#1 Le 07/03/2017, à 20:00
- pem1664
Raid 5 et mdadm [RESOLU]
Bonjour à tous!
J'ai un GROS souci avec mon serveur : j'ai un serveur avec 8dd de 2To monté en raid 5 avec mdadm, jusqu'ici tout allait bien sauf qu'après trop derreurs smart sur un des disques j'ai du le changer car le raid fonctionnait en mode dégradé.
Au reboot impossible de démarrer, sans passer par le mode de récupération virer du fstab la ligne de montage du raid et la le serveur veut bien booter. Et la grande grosse et mauvaise surprise mon raid 5 est vu comme un raid 0 inactif...
Et la j'ai essayé pas mal de choses non destructives mais rien a faire...
pem@Serveur1:~$ cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10]
md0 : inactive sdi[5](S) sdh[4](S) sdf[7](S) sde[6](S) sdd[3](S) sdc[2](S) sda[0](S) sdb[1](S)
15627068096 blocks super 1.2
unused devices: <none>pem@Serveur1:~$ sudo mdadm -Es
ARRAY /dev/md/0 metadata=1.2 UUID=28d825f1:156a6ed1:8e94696c:b5762cb5 name=Serveur1:0
pem@Serveur1:~$ pem@Serveur1:~$ sudo mdadm --assemble --scan --verbose
mdadm: looking for devices for /dev/md0
mdadm: /dev/sdi is busy - skipping
mdadm: /dev/sdh is busy - skipping
mdadm: no recogniseable superblock on /dev/sdg3
mdadm: no recogniseable superblock on /dev/sdg2
mdadm: no recogniseable superblock on /dev/sdg1
mdadm: Cannot assemble mbr metadata on /dev/sdg
mdadm: /dev/sdf is busy - skipping
mdadm: /dev/sde is busy - skipping
mdadm: /dev/sdd is busy - skipping
mdadm: /dev/sdc is busy - skipping
mdadm: /dev/sdb is busy - skipping
mdadm: /dev/sda is busy - skipping
mdadm: no recogniseable superblock on /dev/ram15
mdadm: no recogniseable superblock on /dev/ram14
mdadm: no recogniseable superblock on /dev/ram13
mdadm: no recogniseable superblock on /dev/ram12
mdadm: no recogniseable superblock on /dev/ram11
mdadm: no recogniseable superblock on /dev/ram10
mdadm: no recogniseable superblock on /dev/ram9
mdadm: no recogniseable superblock on /dev/ram8
mdadm: no recogniseable superblock on /dev/ram7
mdadm: no recogniseable superblock on /dev/ram6
mdadm: no recogniseable superblock on /dev/ram5
mdadm: no recogniseable superblock on /dev/ram4
mdadm: no recogniseable superblock on /dev/ram3
mdadm: no recogniseable superblock on /dev/ram2
mdadm: no recogniseable superblock on /dev/ram1
mdadm: no recogniseable superblock on /dev/ram0
pem@Serveur1:~$ je ne comprend pas trop... voici la ligne dans mdadm.conf :
ARRAY /dev/md0 level=raid5 num-devices=8 UUID=28d825f1:156a6ed1:8e94696c:b5762cb5j'ose pas passer par webmin et supprimer l'array de peur de tout perdre...
help me please 
EDIT : j'ai tout une tripoté de trucs dans le syslog :
Mar 7 20:06:01 Serveur1 CRON[3727]: (pem) CMD (bash /media/Serveur1/Scripts/script_temp/temp.sh)
Mar 7 20:06:01 Serveur1 CRON[3726]: (CRON) info (No MTA installed, discarding output)
Mar 7 20:06:40 Serveur1 /usr/lib/gdm3/gdm-x-session[12864]: Activating service name='org.gtk.vfs.Metadata'
Mar 7 20:06:40 Serveur1 /usr/lib/gdm3/gdm-x-session[12864]: Successfully activated service 'org.gtk.vfs.Metadata'
Mar 7 20:07:01 Serveur1 CRON[4133]: (pem) CMD (bash /media/Serveur1/Scripts/script_temp/temp.sh)
Mar 7 20:07:01 Serveur1 CRON[4132]: (CRON) info (No MTA installed, discarding output)
Mar 7 20:07:37 Serveur1 systemd[12854]: dev-disk-by\x2dpath-pci\x2d0000:00:14.1\x2data\x2d2.device: Dev dev-disk-by\x2dpath-pci\x2d0000:00:14.1\x2data\x2d2.device appeared twice with different sysfs paths /sys/devices/pci0000:00/0000:00:14.1/ata9/host8/target8:0:0/8:0:0:0/block/sdh and /sys/devices/pci0000:00/0000:00:14.1/ata9/host8/target8:0:1/8:0:1:0/block/sdi
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 systemd[1681]: dev-disk-by\x2dpath-pci\x2d0000:00:14.1\x2data\x2d2.device: Dev dev-disk-by\x2dpath-pci\x2d0000:00:14.1\x2data\x2d2.device appeared twice with different sysfs paths /sys/devices/pci0000:00/0000:00:14.1/ata9/host8/target8:0:1/8:0:1:0/block/sdi and /sys/devices/pci0000:00/0000:00:14.1/ata9/host8/target8:0:0/8:0:0:0/block/sdh
Mar 7 20:07:37 Serveur1 systemd[1]: dev-disk-by\x2dpath-pci\x2d0000:00:14.1\x2data\x2d2.device: Dev dev-disk-by\x2dpath-pci\x2d0000:00:14.1\x2data\x2d2.device appeared twice with different sysfs paths /sys/devices/pci0000:00/0000:00:14.1/ata9/host8/target8:0:1/8:0:1:0/block/sdi and /sys/devices/pci0000:00/0000:00:14.1/ata9/host8/target8:0:0/8:0:0:0/block/sdh
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:37 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:40 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/degraded': Failed to open file '/sys/devices/virtual/block/md0/md/degraded': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:40 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_action': Failed to open file '/sys/devices/virtual/block/md0/md/sync_action': No such file or directory (g-file-error-quark, 4)
Mar 7 20:07:40 Serveur1 udisksd[13119]: Error reading sysfs attr `/sys/devices/virtual/block/md0/md/sync_completed': Failed to open file '/sys/devices/virtual/block/md0/md/sync_completed': No such file or directory (g-file-error-quark, 4)EDIT 2
un fdisk -l donne :
pem@Serveur1:~$ sudo fdisk -l
[sudo] Mot de passe de pem :
Disque /dev/ram0 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram1 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram2 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram3 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram4 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram5 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram6 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram7 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram8 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram9 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram10 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram11 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram12 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram13 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram14 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disque /dev/ram15 : 64 MiB, 67108864 octets, 131072 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sda : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: 5E6602C3-A771-4BFA-9070-6E46D0203E20
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdb : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: F1903386-589F-49AF-BB27-17FC9404BB06
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdc : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: 02C109E6-27F6-4727-827B-77DD50BDDEF0
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdd : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 2C02ABB2-F85A-4C66-8979-6D0D1A3F8FB4
Disque /dev/sde : 149,1 GiB, 160041885696 octets, 312581808 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x5db9ea32
Périphérique Amorçage Start Fin Secteurs Size Id Type
/dev/sde1 * 2048 117186559 117184512 55,9G 83 Linux
/dev/sde2 117186560 132810751 15624192 7,5G 82 partition d'échange Linux / Solaris
/dev/sde3 132810752 312580095 179769344 85,7G 83 Linux
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdf : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 5A981F35-F79B-44B1-A595-9F7C0F0F849A
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdg : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 3D718AC7-7F7D-4E9B-9244-2E3CB215C55C
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdh : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: 0C961E5C-7FCC-4643-9B54-795C242F3D1D
The primary GPT table is corrupt, but the backup appears OK, so that will be used.
Disque /dev/sdi : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : sectors of 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 107FB411-3894-4FDC-A0F6-FE764C542C20
pem@Serveur1:~$ et après avoir désinstallé mdadm et réinstallé celui ci quand j'essaie d'assembler ca donne ca :
pem@Serveur1:~$ sudo mdadm --assemble --verbose --scan
mdadm: looking for devices for /dev/md/0
mdadm: no RAID superblock on /dev/sde3
mdadm: no RAID superblock on /dev/sde2
mdadm: no RAID superblock on /dev/sde1
mdadm: no RAID superblock on /dev/sde
mdadm: no RAID superblock on /dev/ram15
mdadm: no RAID superblock on /dev/ram14
mdadm: no RAID superblock on /dev/ram13
mdadm: no RAID superblock on /dev/ram12
mdadm: no RAID superblock on /dev/ram11
mdadm: no RAID superblock on /dev/ram10
mdadm: no RAID superblock on /dev/ram9
mdadm: no RAID superblock on /dev/ram8
mdadm: no RAID superblock on /dev/ram7
mdadm: no RAID superblock on /dev/ram6
mdadm: no RAID superblock on /dev/ram5
mdadm: no RAID superblock on /dev/ram4
mdadm: no RAID superblock on /dev/ram3
mdadm: no RAID superblock on /dev/ram2
mdadm: no RAID superblock on /dev/ram1
mdadm: no RAID superblock on /dev/ram0
mdadm: /dev/sdi is identified as a member of /dev/md/0, slot 7.
mdadm: /dev/sdh is identified as a member of /dev/md/0, slot 6.
mdadm: /dev/sdg is identified as a member of /dev/md/0, slot 5.
mdadm: /dev/sdf is identified as a member of /dev/md/0, slot 4.
mdadm: /dev/sdd is identified as a member of /dev/md/0, slot 3.
mdadm: /dev/sdc is identified as a member of /dev/md/0, slot 2.
mdadm: /dev/sdb is identified as a member of /dev/md/0, slot 1.
mdadm: /dev/sda is identified as a member of /dev/md/0, slot 0.
mdadm: added /dev/sdb to /dev/md/0 as 1
mdadm: added /dev/sdc to /dev/md/0 as 2
mdadm: added /dev/sdd to /dev/md/0 as 3 (possibly out of date)
mdadm: added /dev/sdf to /dev/md/0 as 4 (possibly out of date)
mdadm: added /dev/sdg to /dev/md/0 as 5
mdadm: added /dev/sdh to /dev/md/0 as 6
mdadm: added /dev/sdi to /dev/md/0 as 7
mdadm: added /dev/sda to /dev/md/0 as 0
mdadm: /dev/md/0 assembled from 6 drives - not enough to start the array.
pem@Serveur1:~$ Pourtant d'après le statut SMART /dev/sdf fonctionne correctement...
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-64-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WCAZA0926265
LU WWN Device Id: 5 0014ee 25a4c8c8b
Firmware Version: 51.0AB51
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 7 21:28:08 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37980) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 366) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 126 126 051 Pre-fail Always - 121992
3 Spin_Up_Time 0x0027 171 160 021 Pre-fail Always - 6408
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 250
5 Reallocated_Sector_Ct 0x0033 153 153 140 Pre-fail Always - 1025
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 16889
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 247
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 177
193 Load_Cycle_Count 0x0032 070 070 000 Old_age Always - 392602
194 Temperature_Celsius 0x0022 105 081 000 Old_age Always - 45
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 621
197 Current_Pending_Sector 0x0032 200 197 000 Old_age Always - 178
198 Offline_Uncorrectable 0x0030 200 199 000 Old_age Offline - 183
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 016 001 000 Old_age Offline - 49158
SMART Error Log Version: 1
ATA Error Count: 96 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 96 occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 45 00 00 00 a0 00 3d+03:06:47.900 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 3d+03:06:47.851 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 3d+03:06:42.548 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 3d+03:06:42.541 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 3d+03:06:42.533 IDENTIFY DEVICE
Error 95 occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 45 00 00 00 a0 00 3d+03:06:42.541 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 3d+03:06:42.533 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 3d+03:06:42.143 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 3d+03:06:42.136 SET FEATURES [Set transfer mode]
Error 94 occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 45 00 00 00 a0 00 3d+03:06:42.136 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 3d+03:06:42.127 IDENTIFY DEVICE
ca 00 01 08 00 00 e0 00 3d+03:06:39.333 WRITE DMA
ca 00 08 10 00 00 e0 00 3d+03:06:39.311 WRITE DMA
Error 93 occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 08 00 00 e0 Error: ABRT at LBA = 0x00000008 = 8
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 01 08 00 00 e0 00 3d+03:06:39.333 WRITE DMA
ca 00 08 10 00 00 e0 00 3d+03:06:39.311 WRITE DMA
ec 00 00 00 00 00 a0 00 3d+03:06:39.284 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 3d+03:06:39.284 SET FEATURES [Set transfer mode]
Error 92 occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 88 29 55 e0 Error: UNC 8 sectors at LBA = 0x00552988 = 5581192
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 88 29 55 e0 00 3d+03:06:36.523 READ DMA
ec 00 00 00 00 00 a0 00 3d+03:06:36.493 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 3d+03:06:36.493 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 14032 52940040
# 2 Short offline Completed without error 00% 8302 -
# 3 Short offline Completed: read failure 90% 8227 277947262
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.[résoluy]
Dernière modification par pem1664 (Le 26/03/2017, à 08:50)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#2 Le 07/03/2017, à 22:12
- Bougron
Re : Raid 5 et mdadm [RESOLU]
Bonsoir.
