tu auras un moment.
Merci en tout cas pour ton aide
Voici les résultats des commandes ci-dessous
sandy@sandyzou:~$ sudo smartctl -s on -S on -o off -a /dev/sda2
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-66-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, [url=http://www.smartmontools.org]www.smartmontools.org[/url]
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 75F1C20AT
LU WWN Device Id: 5 000039 66330379a
Firmware Version: AX003J
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Nov 11 22:13:09 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
SMART Attribute Autosave Enabled.
SMART Automatic Offline Testing Disabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 244) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1684
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 6454
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 3488
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 7919
10 Spin_Retry_Count 0x0033 228 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3692
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 534
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 177
193 Load_Cycle_Count 0x0032 089 089 000 Old_age Always - 117961
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 29 (Min/Max 14/46)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 322
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 760
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 085 085 000 Old_age Always - 6390
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 254
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 1112 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1112 occurred at disk power-on lifetime: 7882 hours (328 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 60 c7 1a 40 Error: UNC at LBA = 0x001ac760 = 1754976
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 60 c7 1a 40 00 01:11:59.385 READ FPDMA QUEUED
61 08 f0 18 1d 58 40 00 01:11:59.374 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:11:59.133 FLUSH CACHE EXT
61 08 70 10 84 19 40 00 01:11:59.132 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:11:59.132 FLUSH CACHE EXT
Error 1111 occurred at disk power-on lifetime: 7882 hours (328 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 48 60 c7 1a 40 Error: UNC at LBA = 0x001ac760 = 1754976
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 48 60 c7 1a 40 00 01:11:55.297 READ FPDMA QUEUED
61 48 40 c8 83 19 40 00 01:11:55.289 WRITE FPDMA QUEUED
61 38 38 b0 3e a0 40 00 01:11:53.561 WRITE FPDMA QUEUED
61 10 30 88 cb 9c 40 00 01:11:53.561 WRITE FPDMA QUEUED
61 18 28 28 bf 9c 40 00 01:11:53.561 WRITE FPDMA QUEUED
Error 1110 occurred at disk power-on lifetime: 7882 hours (328 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 60 c7 1a 40 Error: UNC at LBA = 0x001ac760 = 1754976
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 60 c7 1a 40 00 01:10:39.001 READ FPDMA QUEUED
61 08 f0 40 62 ea 40 00 01:10:38.988 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:10:38.808 FLUSH CACHE EXT
61 08 e0 38 37 19 40 00 01:10:38.808 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:10:38.687 FLUSH CACHE EXT
Error 1109 occurred at disk power-on lifetime: 7882 hours (328 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 f0 60 c7 1a 40 Error: UNC at LBA = 0x001ac760 = 1754976
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 f0 60 c7 1a 40 00 01:10:34.821 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:10:32.462 FLUSH CACHE EXT
61 08 e0 38 36 19 40 00 01:10:32.462 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:10:32.392 FLUSH CACHE EXT
61 40 d0 f8 34 19 40 00 01:10:32.391 WRITE FPDMA QUEUED
Error 1108 occurred at disk power-on lifetime: 7882 hours (328 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 b8 60 c7 1a 40 Error: UNC at LBA = 0x001ac760 = 1754976
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 b8 60 c7 1a 40 00 01:08:48.384 READ FPDMA QUEUED
61 08 b0 98 1b 58 40 00 01:08:48.290 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:08:48.183 FLUSH CACHE EXT
61 08 a0 90 ee 18 40 00 01:08:48.183 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 01:08:48.152 FLUSH CACHE EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 615 -
# 2 Short offline Completed without error 00% 615 -
# 3 Short offline Completed without error 00% 36 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Dernière modification par Nuliel (Le 11/11/2019, à 23:21)
Hors ligne
#7 Le 11/11/2019, à 23:24
- Nuliel
Re : initramfs au démarrage
Il est URGENT de sauvegarder les données sur un autre support, ton disque dur part en vrille: 3488 secteurs réalloués, 760 en attente de l'être, c'est beaucoup!
Sinon bizarre que smartctl râle pas alors que tu l'as passé sur une partition et non le disque (/dev/sda2 au lieu de /dev/sda)
Dernière modification par Nuliel (Le 11/11/2019, à 23:25)
Hors ligne
#8 Le 12/11/2019, à 01:39
- moko138
Re : initramfs au démarrage
Oui, disque moribond. Et qui a été secoué :
191 G-Sense_Error_Rate - 534
/!\ Priorité à la sauvegarde des données sur un support sain.
= =
Naziel,
Le nombre (sdaN) perturbe smartctl quand il y a un adaptateur usb à identifier.
Seulement dans ce cas, jusqu'à plus ample informé. Cf. ./viewtopic.php?pid=21841415#p21841415 (et la Doc, si ma note n'a pas été supprimée).
Et non, smartctl, même perturbé, ne proteste - malheureusement - jamais quand on ajoute un numéro de partition.
Tu trouveras dans le man des détails sur le seul cas où on ajoute un chiffre (ex /dev/sg0 ) : derrière un contrôleur RAID.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#9 Le 12/11/2019, à 14:59
- zouzou
Re : initramfs au démarrage
bonjour,
Merci pour vos conseils, je vais voir au plus vite pour me prendre un disque dur externe en espérant que mon pc tienne le coup jusque là :-)
Et merci aussi pour le lien concernant le fait de poster correctement un retour de commande car je n'avais pas trouvé
Je vous tiens au courant si j'ai du nouveau
à bientôt
Hors ligne
#10 Le 12/11/2019, à 21:11
- Nuliel
Re : initramfs au démarrage
Tu peux en profiter pour mettre un ssd à la place du disque dur dans le pc. Ça permettra d'accélérer le pc.
Ok pour le disque externe pour sauvegarder les données
Merci moko!
Hors ligne