Tu indiques que tu as remplacé un disque qui lachait par un nouveau.
As-tu eu le temps de resynchroniser le nouveau disque aux 7 autres.
Si tu ne l'a pas fait, indiques son nom car il ne faut pas l'inclure dans la commande d'assemblage qui ne marche pas car tu as deux disques indiqués "out of date".
Je ne partage pas ton optimisme sur la qualité de SDF (178 secteurs impossibles à lire)
Merci de donner le retour de la commande
mdadm --examine /dev/sd[abcdef]afin d'evaluer le décalage des dates et voir si forcer l'assemblage risque de tout faire perdre car je suppose que tu n'as pas un double de ce raids5?
Dernière modification par Bougron (Le 07/03/2017, à 22:29)
Hors ligne
#3 Le 08/03/2017, à 00:11
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Bonsoir merci pour ton aide, ca devait etre sdc que j'ai changé, je pense en décembre et la resynchro s'était bien passé depuis je n'avais pas redémaré le serveur et ca fonctionnait correctement, j'avais eu des warning smart via webmin sur sdd et sdf mais jusqu’à présent ils fonctionnaient.. je comptait les changer car sdd donnait de plus en plus d'erreur smart... maintenant s'ils ont lachés en meme temps au dernier reboot c'est vraiment pas cool... :'(
voici le résultat de la commande légerement modifié pour avoir tous les disques normalement utilisés :
pem@Serveur1:~$ sudo mdadm --examine /dev/sd[abcdfghi]
/dev/sda:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : d16cc947:fd09a995:2e903fab:f2fb8b45
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:17 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 85ee4bc8 - correct
Events : 573767
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 0
Array State : AAA..AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdb:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : d3bbc737:dc379f5e:34d67d03:2ace388f
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:17 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : e0cde0ef - correct
Events : 573767
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 1
Array State : AAA..AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdc:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 9baf509e:d7fa2235:835b85de:92c2e599
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:17 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 38f1164 - correct
Events : 573767
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 2
Array State : AAA..AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdd:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : active
Device UUID : 2900765e:fd41d45b:e1c95ca2:cfd3489f
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Nov 30 18:24:43 2016
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : b337a5f4 - correct
Events : 9
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 3
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdf:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 0fc6ae36:f4c1703b:af771451:84688e09
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:01 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : 8471b88b - correct
Events : 573761
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 4
Array State : AAA.AAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdg:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : f79b9e44:62ab7da9:90751c22:0fb87eed
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:17 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : b567bdd7 - correct
Events : 573767
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 5
Array State : AAA..AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdh:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 9396e427:56cb25e9:ac8e5301:cd13b662
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:17 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 2cc44d42 - correct
Events : 573767
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 6
Array State : AAA..AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdi:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 3caf7005:e986794f:618ba285:d439ffeb
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:17 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 7e3c443b - correct
Events : 573767
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 7
Array State : AAA..AAA ('A' == active, '.' == missing, 'R' == replacing)
pem@Serveur1:~$ EDIT
Par contre y'a un truc étrange, je ne peut rien faire avec mdadm sans l'avoir préalablement désinstallé, rebooté le serveur et réinstallé... sinon mdadm skipp les disques qui sont sensés faire partie du raid...
EDIT 2
ben non evidemment... j'ai tout prévu pour faire une 2eme sauvegarde sur un 2eme serveur avec meme un carte réseau dédiée mais je voulais faire ca après avoir rangé tout mon bordel et je l'ai pas encore faite cette sauvegarde... ca aurait été trop beau... et puis pour le coup je me serai pas pris la tête... mais bon...
Dernière modification par pem1664 (Le 08/03/2017, à 00:47)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#4 Le 08/03/2017, à 00:54
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Ah! ca avance
Après suppression de mdadm, et reboot puis réinstallation j'ai pu relancer mon raid en forçant :
pem@Serveur1:~$ sudo mdadm --assemble /dev/md0 /dev/sd[abcdfghi] --force --verbose
mdadm: looking for devices for /dev/md0
mdadm: /dev/sda is identified as a member of /dev/md0, slot 0.
mdadm: /dev/sdb is identified as a member of /dev/md0, slot 1.
mdadm: /dev/sdc is identified as a member of /dev/md0, slot 2.
mdadm: /dev/sdd is identified as a member of /dev/md0, slot 3.
mdadm: /dev/sdf is identified as a member of /dev/md0, slot 4.
mdadm: /dev/sdg is identified as a member of /dev/md0, slot 5.
mdadm: /dev/sdh is identified as a member of /dev/md0, slot 6.
mdadm: /dev/sdi is identified as a member of /dev/md0, slot 7.
mdadm: forcing event count in /dev/sdd(3) from 9 upto 573767
mdadm: clearing FAULTY flag for device 3 in /dev/md0 for /dev/sdd
mdadm: Marking array /dev/md0 as 'clean'
mdadm: added /dev/sdb to /dev/md0 as 1
mdadm: added /dev/sdc to /dev/md0 as 2
mdadm: added /dev/sdd to /dev/md0 as 3
mdadm: added /dev/sdf to /dev/md0 as 4 (possibly out of date)
mdadm: added /dev/sdg to /dev/md0 as 5
mdadm: added /dev/sdh to /dev/md0 as 6
mdadm: added /dev/sdi to /dev/md0 as 7
mdadm: added /dev/sda to /dev/md0 as 0
mdadm: /dev/md0 has been started with 7 drives (out of 8).je viens de lancer un fsck et c'est blindé d'erreurs... 
j'espère que j'ai pas fait de bêtises...
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#5 Le 08/03/2017, à 01:56
- Bougron
Re : Raid 5 et mdadm [RESOLU]
Bonsoir.
Que tu vas vite.
Tu as six disques en bon état et bien synchronisés à Update Time : Tue Feb 28 21:30:17 2017 et au numero Events : 573767
Tu as le disque SDF qui a 16 secondes de retard à Update Time : Tue Feb 28 21:30:01 2017 et 6 N° de retard Events : 573761
Ton disque SDD est complètement HS Update Time : Wed Nov 30 18:24:43 2016 Events : 9
Merci de faire un smartctl de SDD pour voir s'il a un problème physique inaperçu
Je te conseille de ne pas l'utiliser si tu relances en forçant. Tu auras seulement 7 disques sur 8 car je pense que le tout petit décalage de SDF n'aura pas de grandes conséquences.
Je ne connais pas trop la commande. Certainement (en omettant la lettre D)
sudo mdadm --assemble --force --verbose /dev/md0 /dev/sd[abcfghi]Ajout je viens de voir dans ta trace que le disque SDD avait bien été éjecté et marqué HS.
mdadm: forcing event count in /dev/sdd(3) from 9 up to 573767
mdadm: clearing FAULTY flag for device 3 in /dev/md0 for /dev/sdd
Je ne sais absolument pas ce que ta réparation va donner pour l'accès à tes fichiers.
Je vois aussi
"mdadm: /dev/md0 has been started with 7 drives (out of 8)."
Je serais curieux de savoir lequel a été éjecté. Merci de refaire la commande d'état du raids que je t'ai proposée
Peut-être est-il en train de le reconstruire!
Si tu n'as pas fais un fsck avec demande de corrections, tu devrais pouvoir relancer avec 7 disques et voir ce que le fsck (non correctif) va signaler
Dernière modification par Bougron (Le 08/03/2017, à 02:30)
Hors ligne
#6 Le 08/03/2017, à 11:35
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Salut Bougron
Alors chose super étrange c'est sdf qui n'a pas été accepté par le raid... quand j'ai voulu monter le raid (avant de lancer fsck) j'ai eu ce message :
pem@Serveur1:~$ sudo mount /dev/md0 /media/Serveur1
mount: mount /dev/md0 on /media/Serveur1 failed: La structure a besoin d'un nettoyagedonc j'en ai conclu qu'il fallait faire un fsck correctif, que j'ai lancé et la pour le coup il n'est pas encore fini et il y a un bon paquet d'inode ou de noeuds à corriger..
voici le résultat du smartctl sur sdd :
pem@Serveur1:~$ sudo smartctl -x /dev/sdd
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-64-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WMAZA2383303
LU WWN Device Id: 5 0014ee 655f4325f
Firmware Version: 51.0AB51
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Mar 8 11:21:47 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (36000) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 347) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 194 194 051 - 11292
3 Spin_Up_Time POS--K 253 253 021 - 925
4 Start_Stop_Count -O--CK 100 100 000 - 274
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 2
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 079 079 000 - 15645
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 272
192 Power-Off_Retract_Count -O--CK 200 200 000 - 201
193 Load_Cycle_Count -O--CK 101 101 000 - 297692
194 Temperature_Celsius -O---K 100 078 000 - 50
196 Reallocated_Event_Count -O--CK 198 198 000 - 2
197 Current_Pending_Sector -O--CK 200 199 000 - 263
198 Offline_Uncorrectable ----CK 200 200 000 - 141
199 UDMA_CRC_Error_Count -O--CK 200 191 000 - 57079
200 Multi_Zone_Error_Rate ---R-- 192 096 000 - 2336
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 7212 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7212 [11] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 8e 56 49 20 40 00 Error: UNC at LBA = 0x8e564920 = 2388019488
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 20 00 10 00 00 8e 56 4a 20 40 08 7d+05:00:46.146 READ FPDMA QUEUED
60 00 80 00 08 00 00 8e 56 49 a0 40 08 7d+05:00:46.146 READ FPDMA QUEUED
60 00 80 00 00 00 00 8e 56 49 20 40 08 7d+05:00:46.145 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 7d+05:00:46.143 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 7d+05:00:46.143 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 7211 [10] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 8e 56 49 20 40 00 Error: UNC at LBA = 0x8e564920 = 2388019488
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 02 40 00 98 00 00 8e 56 48 00 40 08 7d+05:00:41.494 READ FPDMA QUEUED
60 02 40 00 90 00 00 8e 4d 24 00 40 08 7d+05:00:40.501 READ FPDMA QUEUED
60 00 20 00 88 00 00 8e 44 c6 08 40 08 7d+05:00:40.485 READ FPDMA QUEUED
60 00 08 00 80 00 00 8e 44 c6 00 40 08 7d+05:00:40.482 READ FPDMA QUEUED
60 00 20 00 78 00 00 8e 44 c1 90 40 08 7d+05:00:40.479 READ FPDMA QUEUED
Error 7210 [9] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 8e 16 49 20 40 00 Error: UNC at LBA = 0x8e164920 = 2383825184
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 60 00 70 00 00 8e 16 4a 20 40 08 7d+05:00:30.129 READ FPDMA QUEUED
60 00 80 00 68 00 00 8e 16 49 a0 40 08 7d+05:00:30.129 READ FPDMA QUEUED
60 00 80 00 60 00 00 8e 16 49 20 40 08 7d+05:00:30.128 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 7d+05:00:30.127 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 7d+05:00:30.127 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 7209 [8] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 8e 16 49 20 40 00 Error: UNC at LBA = 0x8e164920 = 2383825184
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 02 80 00 00 00 00 8e 16 48 00 40 08 7d+05:00:25.471 READ FPDMA QUEUED
60 02 40 00 f0 00 00 8e 0d 24 00 40 08 7d+05:00:24.539 READ FPDMA QUEUED
60 00 08 00 e8 00 00 8d ff a9 d8 40 08 7d+05:00:22.676 READ FPDMA QUEUED
60 00 20 00 e0 00 00 8d f6 07 88 40 08 7d+05:00:22.667 READ FPDMA QUEUED
60 00 08 00 d8 00 00 8d f6 07 80 40 08 7d+05:00:22.666 READ FPDMA QUEUED
Error 7208 [7] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 8a d6 49 20 40 00 Error: UNC at LBA = 0x8ad64920 = 2329299232
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 20 00 e0 00 00 8a d6 4a 20 40 08 7d+04:59:37.921 READ FPDMA QUEUED
60 00 80 00 d8 00 00 8a d6 49 a0 40 08 7d+04:59:37.921 READ FPDMA QUEUED
60 00 80 00 d0 00 00 8a d6 49 20 40 08 7d+04:59:37.920 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 7d+04:59:37.917 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 7d+04:59:37.917 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 7207 [6] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 8a d6 49 20 40 00 Error: UNC at LBA = 0x8ad64920 = 2329299232
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 02 40 00 70 00 00 8a d6 48 00 40 08 7d+04:59:34.172 READ FPDMA QUEUED
60 02 40 00 68 00 00 8a cd 24 00 40 08 7d+04:59:32.387 READ FPDMA QUEUED
60 00 08 00 60 00 00 8a b7 f6 f8 40 08 7d+04:59:30.848 READ FPDMA QUEUED
60 02 40 00 58 00 00 8a b1 b8 00 40 08 7d+04:59:29.086 READ FPDMA QUEUED
60 02 40 00 50 00 00 8a 96 48 00 40 08 7d+04:59:27.667 READ FPDMA QUEUED
Error 7206 [5] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 7c 96 49 20 40 00 Error: UNC at LBA = 0x7c964920 = 2090223904
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 80 00 88 00 00 7c 96 49 a0 40 08 7d+04:55:55.565 READ FPDMA QUEUED
60 00 80 00 80 00 00 7c 96 49 20 40 08 7d+04:55:55.564 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 7d+04:55:55.563 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 7d+04:55:55.563 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 7d+04:55:55.558 IDENTIFY DEVICE
Error 7205 [4] occurred at disk power-on lifetime: 15638 hours (651 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 7c 96 49 20 40 00 Error: UNC at LBA = 0x7c964920 = 2090223904
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 02 40 00 20 00 00 7c 96 48 00 40 08 7d+04:55:51.817 READ FPDMA QUEUED
60 00 08 00 18 00 00 7c 8d 35 00 40 08 7d+04:55:51.796 READ FPDMA QUEUED
60 00 08 00 10 00 00 7c 8d 31 00 40 08 7d+04:55:51.795 READ FPDMA QUEUED
60 00 08 00 08 00 00 7c 8d 29 00 40 08 7d+04:55:51.793 READ FPDMA QUEUED
60 04 00 00 00 00 00 7c 8d 24 00 40 08 7d+04:55:50.199 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 15631 4990780
# 2 Conveyance offline Completed: read failure 90% 15631 4990776
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 50 Celsius
Power Cycle Min/Max Temperature: 44/61 Celsius
Lifetime Min/Max Temperature: 0/72 Celsius
Under/Over Temperature Limit Count: 0/153
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (250)
Index Estimated Time Temperature Celsius
251 2017-03-08 03:24 49 ******************************
... ..( 8 skipped). .. ******************************
260 2017-03-08 03:33 49 ******************************
261 2017-03-08 03:34 50 *******************************
... ..(260 skipped). .. *******************************
44 2017-03-08 07:55 50 *******************************
45 2017-03-08 07:56 47 ****************************
... ..(122 skipped). .. ****************************
168 2017-03-08 09:59 47 ****************************
169 2017-03-08 10:00 48 *****************************
... ..( 38 skipped). .. *****************************
208 2017-03-08 10:39 48 *****************************
209 2017-03-08 10:40 49 ******************************
... ..( 40 skipped). .. ******************************
250 2017-03-08 11:21 49 ******************************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 50 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 645623 Vendor specificet celui sur sdf :
pem@Serveur1:~$ sudo smartctl -x /dev/sdf
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-64-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WCAZA0926265
LU WWN Device Id: 5 0014ee 25a4c8c8b
Firmware Version: 51.0AB51
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Mar 8 11:25:35 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37980) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 366) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 126 126 051 - 121992
3 Spin_Up_Time POS--K 171 160 021 - 6408
4 Start_Stop_Count -O--CK 100 100 000 - 250
5 Reallocated_Sector_Ct PO--CK 153 153 140 - 1025
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 077 077 000 - 16903
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 247
192 Power-Off_Retract_Count -O--CK 200 200 000 - 177
193 Load_Cycle_Count -O--CK 070 070 000 - 392899
194 Temperature_Celsius -O---K 100 081 000 - 50
196 Reallocated_Event_Count -O--CK 001 001 000 - 621
197 Current_Pending_Sector -O--CK 200 197 000 - 178
198 Offline_Uncorrectable ----CK 200 199 000 - 183
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 016 001 000 - 49158
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 1555 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1555 [18] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:47.900 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:47.851 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:42.548 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:42.541 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:42.533 IDENTIFY DEVICE
Error 1554 [17] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:42.541 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:42.533 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:42.143 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:42.136 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:42.136 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 1553 [16] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:42.136 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:42.136 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:42.127 IDENTIFY DEVICE
ca 00 00 00 01 00 00 00 00 00 08 e0 00 3d+03:06:39.333 WRITE DMA
ca 00 00 00 08 00 00 00 00 00 10 e0 00 3d+03:06:39.311 WRITE DMA
Error 1552 [15] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 00 00 00 00 00 00 00 e0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:42.136 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:42.127 IDENTIFY DEVICE
ca 00 00 00 01 00 00 00 00 00 08 e0 00 3d+03:06:39.333 WRITE DMA
ca 00 00 00 08 00 00 00 00 00 10 e0 00 3d+03:06:39.311 WRITE DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:39.291 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 1551 [14] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 08 e0 00 Error: ABRT at LBA = 0x00000008 = 8
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ca 00 00 00 01 00 00 00 00 00 08 e0 00 3d+03:06:39.333 WRITE DMA
ca 00 00 00 08 00 00 00 00 00 10 e0 00 3d+03:06:39.311 WRITE DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:39.291 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:39.284 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:39.284 SET FEATURES [Set transfer mode]
Error 1550 [13] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 00 55 29 88 e0 00 Error: UNC 8 sectors at LBA = 0x00552988 = 5581192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 55 29 88 e0 00 3d+03:06:36.523 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:36.501 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 3d+03:06:36.493 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 3d+03:06:36.493 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 3d+03:06:36.493 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 1549 [12] occurred at disk power-on lifetime: 16722 hours (696 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 00 55 29 88 e0 00 Error: UNC 8 sectors at LBA = 0x00552988 = 5581192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 55 29 88 e0 00 3d+03:06:33.726 READ DMA
25 00 00 00 08 00 00 b3 b2 e1 00 e0 00 3d+03:06:33.585 READ DMA EXT
25 00 00 00 08 00 00 b3 b2 e1 08 e0 00 3d+03:06:33.581 READ DMA EXT
25 00 00 00 28 00 00 b3 b2 df d8 e0 00 3d+03:06:33.548 READ DMA EXT
25 00 00 00 08 00 00 b3 b2 df d0 e0 00 3d+03:06:33.468 READ DMA EXT
Error 1548 [11] occurred at disk power-on lifetime: 16721 hours (696 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 58 00 00 b5 fc 9d e8 e0 00 Error: UNC 88 sectors at LBA = 0xb5fc9de8 = 3053231592
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 58 00 00 b5 fc 9d e8 e0 00 3d+02:04:21.340 READ DMA EXT
25 00 00 00 18 00 00 74 72 71 78 e0 00 3d+02:04:21.339 READ DMA EXT
ca 00 00 00 01 00 00 00 00 00 08 e0 00 3d+02:04:21.289 WRITE DMA
ca 00 00 00 08 00 00 00 00 00 10 e0 00 3d+02:04:21.261 WRITE DMA
25 00 00 00 08 00 00 b5 fc a1 90 e0 00 3d+02:04:21.260 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 16889 -
# 2 Conveyance offline Completed: read failure 80% 16889 175234264
# 3 Short offline Completed: read failure 90% 14032 52940040
# 4 Short offline Completed without error 00% 8302 -
# 5 Short offline Completed: read failure 90% 8227 277947262
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 50 Celsius
Power Cycle Min/Max Temperature: 42/63 Celsius
Lifetime Min/Max Temperature: 42/69 Celsius
Under/Over Temperature Limit Count: 0/187
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (44)
Index Estimated Time Temperature Celsius
45 2017-03-08 03:28 51 ********************************
... ..( 13 skipped). .. ********************************
59 2017-03-08 03:42 51 ********************************
60 2017-03-08 03:43 50 *******************************
61 2017-03-08 03:44 50 *******************************
62 2017-03-08 03:45 50 *******************************
63 2017-03-08 03:46 51 ********************************
64 2017-03-08 03:47 50 *******************************
... ..( 28 skipped). .. *******************************
93 2017-03-08 04:16 50 *******************************
94 2017-03-08 04:17 51 ********************************
95 2017-03-08 04:18 50 *******************************
... ..( 2 skipped). .. *******************************
98 2017-03-08 04:21 50 *******************************
99 2017-03-08 04:22 51 ********************************
100 2017-03-08 04:23 51 ********************************
101 2017-03-08 04:24 51 ********************************
102 2017-03-08 04:25 50 *******************************
103 2017-03-08 04:26 50 *******************************
104 2017-03-08 04:27 51 ********************************
105 2017-03-08 04:28 50 *******************************
... ..( 2 skipped). .. *******************************
108 2017-03-08 04:31 50 *******************************
109 2017-03-08 04:32 51 ********************************
110 2017-03-08 04:33 50 *******************************
... ..( 21 skipped). .. *******************************
132 2017-03-08 04:55 50 *******************************
133 2017-03-08 04:56 49 ******************************
134 2017-03-08 04:57 49 ******************************
135 2017-03-08 04:58 50 *******************************
... ..( 2 skipped). .. *******************************
138 2017-03-08 05:01 50 *******************************
139 2017-03-08 05:02 49 ******************************
140 2017-03-08 05:03 49 ******************************
141 2017-03-08 05:04 50 *******************************
... ..( 12 skipped). .. *******************************
154 2017-03-08 05:17 50 *******************************
155 2017-03-08 05:18 49 ******************************
156 2017-03-08 05:19 50 *******************************
... ..( 3 skipped). .. *******************************
160 2017-03-08 05:23 50 *******************************
161 2017-03-08 05:24 49 ******************************
... ..( 2 skipped). .. ******************************
164 2017-03-08 05:27 49 ******************************
165 2017-03-08 05:28 50 *******************************
166 2017-03-08 05:29 50 *******************************
167 2017-03-08 05:30 49 ******************************
... ..( 2 skipped). .. ******************************
170 2017-03-08 05:33 49 ******************************
171 2017-03-08 05:34 50 *******************************
172 2017-03-08 05:35 49 ******************************
... ..( 2 skipped). .. ******************************
175 2017-03-08 05:38 49 ******************************
176 2017-03-08 05:39 50 *******************************
177 2017-03-08 05:40 49 ******************************
... ..( 59 skipped). .. ******************************
237 2017-03-08 06:40 49 ******************************
238 2017-03-08 06:41 50 *******************************
... ..( 28 skipped). .. *******************************
267 2017-03-08 07:10 50 *******************************
268 2017-03-08 07:11 51 ********************************
269 2017-03-08 07:12 50 *******************************
... ..( 2 skipped). .. *******************************
272 2017-03-08 07:15 50 *******************************
273 2017-03-08 07:16 51 ********************************
274 2017-03-08 07:17 51 ********************************
275 2017-03-08 07:18 50 *******************************
276 2017-03-08 07:19 50 *******************************
277 2017-03-08 07:20 50 *******************************
278 2017-03-08 07:21 51 ********************************
279 2017-03-08 07:22 50 *******************************
... ..( 2 skipped). .. *******************************
282 2017-03-08 07:25 50 *******************************
283 2017-03-08 07:26 51 ********************************
284 2017-03-08 07:27 51 ********************************
285 2017-03-08 07:28 50 *******************************
286 2017-03-08 07:29 50 *******************************
287 2017-03-08 07:30 51 ********************************
288 2017-03-08 07:31 50 *******************************
289 2017-03-08 07:32 51 ********************************
290 2017-03-08 07:33 50 *******************************
291 2017-03-08 07:34 51 ********************************
292 2017-03-08 07:35 50 *******************************
... ..( 10 skipped). .. *******************************
303 2017-03-08 07:46 50 *******************************
304 2017-03-08 07:47 51 ********************************
... ..( 9 skipped). .. ********************************
314 2017-03-08 07:57 51 ********************************
315 2017-03-08 07:58 50 *******************************
316 2017-03-08 07:59 50 *******************************
317 2017-03-08 08:00 47 ****************************
318 2017-03-08 08:01 47 ****************************
319 2017-03-08 08:02 48 *****************************
320 2017-03-08 08:03 47 ****************************
... ..( 4 skipped). .. ****************************
325 2017-03-08 08:08 47 ****************************
326 2017-03-08 08:09 48 *****************************
... ..( 13 skipped). .. *****************************
340 2017-03-08 08:23 48 *****************************
341 2017-03-08 08:24 47 ****************************
342 2017-03-08 08:25 48 *****************************
... ..( 7 skipped). .. *****************************
350 2017-03-08 08:33 48 *****************************
351 2017-03-08 08:34 47 ****************************
352 2017-03-08 08:35 48 *****************************
... ..( 14 skipped). .. *****************************
367 2017-03-08 08:50 48 *****************************
368 2017-03-08 08:51 47 ****************************
... ..( 2 skipped). .. ****************************
371 2017-03-08 08:54 47 ****************************
372 2017-03-08 08:55 48 *****************************
373 2017-03-08 08:56 48 *****************************
374 2017-03-08 08:57 47 ****************************
375 2017-03-08 08:58 47 ****************************
376 2017-03-08 08:59 47 ****************************
377 2017-03-08 09:00 48 *****************************
378 2017-03-08 09:01 48 *****************************
379 2017-03-08 09:02 47 ****************************
380 2017-03-08 09:03 47 ****************************
381 2017-03-08 09:04 47 ****************************
382 2017-03-08 09:05 48 *****************************
383 2017-03-08 09:06 47 ****************************
... ..( 2 skipped). .. ****************************
386 2017-03-08 09:09 47 ****************************
387 2017-03-08 09:10 48 *****************************
388 2017-03-08 09:11 47 ****************************
... ..( 2 skipped). .. ****************************
391 2017-03-08 09:14 47 ****************************
392 2017-03-08 09:15 48 *****************************
393 2017-03-08 09:16 48 *****************************
394 2017-03-08 09:17 47 ****************************
... ..( 2 skipped). .. ****************************
397 2017-03-08 09:20 47 ****************************
398 2017-03-08 09:21 48 *****************************
399 2017-03-08 09:22 47 ****************************
... ..( 2 skipped). .. ****************************
402 2017-03-08 09:25 47 ****************************
403 2017-03-08 09:26 48 *****************************
404 2017-03-08 09:27 47 ****************************
... ..( 2 skipped). .. ****************************
407 2017-03-08 09:30 47 ****************************
408 2017-03-08 09:31 48 *****************************
409 2017-03-08 09:32 48 *****************************
410 2017-03-08 09:33 48 *****************************
411 2017-03-08 09:34 47 ****************************
412 2017-03-08 09:35 47 ****************************
413 2017-03-08 09:36 48 *****************************
... ..( 23 skipped). .. *****************************
437 2017-03-08 10:00 48 *****************************
438 2017-03-08 10:01 49 ******************************
439 2017-03-08 10:02 49 ******************************
440 2017-03-08 10:03 48 *****************************
441 2017-03-08 10:04 48 *****************************
442 2017-03-08 10:05 48 *****************************
443 2017-03-08 10:06 49 ******************************
444 2017-03-08 10:07 49 ******************************
445 2017-03-08 10:08 48 *****************************
... ..( 2 skipped). .. *****************************
448 2017-03-08 10:11 48 *****************************
449 2017-03-08 10:12 49 ******************************
... ..( 48 skipped). .. ******************************
20 2017-03-08 11:01 49 ******************************
21 2017-03-08 11:02 50 *******************************
... ..( 9 skipped). .. *******************************
31 2017-03-08 11:12 50 *******************************
32 2017-03-08 11:13 51 ********************************
33 2017-03-08 11:14 51 ********************************
34 2017-03-08 11:15 50 *******************************
... ..( 6 skipped). .. *******************************
41 2017-03-08 11:22 50 *******************************
42 2017-03-08 11:23 51 ********************************
43 2017-03-08 11:24 51 ********************************
44 2017-03-08 11:25 51 ********************************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 31 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 645827 Vendor specificj'ai relancé un mdadm --examine et c'est bien sdf qui n'est pas pris en compte dans le raid, alors que c'est celui qui a le moins d'erreur smart ...
pem@Serveur1:~$ sudo mdadm --examine /dev/sd[abcdfghi]
/dev/sda:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : d16cc947:fd09a995:2e903fab:f2fb8b45
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 85fcf896 - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 0
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdb:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : d3bbc737:dc379f5e:34d67d03:2ace388f
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : e0dc8dbd - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 1
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdc:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 9baf509e:d7fa2235:835b85de:92c2e599
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 39dbe32 - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 2
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdd:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 2900765e:fd41d45b:e1c95ca2:cfd3489f
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : b3c1e679 - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 3
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdf:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 0fc6ae36:f4c1703b:af771451:84688e09
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Feb 28 21:30:01 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : 8471b88b - correct
Events : 573761
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 4
Array State : AAA.AAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdg:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : f79b9e44:62ab7da9:90751c22:0fb87eed
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : b5766aa5 - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 5
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdh:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 9396e427:56cb25e9:ac8e5301:cd13b662
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 2cd2fa10 - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 6
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdi:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 3caf7005:e986794f:618ba285:d439ffeb
Internal Bitmap : 8 sectors from superblock
Update Time : Wed Mar 8 05:22:01 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 7e4af109 - correct
Events : 574726
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 7
Array State : AAAA.AAA ('A' == active, '.' == missing, 'R' == replacing)
pem@Serveur1:~$ et
pem@Serveur1:~$ sudo cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4]
md0 : active raid5 sda[0] sdi[7] sdh[6] sdg[5] sdd[3] sdc[2] sdb[1]
13673683968 blocks super 1.2 level 5, 512k chunk, algorithm 2 [8/7] [UUUU_UUU]
bitmap: 15/15 pages [60KB], 65536KB chunk
unused devices: <none>la j'attend la fin du fsck et qui me sort des noms de fichiers que je connais du genre :
Le fichier /Telechargements/evolution-backup-20120605.tar.gz (i-noeud n°76614487, date de modification Tue Jun 5 21:55:35 2012)
a 1 bloc(s) réclamé(s) plusieurs fois, partagés avec 0 fichier(s) :
Cloner les blocs réclamés plusieurs fois ? oui
clone_file_block: erreur interne : ne peut trouver dup_blk pour 748209481
Le fichier /Telechargements/zenbook_24Go.iso (i-noeud n°76614543, date de modification Wed Jan 2 20:32:43 2013)
a 1 bloc(s) réclamé(s) plusieurs fois, partagés avec 0 fichier(s) :
Cloner les blocs réclamés plusieurs fois ? ouice ue j'aimerai arriver a faire aujourd'hui c'est remplacer déja le disque sdd qui semble etre le plus pourri, même si c'est celui ci qui a été monté, forcer a remonter le raid avec sdf, resynchroniser, puis quand la resynchro sera fini changer sdf et rebelotte...
Crois tu qu'il est possible histoire de préserver aux mieux les données de faire une copie bit a bit d'un des disques du raid pour le remplacer?
Merci pour ton aide et tes conseils
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#7 Le 08/03/2017, à 13:56
- Bougron
Re : Raid 5 et mdadm [RESOLU]
Bonjour
Peut-être pourrait-tu faire un smartctl de tes 8 disques pour savoir si c'est bien SDD qui reste le prioritaire dans les remplacements
Si oui, on pourra le cloner bits à bits avec ddrescue à l'exception des secteurs illisibles!. qui sont actuellement 263
197 Current_Pending_Sector -O--CK 200 199 000 - 263Dernière modification par Bougron (Le 08/03/2017, à 14:34)
Hors ligne
#8 Le 08/03/2017, à 14:51
- Bougron
Re : Raid 5 et mdadm [RESOLU]
Comme je te l'ai dis, je ne suis pas expert en raids mais dans cette séquence tu écris
ce que j'aimerai arriver a faire aujourd'hui c'est remplacer déja le disque sdd qui semble être le plus pourri, même si c'est celui ci qui a été monté,
=> Je crois que tu as fais la commande de montage avec les 8 disques. Que cela a monté 7 disques et que tu es en train de faire un fsck.
A=> Il faudrait voir ce que cela donne. Si cela te semble bon.
Je ne comprends pas la suite de ton action
forcer à remonter le raid avec sdf, resynchroniser, puis quand la resynchro sera finie changer sdf et rebelotte...
Pour moi, cela consisterait à déclarer SDF en erreur.
mdadm --manage --set-faulty /dev/md0 /dev/sdfpuis démonter le disque SDF et le remplacer par un neuf (SDF?) puis synchroniser.
sudo mdadm --manage /dev/md0 --add /dev/sdfet suivre l'état de synchronisation avec cette commande ?
sudo mdadm -D /dev/md0 | egrep -i 'state :|Resync Status |Rebuild'
B=> Il faudrait voir ce que cela donne. Si cela ne te semble pas bon: Je ne sais pas si ce que je vais écrire sera mieux comme solution.
- déclarer le disque SDD en faute comme il l'était initialement
mdadm --manage --set-faulty /dev/md0 /dev/sdd- et Monter le raids sans ce disque SDD comme je l'ai dit en essayant de trouver la bonne codif pour qu'il inclue le disque SDF
sudo mdadm -S /dev/md0sudo mdadm -A -v -U resync -f /dev/md0 /dev/sd[abcfghi]De toute façon, lances la commande
cat /proc/mdstat afin de savoir l'état actuel après toutes tes opérations.
Dernière modification par Bougron (Le 09/03/2017, à 18:37)
Hors ligne
#9 Le 09/03/2017, à 11:11
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Merci Bougron pour tes conseils, pour l'instant ca fait plus de 20h de fsck et c'est pas fini... faut dire qu'il y a de grosses img de disques qui semblent etre altérées... je vais le laisser tourner et voir ce que ca donne et donne des nouvelles après
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#10 Le 12/03/2017, à 13:10
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Bonjour, bon au final impossible de faire une resync avec un nouveau disque y'en a toujours un qui flanche pendant la resync et c'est super long.. Pour l'instant je suis en train de faire une copie bit a bit d'un des disques défaillant puis j’essaierai de remonter le raid avec le nouveau disque
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#11 Le 12/03/2017, à 13:15
- Bougron
Re : Raid 5 et mdadm [RESOLU]
Bougron a écrit :
Bonjour
Peut-être pourrait-tu faire un smartctl de tes 8 disques pour savoir si c'est bien SDD qui reste le prioritaire dans les remplacementsSi oui, on pourra le cloner bits à bits avec ddrescue à l'exception des secteurs illisibles!. qui sont actuellement 263
197 Current_Pending_Sector -O--CK 200 199 000 - 263
Bonjour
Ce n'est pour rien que je t'avais demandé de vérifier l'état des disques avant t'entreprendre les actions.
Dernière modification par Bougron (Le 12/03/2017, à 13:15)
Hors ligne
#12 Le 12/03/2017, à 13:20
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Bonjour, oui oui j'avais bien compris
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#13 Le 26/03/2017, à 08:49
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Bonjour a tous
Ca y est je m'en suis enfin sorti avec mon raid et récupéré une bonne partie des données... (lost+found contient 1.7To sur les 12To)!!
En pratique j'ai fait une copie bit a bit avec ddrescue du disque /dev/sdf qui avait l'état smart le moins pourrit, j'ai essayé de faire de même avec le disque sdd mais pour le coup après 4j de lancement de dd rescue et 10% d'effectué j'ai abandonné.
Ensuite j'ai remonté le raid avec le nouveau disque sdf fraichement recopié sans erreur et inséré un nouveau disque à la place de sdd.
J'ai du réinstaller mdadm au reboot car il me trouvait encore un raid0 à la place d'un raid5.
Après réinstall de mdadm, j'ai pu recrééer le raid5 et le monter en mode dégradé (sans le disque sdd) puis rajouter le disque sdd et le reconstruire (pour le coup vu qu'il n'y avait plus de disque défectueux c'est allé assez vite).
Et enfin j'ai pu lancer un fsck pour corriger toutes les erreurs d'inodes (et ca pour le coup ca a duré 15j.. et encore je l'ai arrêté plusieurs fois pour supprimer les images trop grosses comme des iso de 30GO ou plus)
Et la pour l'instant C'est nickel un beau raid avec la moitié des disques neufs.. j'ai plus qu'a en racheter pour changer les disques auu fur et a mesure qu'ils tomberont en rade...
Un grand merci a toi Bougron pour ton aide et tes conseils
Dernière modification par pem1664 (Le 26/03/2017, à 08:55)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#14 Le 26/03/2017, à 08:56
- Bougron
Re : Raid 5 et mdadm [RESOLU]
Bonjour.
Merci de ton retour. Tu n'y es pour rien mais je note une sacrée contradiction
RAIDS = haute disponibilité et fsck = 15 jours Donc probablement pas autorisé en lecture
Hors ligne
#15 Le 26/03/2017, à 11:10
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Ben d'après iostat le raid tourne a en gros 50 a 60Mo/s mais lorsque le fsck copie les blocs réclamés plusieurs fois ca tombe a 0 et ca y reste le pc qui gère ce raid est un vieux AMD Athlon(tm) II X2 250 Processor × 2 et il y a 6 disques direct sur la CM et 2 qui sont sur une carte pci ->sata le fsck prennait 100% des ressources d'un proc et 6% d'un autre ca doit pas aider...
pourquoi dis tu "pas autorisé en lecture"?
Dernière modification par pem1664 (Le 26/03/2017, à 11:11)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#16 Le 26/03/2017, à 11:16
- Bougron
Re : Raid 5 et mdadm [RESOLU]
C'était juste une question Pendant le fonctionnement du FSCK , il me semble qu'on ne peut pas écrire dans la partition et ni la lire...
Si tel n'est pas le cas, j'éliminerais ma remarque.
Hors ligne
#17 Le 26/03/2017, à 11:18
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Ah oui pendant le fsck la partition doit etre impérativement démontée 
mais c'est vrai que j'ai trouvé ca super long par rapport au temps qu'il a fallu pour reconstruire le raid...
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#18 Le 28/03/2017, à 10:55
- pem1664
Re : Raid 5 et mdadm [RESOLU]
En fait en lancant des copies j'ai encore un souci avec ce raid, décidément...
lors de la copie j'ai des erreurs d'entrée sortie et le dmesg me donne ca :
[ 271.651994] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
[ 437.046633] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344653976 (offset 8388608 size 7815168 starting block 235515648)
[ 437.046640] Buffer I/O error on device md0, logical block 235515648
[ 437.046644] Buffer I/O error on device md0, logical block 235515649
[ 437.046646] Buffer I/O error on device md0, logical block 235515650
[ 437.046648] Buffer I/O error on device md0, logical block 235515651
[ 437.046650] Buffer I/O error on device md0, logical block 235515652
[ 437.046652] Buffer I/O error on device md0, logical block 235515653
[ 437.046655] Buffer I/O error on device md0, logical block 235515654
[ 437.046656] Buffer I/O error on device md0, logical block 235515655
[ 437.046658] Buffer I/O error on device md0, logical block 235515656
[ 437.046660] Buffer I/O error on device md0, logical block 235515657
[ 437.046703] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344653976 (offset 8388608 size 7815168 starting block 235515392)
[ 491.912906] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344526235 (offset 2144755712 size 5246976 starting block 237301760)
[ 491.912912] buffer_io_error: 362 callbacks suppressed
[ 491.912915] Buffer I/O error on device md0, logical block 237301760
[ 491.912924] Buffer I/O error on device md0, logical block 237301761
[ 491.912926] Buffer I/O error on device md0, logical block 237301762
[ 491.912929] Buffer I/O error on device md0, logical block 237301763
[ 491.912931] Buffer I/O error on device md0, logical block 237301764
[ 491.912933] Buffer I/O error on device md0, logical block 237301765
[ 491.912935] Buffer I/O error on device md0, logical block 237301766
[ 491.912937] Buffer I/O error on device md0, logical block 237301767
[ 491.912939] Buffer I/O error on device md0, logical block 237301768
[ 491.912941] Buffer I/O error on device md0, logical block 237301769
[ 542.152128] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344526184 (offset 947912704 size 8388608 starting block 255248640)
[ 542.152140] buffer_io_error: 246 callbacks suppressed
[ 542.152147] Buffer I/O error on device md0, logical block 255248640
[ 542.152160] Buffer I/O error on device md0, logical block 255248641
[ 542.152165] Buffer I/O error on device md0, logical block 255248642
[ 542.152170] Buffer I/O error on device md0, logical block 255248643
[ 542.152175] Buffer I/O error on device md0, logical block 255248644
[ 542.152179] Buffer I/O error on device md0, logical block 255248645
[ 542.152184] Buffer I/O error on device md0, logical block 255248646
[ 542.152189] Buffer I/O error on device md0, logical block 255248647
[ 542.152193] Buffer I/O error on device md0, logical block 255248648
[ 542.152198] Buffer I/O error on device md0, logical block 255248649
[ 542.152399] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344526184 (offset 947912704 size 8388608 starting block 255248384)j'ai lancé un fsck mais la partition est propre...
pem@Serveur1:~$ cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10]
md0 : active raid5 sdg[5] sdf[8] sdb[1] sdi[7] sdh[6] sdc[2] sdd[3] sda[0]
13673683968 blocks super 1.2 level 5, 512k chunk, algorithm 2 [8/8] [UUUUUUUU]
bitmap: 4/15 pages [16KB], 65536KB chunk
unused devices: <none>
pem@Serveur1:~$ pem@Serveur1:~$ sudo mdadm --examine /dev/sd[abcdefghi]
/dev/sda:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : d16cc947:fd09a995:2e903fab:f2fb8b45
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 86172367 - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 0
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdb:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : d3bbc737:dc379f5e:34d67d03:2ace388f
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : e0f6b88e - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 1
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdc:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 9baf509e:d7fa2235:835b85de:92c2e599
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 3b7e903 - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 2
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdd:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 2900765e:fd41d45b:e1c95ca2:cfd3489f
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : b3dc114a - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 3
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sde:
MBR Magic : aa55
Partition[0] : 117184512 sectors at 2048 (type 83)
Partition[1] : 15624192 sectors at 117186560 (type 82)
Partition[2] : 179769344 sectors at 132810752 (type 83)
/dev/sdf:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x9
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 865a3ec3:27e0c236:d7781a28:046eca0f
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors - bad blocks present.
Checksum : e9bf4210 - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 4
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdg:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : f79b9e44:62ab7da9:90751c22:0fb87eed
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : b5909576 - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 5
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdh:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 9396e427:56cb25e9:ac8e5301:cd13b662
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 2ced24e1 - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 6
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
/dev/sdi:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x1
Array UUID : 28d825f1:156a6ed1:8e94696c:b5762cb5
Name : Serveur1:0 (local to host Serveur1)
Creation Time : Tue Nov 8 16:18:56 2016
Raid Level : raid5
Raid Devices : 8
Avail Dev Size : 3906767024 (1862.89 GiB 2000.26 GB)
Array Size : 13673683968 (13040.24 GiB 14001.85 GB)
Used Dev Size : 3906766848 (1862.89 GiB 2000.26 GB)
Data Offset : 262144 sectors
Super Offset : 8 sectors
Unused Space : before=262056 sectors, after=176 sectors
State : clean
Device UUID : 3caf7005:e986794f:618ba285:d439ffeb
Internal Bitmap : 8 sectors from superblock
Update Time : Tue Mar 28 11:57:15 2017
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 7e651bda - correct
Events : 607039
Layout : left-symmetric
Chunk Size : 512K
Device Role : Active device 7
Array State : AAAAAAAA ('A' == active, '.' == missing, 'R' == replacing)
pem@Serveur1:~$ je ne comprend pas...
Dernière modification par pem1664 (Le 28/03/2017, à 10:58)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#19 Le 28/03/2017, à 11:21
- Bougron
Re : Raid 5 et mdadm [RESOLU]
pem1664 a écrit :
En fait en lançant des copies j'ai encore un souci avec ce raid, décidément...
lors de la copie j'ai des erreurs d'entrée sortie et le dmesg me donne ca :[ 271.651994] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 437.046633] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344653976 (offset 8388608 size 7815168 starting block 235515648) [ 437.046640] Buffer I/O error on device md0, logical block 235515648 [ 437.046644] Buffer I/O error on device md0, logical block 235515649 [ 437.046646] Buffer I/O error on device md0, logical block 235515650 [ 437.046648] Buffer I/O error on device md0, logical block 235515651 [ 437.046650] Buffer I/O error on device md0, logical block 235515652 [ 437.046652] Buffer I/O error on device md0, logical block 235515653 [ 437.046655] Buffer I/O error on device md0, logical block 235515654 [ 437.046656] Buffer I/O error on device md0, logical block 235515655 [ 437.046658] Buffer I/O error on device md0, logical block 235515656 [ 437.046660] Buffer I/O error on device md0, logical block 235515657 [ 437.046703] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344653976 (offset 8388608 size 7815168 starting block 235515392) [ 491.912906] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344526235 (offset 2144755712 size 5246976 starting block 237301760) [ 491.912912] buffer_io_error: 362 callbacks suppressed [ 491.912915] Buffer I/O error on device md0, logical block 237301760 [ 491.912924] Buffer I/O error on device md0, logical block 237301761 [ 491.912926] Buffer I/O error on device md0, logical block 237301762 [ 491.912929] Buffer I/O error on device md0, logical block 237301763 [ 491.912931] Buffer I/O error on device md0, logical block 237301764 [ 491.912933] Buffer I/O error on device md0, logical block 237301765 [ 491.912935] Buffer I/O error on device md0, logical block 237301766 [ 491.912937] Buffer I/O error on device md0, logical block 237301767 [ 491.912939] Buffer I/O error on device md0, logical block 237301768 [ 491.912941] Buffer I/O error on device md0, logical block 237301769 [ 542.152128] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344526184 (offset 947912704 size 8388608 starting block 255248640) [ 542.152140] buffer_io_error: 246 callbacks suppressed [ 542.152147] Buffer I/O error on device md0, logical block 255248640 [ 542.152160] Buffer I/O error on device md0, logical block 255248641 [ 542.152165] Buffer I/O error on device md0, logical block 255248642 [ 542.152170] Buffer I/O error on device md0, logical block 255248643 [ 542.152175] Buffer I/O error on device md0, logical block 255248644 [ 542.152179] Buffer I/O error on device md0, logical block 255248645 [ 542.152184] Buffer I/O error on device md0, logical block 255248646 [ 542.152189] Buffer I/O error on device md0, logical block 255248647 [ 542.152193] Buffer I/O error on device md0, logical block 255248648 [ 542.152198] Buffer I/O error on device md0, logical block 255248649 [ 542.152399] EXT4-fs warning (device md0): ext4_end_bio:329: I/O error -5 writing to inode 344526184 (offset 947912704 size 8388608 starting block 255248384)Je ne comprend pas...
Bonjour
Je ne suis pas sur de l'explication que je vais te donner.
Tout d'abord, la copie du fichier se passe-t-elle bien malgré ce message d'erreur
Ma question est liée au fait que si un secteur sur un disque est inécrivable le RAIDS, doit faire en sorte d'utiliser d'utiliser des secteurs de secours.
Mais les commandes de contrôle fsck ne vérifient pas le contenu des fichiers, seulement le contenu des zones stockant les noms de fichiers
Il faudrait que tu refasses un smartctl de tous tes disques
Mais, il serait possible que cela soit un bug? https://bugs.launchpad.net/ubuntu/+sour … ug/1359706
https://lists.debian.org/debian-kernel/ … 00233.html
Dernière modification par Bougron (Le 28/03/2017, à 11:38)
Hors ligne
#20 Le 28/03/2017, à 11:24
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Hello merci encore pour tes lumières
Je ne pense pas que la copie se termine je suis obligé de cliquer sur ignorer mais ca ne me dit pas si il ignore l'erreur et continue ou bien si ca ignore la fin du fichier a copier..
EDIT smartctl de tous les disques...
pem@Serveur1:~$ sudo smartctl -x /dev/sda
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4M5ANA1YU
LU WWN Device Id: 5 0014ee 2b876c4d8
Firmware Version: 82.00A82
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Mar 28 12:25:59 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (25680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 260) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 175 173 021 - 4216
4 Start_Stop_Count -O--CK 100 100 000 - 28
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 096 096 000 - 3374
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 28
192 Power-Off_Retract_Count -O--CK 200 200 000 - 17
193 Load_Cycle_Count -O--CK 200 200 000 - 2593
194 Temperature_Celsius -O---K 105 088 000 - 42
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 32/47 Celsius
Lifetime Min/Max Temperature: 9/59 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (41)
Index Estimated Time Temperature Celsius
42 2017-03-28 04:28 37 ******************
... ..( 10 skipped). .. ******************
53 2017-03-28 04:39 37 ******************
54 2017-03-28 04:40 38 *******************
... ..( 7 skipped). .. *******************
62 2017-03-28 04:48 38 *******************
63 2017-03-28 04:49 39 ********************
... ..( 20 skipped). .. ********************
84 2017-03-28 05:10 39 ********************
85 2017-03-28 05:11 40 *********************
... ..( 25 skipped). .. *********************
111 2017-03-28 05:37 40 *********************
112 2017-03-28 05:38 41 **********************
... ..( 78 skipped). .. **********************
191 2017-03-28 06:57 41 **********************
192 2017-03-28 06:58 37 ******************
... ..( 7 skipped). .. ******************
200 2017-03-28 07:06 37 ******************
201 2017-03-28 07:07 38 *******************
... ..( 7 skipped). .. *******************
209 2017-03-28 07:15 38 *******************
210 2017-03-28 07:16 37 ******************
... ..(108 skipped). .. ******************
319 2017-03-28 09:05 37 ******************
320 2017-03-28 09:06 36 *****************
... ..( 39 skipped). .. *****************
360 2017-03-28 09:46 36 *****************
361 2017-03-28 09:47 35 ****************
362 2017-03-28 09:48 35 ****************
363 2017-03-28 09:49 36 *****************
... ..( 36 skipped). .. *****************
400 2017-03-28 10:26 36 *****************
401 2017-03-28 10:27 35 ****************
... ..( 27 skipped). .. ****************
429 2017-03-28 10:55 35 ****************
430 2017-03-28 10:56 36 *****************
... ..( 22 skipped). .. *****************
453 2017-03-28 11:19 36 *****************
454 2017-03-28 11:20 35 ****************
... ..( 27 skipped). .. ****************
4 2017-03-28 11:48 35 ****************
5 2017-03-28 11:49 36 *****************
... ..( 28 skipped). .. *****************
34 2017-03-28 12:18 36 *****************
35 2017-03-28 12:19 37 ******************
... ..( 5 skipped). .. ******************
41 2017-03-28 12:25 37 ******************
SCT Error Recovery Control:
Read: 70 (7,0 seconds)
Write: 70 (7,0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 28 --- Lifetime Power-On Resets
0x01 0x010 4 3374 --- Power-on Hours
0x01 0x018 6 4125550077 --- Logical Sectors Written
0x01 0x020 6 7269087 --- Number of Write Commands
0x01 0x028 6 6050068387 --- Logical Sectors Read
0x01 0x030 6 13151079 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 3293 --- Spindle Motor Power-on Hours
0x03 0x010 4 1886 --- Head Flying Hours
0x03 0x018 4 2611 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 41 --- Current Temperature
0x05 0x010 1 38 --- Average Short Term Temperature
0x05 0x018 1 41 --- Average Long Term Temperature
0x05 0x020 1 58 --- Highest Temperature
0x05 0x028 1 23 --- Lowest Temperature
0x05 0x030 1 55 --- Highest Average Short Term Temperature
0x05 0x038 1 32 --- Lowest Average Short Term Temperature
0x05 0x040 1 47 --- Highest Average Long Term Temperature
0x05 0x048 1 41 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 435 --- Number of Hardware Resets
0x06 0x010 4 1549 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 51 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 50 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1038026 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WCAZA2027998
LU WWN Device Id: 5 0014ee 2afd3589e
Firmware Version: 51.0AB51
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 28 12:26:03 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (38880) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 375) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 253 253 021 - 1058
4 Start_Stop_Count -O--CK 100 100 000 - 344
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 077 077 000 - 17286
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 343
192 Power-Off_Retract_Count -O--CK 200 200 000 - 266
193 Load_Cycle_Count -O--CK 071 071 000 - 389837
194 Temperature_Celsius -O---K 107 075 000 - 43
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 5
198 Offline_Uncorrectable ----CK 200 200 000 - 5
199 UDMA_CRC_Error_Count -O--CK 200 191 000 - 59526
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 5
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 6
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 [5] occurred at disk power-on lifetime: 14589 hours (607 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 b3 ba dc b0 40 00 Error: UNC at LBA = 0xb3badcb0 = 3015367856
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 28 00 28 00 00 b3 ba dc b0 40 08 27d+03:43:30.423 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 e0 08 27d+03:43:30.386 FLUSH CACHE EXT
61 00 01 00 18 00 00 00 00 00 08 40 08 27d+03:43:30.385 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 e0 08 27d+03:43:30.385 FLUSH CACHE EXT
ea 00 00 00 00 00 00 00 00 00 00 e0 08 27d+03:43:30.365 FLUSH CACHE EXT
Error 5 [4] occurred at disk power-on lifetime: 14589 hours (607 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 b3 ba dc b0 40 00 Error: UNC at LBA = 0xb3badcb0 = 3015367856
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 28 00 78 00 00 b3 ba dc d8 40 08 27d+03:43:27.346 READ FPDMA QUEUED
60 00 38 00 70 00 00 b3 ba dc a0 40 08 27d+03:43:27.346 READ FPDMA QUEUED
60 00 10 00 68 00 00 b3 ba dc 88 40 08 27d+03:43:27.346 READ FPDMA QUEUED
60 00 10 00 60 00 00 b3 ba dc 68 40 08 27d+03:43:27.346 READ FPDMA QUEUED
60 00 60 00 58 00 00 b3 ba dc 08 40 08 27d+03:43:27.346 READ FPDMA QUEUED
Error 4 [3] occurred at disk power-on lifetime: 14566 hours (606 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 b3 ba dc 98 40 00 Error: UNC at LBA = 0xb3badc98 = 3015367832
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 90 00 00 b3 ba dc 98 40 08 26d+04:25:44.355 READ FPDMA QUEUED
61 00 08 00 88 00 00 00 00 00 10 40 08 26d+04:25:44.355 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 e0 08 26d+04:25:44.355 FLUSH CACHE EXT
ea 00 00 00 00 00 00 00 00 00 00 e0 08 26d+04:25:44.280 FLUSH CACHE EXT
61 00 01 00 70 00 00 00 00 00 08 40 08 26d+04:25:44.280 WRITE FPDMA QUEUED
Error 3 [2] occurred at disk power-on lifetime: 14566 hours (606 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 b3 ba dc 98 40 00 Error: UNC at LBA = 0xb3badc98 = 3015367832
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 68 00 00 b3 ba dc 98 40 08 26d+04:25:41.282 READ FPDMA QUEUED
60 00 08 00 60 00 00 b3 ba dc a0 40 08 26d+04:25:41.282 READ FPDMA QUEUED
60 00 08 00 58 00 00 b3 ba dc 90 40 08 26d+04:25:41.282 READ FPDMA QUEUED
60 00 08 00 50 00 00 b3 ba dc 88 40 08 26d+04:25:41.282 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 26d+04:25:41.282 SET FEATURES [Enable SATA feature]
Error 2 [1] occurred at disk power-on lifetime: 14566 hours (606 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 b3 ba dc 78 40 00 Error: UNC at LBA = 0xb3badc78 = 3015367800
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 10 00 f0 00 00 b3 ba dc 78 40 08 26d+04:25:38.333 READ FPDMA QUEUED
60 00 08 00 e0 00 00 b3 ba dc 88 40 08 26d+04:25:38.333 READ FPDMA QUEUED
60 00 08 00 d8 00 00 b3 ba dc 90 40 08 26d+04:25:38.333 READ FPDMA QUEUED
60 00 08 00 d0 00 00 b3 ba dc a0 40 08 26d+04:25:38.333 READ FPDMA QUEUED
60 00 08 00 c8 00 00 b3 ba dc 98 40 08 26d+04:25:38.333 READ FPDMA QUEUED
Error 1 [0] occurred at disk power-on lifetime: 14566 hours (606 days + 22 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 fe 00 00 b3 ba dc 78 40 00 Error: UNC at LBA = 0xb3badc78 = 3015367800
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 b0 00 00 b3 ba dc 98 40 08 26d+04:25:35.392 READ FPDMA QUEUED
60 00 08 00 a8 00 00 b3 ba dc a0 40 08 26d+04:25:35.392 READ FPDMA QUEUED
60 00 08 00 a0 00 00 b3 ba dc 90 40 08 26d+04:25:35.391 READ FPDMA QUEUED
60 00 08 00 98 00 00 b3 ba dc 88 40 08 26d+04:25:35.391 READ FPDMA QUEUED
60 00 18 00 90 00 00 b3 ba dc 70 40 08 26d+04:25:35.391 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 43 Celsius
Power Cycle Min/Max Temperature: 28/50 Celsius
Lifetime Min/Max Temperature: 28/75 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (258)
Index Estimated Time Temperature Celsius
259 2017-03-28 04:29 32 *************
... ..( 8 skipped). .. *************
268 2017-03-28 04:38 32 *************
269 2017-03-28 04:39 31 ************
270 2017-03-28 04:40 31 ************
271 2017-03-28 04:41 32 *************
272 2017-03-28 04:42 32 *************
273 2017-03-28 04:43 31 ************
... ..( 2 skipped). .. ************
276 2017-03-28 04:46 31 ************
277 2017-03-28 04:47 32 *************
278 2017-03-28 04:48 31 ************
... ..( 8 skipped). .. ************
287 2017-03-28 04:57 31 ************
288 2017-03-28 04:58 30 ***********
289 2017-03-28 04:59 30 ***********
290 2017-03-28 05:00 30 ***********
291 2017-03-28 05:01 31 ************
... ..( 4 skipped). .. ************
296 2017-03-28 05:06 31 ************
297 2017-03-28 05:07 30 ***********
298 2017-03-28 05:08 31 ************
... ..( 31 skipped). .. ************
330 2017-03-28 05:40 31 ************
331 2017-03-28 05:41 32 *************
332 2017-03-28 05:42 31 ************
... ..( 7 skipped). .. ************
340 2017-03-28 05:50 31 ************
341 2017-03-28 05:51 32 *************
342 2017-03-28 05:52 31 ************
343 2017-03-28 05:53 31 ************
344 2017-03-28 05:54 32 *************
345 2017-03-28 05:55 32 *************
346 2017-03-28 05:56 31 ************
347 2017-03-28 05:57 31 ************
348 2017-03-28 05:58 31 ************
349 2017-03-28 05:59 32 *************
... ..( 20 skipped). .. *************
370 2017-03-28 06:20 32 *************
371 2017-03-28 06:21 33 **************
372 2017-03-28 06:22 32 *************
... ..( 2 skipped). .. *************
375 2017-03-28 06:25 32 *************
376 2017-03-28 06:26 33 **************
... ..( 4 skipped). .. **************
381 2017-03-28 06:31 33 **************
382 2017-03-28 06:32 34 ***************
383 2017-03-28 06:33 34 ***************
384 2017-03-28 06:34 34 ***************
385 2017-03-28 06:35 33 **************
386 2017-03-28 06:36 34 ***************
387 2017-03-28 06:37 33 **************
388 2017-03-28 06:38 33 **************
389 2017-03-28 06:39 33 **************
390 2017-03-28 06:40 34 ***************
391 2017-03-28 06:41 35 ****************
392 2017-03-28 06:42 34 ***************
393 2017-03-28 06:43 35 ****************
394 2017-03-28 06:44 35 ****************
395 2017-03-28 06:45 35 ****************
396 2017-03-28 06:46 36 *****************
... ..( 11 skipped). .. *****************
408 2017-03-28 06:58 36 *****************
409 2017-03-28 06:59 37 ******************
410 2017-03-28 07:00 36 *****************
411 2017-03-28 07:01 36 *****************
412 2017-03-28 07:02 37 ******************
413 2017-03-28 07:03 36 *****************
414 2017-03-28 07:04 37 ******************
... ..( 6 skipped). .. ******************
421 2017-03-28 07:11 37 ******************
422 2017-03-28 07:12 38 *******************
... ..( 6 skipped). .. *******************
429 2017-03-28 07:19 38 *******************
430 2017-03-28 07:20 39 ********************
... ..( 6 skipped). .. ********************
437 2017-03-28 07:27 39 ********************
438 2017-03-28 07:28 40 *********************
... ..( 5 skipped). .. *********************
444 2017-03-28 07:34 40 *********************
445 2017-03-28 07:35 41 **********************
446 2017-03-28 07:36 40 *********************
... ..( 11 skipped). .. *********************
458 2017-03-28 07:48 40 *********************
459 2017-03-28 07:49 41 **********************
... ..( 21 skipped). .. **********************
3 2017-03-28 08:11 41 **********************
4 2017-03-28 08:12 42 ***********************
5 2017-03-28 08:13 41 **********************
... ..( 25 skipped). .. **********************
31 2017-03-28 08:39 41 **********************
32 2017-03-28 08:40 42 ***********************
... ..( 17 skipped). .. ***********************
50 2017-03-28 08:58 42 ***********************
51 2017-03-28 08:59 43 ************************
52 2017-03-28 09:00 43 ************************
53 2017-03-28 09:01 40 *********************
... ..( 13 skipped). .. *********************
67 2017-03-28 09:15 40 *********************
68 2017-03-28 09:16 41 **********************
69 2017-03-28 09:17 40 *********************
... ..( 2 skipped). .. *********************
72 2017-03-28 09:20 40 *********************
73 2017-03-28 09:21 41 **********************
74 2017-03-28 09:22 40 *********************
... ..( 2 skipped). .. *********************
77 2017-03-28 09:25 40 *********************
78 2017-03-28 09:26 41 **********************
79 2017-03-28 09:27 40 *********************
80 2017-03-28 09:28 40 *********************
81 2017-03-28 09:29 40 *********************
82 2017-03-28 09:30 41 **********************
83 2017-03-28 09:31 40 *********************
... ..( 26 skipped). .. *********************
110 2017-03-28 09:58 40 *********************
111 2017-03-28 09:59 39 ********************
112 2017-03-28 10:00 39 ********************
113 2017-03-28 10:01 40 *********************
114 2017-03-28 10:02 40 *********************
115 2017-03-28 10:03 40 *********************
116 2017-03-28 10:04 39 ********************
117 2017-03-28 10:05 39 ********************
118 2017-03-28 10:06 39 ********************
119 2017-03-28 10:07 40 *********************
... ..( 3 skipped). .. *********************
123 2017-03-28 10:11 40 *********************
124 2017-03-28 10:12 39 ********************
125 2017-03-28 10:13 39 ********************
126 2017-03-28 10:14 38 *******************
... ..( 3 skipped). .. *******************
130 2017-03-28 10:18 38 *******************
131 2017-03-28 10:19 37 ******************
... ..( 2 skipped). .. ******************
134 2017-03-28 10:22 37 ******************
135 2017-03-28 10:23 36 *****************
... ..( 14 skipped). .. *****************
150 2017-03-28 10:38 36 *****************
151 2017-03-28 10:39 35 ****************
... ..( 5 skipped). .. ****************
157 2017-03-28 10:45 35 ****************
158 2017-03-28 10:46 34 ***************
159 2017-03-28 10:47 34 ***************
160 2017-03-28 10:48 35 ****************
161 2017-03-28 10:49 35 ****************
162 2017-03-28 10:50 35 ****************
163 2017-03-28 10:51 34 ***************
... ..( 9 skipped). .. ***************
173 2017-03-28 11:01 34 ***************
174 2017-03-28 11:02 33 **************
175 2017-03-28 11:03 34 ***************
176 2017-03-28 11:04 34 ***************
177 2017-03-28 11:05 34 ***************
178 2017-03-28 11:06 33 **************
... ..( 34 skipped). .. **************
213 2017-03-28 11:41 33 **************
214 2017-03-28 11:42 32 *************
... ..( 8 skipped). .. *************
223 2017-03-28 11:51 32 *************
224 2017-03-28 11:52 31 ************
225 2017-03-28 11:53 31 ************
226 2017-03-28 11:54 32 *************
227 2017-03-28 11:55 32 *************
228 2017-03-28 11:56 32 *************
229 2017-03-28 11:57 31 ************
230 2017-03-28 11:58 31 ************
231 2017-03-28 11:59 32 *************
... ..( 26 skipped). .. *************
258 2017-03-28 12:26 32 *************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 40 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 1038032 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sdc
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4M6JVEC2Z
LU WWN Device Id: 5 0014ee 20dcbc7a2
Firmware Version: 82.00A82
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Mar 28 12:26:06 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (25680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 260) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 172 172 021 - 4366
4 Start_Stop_Count -O--CK 100 100 000 - 15
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 096 096 000 - 3349
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 15
192 Power-Off_Retract_Count -O--CK 200 200 000 - 7
193 Load_Cycle_Count -O--CK 200 200 000 - 2493
194 Temperature_Celsius -O---K 111 092 000 - 36
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 36 Celsius
Power Cycle Min/Max Temperature: 24/41 Celsius
Lifetime Min/Max Temperature: 2/55 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (474)
Index Estimated Time Temperature Celsius
475 2017-03-28 04:29 29 **********
476 2017-03-28 04:30 29 **********
477 2017-03-28 04:31 29 **********
0 2017-03-28 04:32 30 ***********
... ..( 7 skipped). .. ***********
8 2017-03-28 04:40 30 ***********
9 2017-03-28 04:41 31 ************
... ..( 22 skipped). .. ************
32 2017-03-28 05:04 31 ************
33 2017-03-28 05:05 32 *************
... ..( 14 skipped). .. *************
48 2017-03-28 05:20 32 *************
49 2017-03-28 05:21 33 **************
... ..( 15 skipped). .. **************
65 2017-03-28 05:37 33 **************
66 2017-03-28 05:38 34 ***************
... ..( 14 skipped). .. ***************
81 2017-03-28 05:53 34 ***************
82 2017-03-28 05:54 35 ****************
... ..( 38 skipped). .. ****************
121 2017-03-28 06:33 35 ****************
122 2017-03-28 06:34 36 *****************
... ..( 23 skipped). .. *****************
146 2017-03-28 06:58 36 *****************
147 2017-03-28 06:59 30 ***********
148 2017-03-28 07:00 31 ************
... ..( 29 skipped). .. ************
178 2017-03-28 07:30 31 ************
179 2017-03-28 07:31 30 ***********
... ..( 28 skipped). .. ***********
208 2017-03-28 08:00 30 ***********
209 2017-03-28 08:01 31 ************
... ..( 3 skipped). .. ************
213 2017-03-28 08:05 31 ************
214 2017-03-28 08:06 30 ***********
... ..( 18 skipped). .. ***********
233 2017-03-28 08:25 30 ***********
234 2017-03-28 08:26 29 **********
... ..( 53 skipped). .. **********
288 2017-03-28 09:20 29 **********
289 2017-03-28 09:21 28 *********
... ..(177 skipped). .. *********
467 2017-03-28 12:19 28 *********
468 2017-03-28 12:20 29 **********
... ..( 5 skipped). .. **********
474 2017-03-28 12:26 29 **********
SCT Error Recovery Control:
Read: 70 (7,0 seconds)
Write: 70 (7,0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 15 --- Lifetime Power-On Resets
0x01 0x010 4 3349 --- Power-on Hours
0x01 0x018 6 4160473959 --- Logical Sectors Written
0x01 0x020 6 6909766 --- Number of Write Commands
0x01 0x028 6 5402683043 --- Logical Sectors Read
0x01 0x030 6 9054929 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 3267 --- Spindle Motor Power-on Hours
0x03 0x010 4 1846 --- Head Flying Hours
0x03 0x018 4 2501 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 35 --- Current Temperature
0x05 0x010 1 32 --- Average Short Term Temperature
0x05 0x018 1 36 --- Average Long Term Temperature
0x05 0x020 1 54 --- Highest Temperature
0x05 0x028 1 18 --- Lowest Temperature
0x05 0x030 1 52 --- Highest Average Short Term Temperature
0x05 0x038 1 22 --- Lowest Average Short Term Temperature
0x05 0x040 1 43 --- Highest Average Long Term Temperature
0x05 0x048 1 36 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 294 --- Number of Hardware Resets
0x06 0x010 4 1730 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 51 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 51 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1038019 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sdd
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4M6TF9EF5
LU WWN Device Id: 5 0014ee 263210163
Firmware Version: 82.00A82
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Mar 28 12:26:09 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (27240) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 275) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 100 253 021 - 0
4 Start_Stop_Count -O--CK 100 100 000 - 2
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 381
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 2
192 Power-Off_Retract_Count -O--CK 200 200 000 - 0
193 Load_Cycle_Count -O--CK 200 200 000 - 365
194 Temperature_Celsius -O---K 103 096 000 - 44
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 380 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 44 Celsius
Power Cycle Min/Max Temperature: 29/52 Celsius
Lifetime Min/Max Temperature: 14/52 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (385)
Index Estimated Time Temperature Celsius
386 2017-03-28 04:29 39 ********************
... ..( 31 skipped). .. ********************
418 2017-03-28 05:01 39 ********************
419 2017-03-28 05:02 38 *******************
... ..( 14 skipped). .. *******************
434 2017-03-28 05:17 38 *******************
435 2017-03-28 05:18 39 ********************
436 2017-03-28 05:19 38 *******************
... ..( 2 skipped). .. *******************
439 2017-03-28 05:22 38 *******************
440 2017-03-28 05:23 39 ********************
... ..( 18 skipped). .. ********************
459 2017-03-28 05:42 39 ********************
460 2017-03-28 05:43 38 *******************
... ..( 12 skipped). .. *******************
473 2017-03-28 05:56 38 *******************
474 2017-03-28 05:57 37 ******************
... ..( 44 skipped). .. ******************
41 2017-03-28 06:42 37 ******************
42 2017-03-28 06:43 36 *****************
... ..( 25 skipped). .. *****************
68 2017-03-28 07:09 36 *****************
69 2017-03-28 07:10 35 ****************
... ..( 12 skipped). .. ****************
82 2017-03-28 07:23 35 ****************
83 2017-03-28 07:24 36 *****************
... ..( 29 skipped). .. *****************
113 2017-03-28 07:54 36 *****************
114 2017-03-28 07:55 35 ****************
... ..( 15 skipped). .. ****************
130 2017-03-28 08:11 35 ****************
131 2017-03-28 08:12 34 ***************
... ..( 4 skipped). .. ***************
136 2017-03-28 08:17 34 ***************
137 2017-03-28 08:18 35 ****************
... ..( 48 skipped). .. ****************
186 2017-03-28 09:07 35 ****************
187 2017-03-28 09:08 34 ***************
... ..( 8 skipped). .. ***************
196 2017-03-28 09:17 34 ***************
197 2017-03-28 09:18 35 ****************
... ..( 9 skipped). .. ****************
207 2017-03-28 09:28 35 ****************
208 2017-03-28 09:29 36 *****************
... ..( 13 skipped). .. *****************
222 2017-03-28 09:43 36 *****************
223 2017-03-28 09:44 35 ****************
... ..( 4 skipped). .. ****************
228 2017-03-28 09:49 35 ****************
229 2017-03-28 09:50 36 *****************
... ..( 15 skipped). .. *****************
245 2017-03-28 10:06 36 *****************
246 2017-03-28 10:07 37 ******************
... ..( 3 skipped). .. ******************
250 2017-03-28 10:11 37 ******************
251 2017-03-28 10:12 38 *******************
... ..( 8 skipped). .. *******************
260 2017-03-28 10:21 38 *******************
261 2017-03-28 10:22 39 ********************
... ..( 13 skipped). .. ********************
275 2017-03-28 10:36 39 ********************
276 2017-03-28 10:37 40 *********************
... ..( 11 skipped). .. *********************
288 2017-03-28 10:49 40 *********************
289 2017-03-28 10:50 41 **********************
... ..( 29 skipped). .. **********************
319 2017-03-28 11:20 41 **********************
320 2017-03-28 11:21 42 ***********************
... ..( 38 skipped). .. ***********************
359 2017-03-28 12:00 42 ***********************
360 2017-03-28 12:01 43 ************************
... ..( 17 skipped). .. ************************
378 2017-03-28 12:19 43 ************************
379 2017-03-28 12:20 44 *************************
... ..( 5 skipped). .. *************************
385 2017-03-28 12:26 44 *************************
SCT Error Recovery Control:
Read: 70 (7,0 seconds)
Write: 70 (7,0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 2 --- Lifetime Power-On Resets
0x01 0x010 4 381 --- Power-on Hours
0x01 0x018 6 520398581 --- Logical Sectors Written
0x01 0x020 6 1061175 --- Number of Write Commands
0x01 0x028 6 3938889751 --- Logical Sectors Read
0x01 0x030 6 3936972 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 376 --- Spindle Motor Power-on Hours
0x03 0x010 4 212 --- Head Flying Hours
0x03 0x018 4 365 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 43 --- Current Temperature
0x05 0x010 1 39 --- Average Short Term Temperature
0x05 0x018 1 - --- Average Long Term Temperature
0x05 0x020 1 51 --- Highest Temperature
0x05 0x028 1 21 --- Lowest Temperature
0x05 0x030 1 41 --- Highest Average Short Term Temperature
0x05 0x038 1 33 --- Lowest Average Short Term Temperature
0x05 0x040 1 - --- Highest Average Long Term Temperature
0x05 0x048 1 - --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 54 --- Number of Hardware Resets
0x06 0x010 4 79 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 50 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 51 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1037997 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sde
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax 10 (ATA/133 and SATA/150)
Device Model: Maxtor 6L160P0
Serial Number: L30SHRCH
Firmware Version: BAJ41G10
User Capacity: 160 041 885 696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 0
Local Time is: Tue Mar 28 12:26:11 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is: 254 (maximum performance), recommended: 192
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 1202) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 61) minutes.
SCT capabilities: (0x0021) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
3 Spin_Up_Time POS--K 207 207 063 - 15626
4 Start_Stop_Count -O--CK 253 253 000 - 633
5 Reallocated_Sector_Ct PO--CK 253 253 063 - 0
6 Read_Channel_Margin P----- 253 253 100 - 0
7 Seek_Error_Rate -O-R-- 253 252 000 - 0
8 Seek_Time_Performance POS--K 245 233 187 - 43498
9 Power_On_Minutes -O--CK 132 132 000 - 585h+56m
10 Spin_Retry_Count PO-R-K 253 252 157 - 0
11 Calibration_Retry_Count PO-R-K 253 252 223 - 0
12 Power_Cycle_Count -O--CK 251 251 000 - 810
192 Power-Off_Retract_Count -O--CK 253 253 000 - 0
193 Load_Cycle_Count -O--CK 253 253 000 - 0
194 Temperature_Celsius -O--CK 043 253 000 - 44
195 Hardware_ECC_Recovered -O-R-- 253 252 000 - 13973
196 Reallocated_Event_Count ---R-- 253 253 000 - 0
197 Current_Pending_Sector ---R-- 253 253 000 - 0
198 Offline_Uncorrectable ---R-- 253 253 000 - 0
199 UDMA_CRC_Error_Count ---R-- 001 001 000 - 1825
200 Multi_Zone_Error_Rate -O-R-- 253 252 000 - 0
201 Soft_Read_Error_Rate -O-R-- 253 252 000 - 0
202 Data_Address_Mark_Errs -O-R-- 253 252 000 - 0
203 Run_Out_Cancel PO-R-- 253 252 180 - 0
204 Soft_ECC_Correction -O-R-- 253 252 000 - 0
205 Thermal_Asperity_Rate -O-R-- 253 252 000 - 0
207 Spin_High_Current -O-R-K 253 252 000 - 0
208 Spin_Buzz -O-R-K 253 252 000 - 0
209 Offline_Seek_Performnce --S--K 234 234 000 - 232
210 Unknown_Attribute -O--CK 253 252 000 - 0
211 Unknown_Attribute -O--CK 253 252 000 - 0
212 Unknown_Attribute -O--CK 253 252 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 1 Comprehensive SMART error log
0x03 GPL,SL R/O 4 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 SATA NCQ Queued Error log
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
SMART Extended Comprehensive Error Log Version: 1 (4 sectors)
No Errors Logged
SMART Extended Self-test Log (GP Log 0x07) not supported
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 1 (0x0001)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 44 Celsius
Power Cycle Max Temperature: 49 Celsius
Lifetime Max Temperature: 65 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: 0/71 Celsius
Temperature History Size (Index): 478 (477)
Index Estimated Time Temperature Celsius
0 2017-03-28 04:29 40 *********************
... ..( 65 skipped). .. *********************
66 2017-03-28 05:35 40 *********************
67 2017-03-28 05:36 39 ********************
68 2017-03-28 05:37 40 *********************
69 2017-03-28 05:38 39 ********************
70 2017-03-28 05:39 40 *********************
71 2017-03-28 05:40 39 ********************
... ..( 66 skipped). .. ********************
138 2017-03-28 06:47 39 ********************
139 2017-03-28 06:48 38 *******************
140 2017-03-28 06:49 39 ********************
... ..( 7 skipped). .. ********************
148 2017-03-28 06:57 39 ********************
149 2017-03-28 06:58 38 *******************
150 2017-03-28 06:59 39 ********************
151 2017-03-28 07:00 39 ********************
152 2017-03-28 07:01 38 *******************
153 2017-03-28 07:02 39 ********************
154 2017-03-28 07:03 38 *******************
... ..(131 skipped). .. *******************
286 2017-03-28 09:15 38 *******************
287 2017-03-28 09:16 39 ********************
288 2017-03-28 09:17 38 *******************
289 2017-03-28 09:18 39 ********************
290 2017-03-28 09:19 38 *******************
291 2017-03-28 09:20 39 ********************
292 2017-03-28 09:21 38 *******************
293 2017-03-28 09:22 39 ********************
... ..( 24 skipped). .. ********************
318 2017-03-28 09:47 39 ********************
319 2017-03-28 09:48 40 *********************
320 2017-03-28 09:49 39 ********************
... ..( 3 skipped). .. ********************
324 2017-03-28 09:53 39 ********************
325 2017-03-28 09:54 40 *********************
326 2017-03-28 09:55 39 ********************
327 2017-03-28 09:56 40 *********************
... ..( 14 skipped). .. *********************
342 2017-03-28 10:11 40 *********************
343 2017-03-28 10:12 41 **********************
... ..( 38 skipped). .. **********************
382 2017-03-28 10:51 41 **********************
383 2017-03-28 10:52 42 ***********************
... ..( 21 skipped). .. ***********************
405 2017-03-28 11:14 42 ***********************
406 2017-03-28 11:15 43 ************************
... ..( 55 skipped). .. ************************
462 2017-03-28 12:11 43 ************************
463 2017-03-28 12:12 44 *************************
464 2017-03-28 12:13 44 *************************
465 2017-03-28 12:14 43 ************************
466 2017-03-28 12:15 43 ************************
467 2017-03-28 12:16 44 *************************
... ..( 9 skipped). .. *************************
477 2017-03-28 12:26 44 *************************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11) not supported
pem@Serveur1:~$ sudo smartctl -x /dev/sdf
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4M6JVE6ZH
LU WWN Device Id: 5 0014ee 2b876baed
Firmware Version: 82.00A82
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Mar 28 12:26:19 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (26280) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 266) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 173 172 021 - 4333
4 Start_Stop_Count -O--CK 100 100 000 - 9
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 400
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 9
192 Power-Off_Retract_Count -O--CK 200 200 000 - 4
193 Load_Cycle_Count -O--CK 200 200 000 - 455
194 Temperature_Celsius -O---K 104 095 000 - 43
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 43 Celsius
Power Cycle Min/Max Temperature: 24/52 Celsius
Lifetime Min/Max Temperature: 18/52 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (83)
Index Estimated Time Temperature Celsius
84 2017-03-28 04:29 41 **********************
... ..( 19 skipped). .. **********************
104 2017-03-28 04:49 41 **********************
105 2017-03-28 04:50 40 *********************
... ..( 22 skipped). .. *********************
128 2017-03-28 05:13 40 *********************
129 2017-03-28 05:14 39 ********************
... ..( 3 skipped). .. ********************
133 2017-03-28 05:18 39 ********************
134 2017-03-28 05:19 40 *********************
... ..( 25 skipped). .. *********************
160 2017-03-28 05:45 40 *********************
161 2017-03-28 05:46 39 ********************
... ..( 21 skipped). .. ********************
183 2017-03-28 06:08 39 ********************
184 2017-03-28 06:09 38 *******************
... ..( 14 skipped). .. *******************
199 2017-03-28 06:24 38 *******************
200 2017-03-28 06:25 39 ********************
201 2017-03-28 06:26 39 ********************
202 2017-03-28 06:27 38 *******************
... ..( 20 skipped). .. *******************
223 2017-03-28 06:48 38 *******************
224 2017-03-28 06:49 37 ******************
... ..( 80 skipped). .. ******************
305 2017-03-28 08:10 37 ******************
306 2017-03-28 08:11 36 *****************
... ..( 66 skipped). .. *****************
373 2017-03-28 09:18 36 *****************
374 2017-03-28 09:19 37 ******************
... ..( 46 skipped). .. ******************
421 2017-03-28 10:06 37 ******************
422 2017-03-28 10:07 38 *******************
... ..( 4 skipped). .. *******************
427 2017-03-28 10:12 38 *******************
428 2017-03-28 10:13 39 ********************
... ..( 8 skipped). .. ********************
437 2017-03-28 10:22 39 ********************
438 2017-03-28 10:23 40 *********************
... ..( 17 skipped). .. *********************
456 2017-03-28 10:41 40 *********************
457 2017-03-28 10:42 41 **********************
... ..( 30 skipped). .. **********************
10 2017-03-28 11:13 41 **********************
11 2017-03-28 11:14 42 ***********************
... ..( 26 skipped). .. ***********************
38 2017-03-28 11:41 42 ***********************
39 2017-03-28 11:42 43 ************************
... ..( 43 skipped). .. ************************
83 2017-03-28 12:26 43 ************************
SCT Error Recovery Control:
Read: 70 (7,0 seconds)
Write: 70 (7,0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 9 --- Lifetime Power-On Resets
0x01 0x010 4 400 --- Power-on Hours
0x01 0x018 6 8083982900 --- Logical Sectors Written
0x01 0x020 6 11079922 --- Number of Write Commands
0x01 0x028 6 30862644 --- Logical Sectors Read
0x01 0x030 6 268242 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 396 --- Spindle Motor Power-on Hours
0x03 0x010 4 160 --- Head Flying Hours
0x03 0x018 4 460 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 42 --- Current Temperature
0x05 0x010 1 40 --- Average Short Term Temperature
0x05 0x018 1 - --- Average Long Term Temperature
0x05 0x020 1 51 --- Highest Temperature
0x05 0x028 1 18 --- Lowest Temperature
0x05 0x030 1 41 --- Highest Average Short Term Temperature
0x05 0x038 1 20 --- Lowest Average Short Term Temperature
0x05 0x040 1 - --- Highest Average Long Term Temperature
0x05 0x048 1 - --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 72 --- Number of Hardware Resets
0x06 0x010 4 329 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 25 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 25 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1038044 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sdg
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00J2GB0
Serial Number: WD-WCAYY0028606
LU WWN Device Id: 5 0014ee 2045d3744
Firmware Version: 80.00A80
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 28 12:26:22 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (38760) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 442) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3031) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 158 152 021 - 9066
4 Start_Stop_Count -O--CK 100 100 000 - 251
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 100 253 000 - 0
9 Power_On_Hours -O--CK 077 077 000 - 17221
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 249
192 Power-Off_Retract_Count -O--CK 200 200 000 - 174
193 Load_Cycle_Count -O--CK 061 061 000 - 417903
194 Temperature_Celsius -O---K 104 082 000 - 48
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 48 Celsius
Power Cycle Min/Max Temperature: 35/56 Celsius
Lifetime Min/Max Temperature: 44/70 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (236)
Index Estimated Time Temperature Celsius
237 2017-03-28 04:29 39 ********************
... ..( 33 skipped). .. ********************
271 2017-03-28 05:03 39 ********************
272 2017-03-28 05:04 38 *******************
273 2017-03-28 05:05 39 ********************
... ..( 9 skipped). .. ********************
283 2017-03-28 05:15 39 ********************
284 2017-03-28 05:16 38 *******************
285 2017-03-28 05:17 38 *******************
286 2017-03-28 05:18 39 ********************
... ..( 4 skipped). .. ********************
291 2017-03-28 05:23 39 ********************
292 2017-03-28 05:24 38 *******************
293 2017-03-28 05:25 39 ********************
294 2017-03-28 05:26 38 *******************
295 2017-03-28 05:27 38 *******************
296 2017-03-28 05:28 39 ********************
... ..( 12 skipped). .. ********************
309 2017-03-28 05:41 39 ********************
310 2017-03-28 05:42 38 *******************
311 2017-03-28 05:43 39 ********************
... ..( 5 skipped). .. ********************
317 2017-03-28 05:49 39 ********************
318 2017-03-28 05:50 38 *******************
319 2017-03-28 05:51 38 *******************
320 2017-03-28 05:52 39 ********************
321 2017-03-28 05:53 38 *******************
322 2017-03-28 05:54 38 *******************
323 2017-03-28 05:55 38 *******************
324 2017-03-28 05:56 39 ********************
325 2017-03-28 05:57 39 ********************
326 2017-03-28 05:58 38 *******************
327 2017-03-28 05:59 39 ********************
328 2017-03-28 06:00 39 ********************
329 2017-03-28 06:01 39 ********************
330 2017-03-28 06:02 38 *******************
331 2017-03-28 06:03 39 ********************
... ..( 23 skipped). .. ********************
355 2017-03-28 06:27 39 ********************
356 2017-03-28 06:28 40 *********************
... ..( 2 skipped). .. *********************
359 2017-03-28 06:31 40 *********************
360 2017-03-28 06:32 41 **********************
361 2017-03-28 06:33 40 *********************
362 2017-03-28 06:34 40 *********************
363 2017-03-28 06:35 40 *********************
364 2017-03-28 06:36 41 **********************
365 2017-03-28 06:37 40 *********************
... ..( 2 skipped). .. *********************
368 2017-03-28 06:40 40 *********************
369 2017-03-28 06:41 41 **********************
... ..( 5 skipped). .. **********************
375 2017-03-28 06:47 41 **********************
376 2017-03-28 06:48 42 ***********************
377 2017-03-28 06:49 42 ***********************
378 2017-03-28 06:50 42 ***********************
379 2017-03-28 06:51 41 **********************
380 2017-03-28 06:52 42 ***********************
... ..( 4 skipped). .. ***********************
385 2017-03-28 06:57 42 ***********************
386 2017-03-28 06:58 43 ************************
387 2017-03-28 06:59 43 ************************
388 2017-03-28 07:00 42 ***********************
389 2017-03-28 07:01 43 ************************
390 2017-03-28 07:02 42 ***********************
391 2017-03-28 07:03 43 ************************
... ..( 2 skipped). .. ************************
394 2017-03-28 07:06 43 ************************
395 2017-03-28 07:07 44 *************************
396 2017-03-28 07:08 43 ************************
397 2017-03-28 07:09 44 *************************
... ..( 6 skipped). .. *************************
404 2017-03-28 07:16 44 *************************
405 2017-03-28 07:17 45 **************************
406 2017-03-28 07:18 44 *************************
407 2017-03-28 07:19 44 *************************
408 2017-03-28 07:20 44 *************************
409 2017-03-28 07:21 45 **************************
... ..( 5 skipped). .. **************************
415 2017-03-28 07:27 45 **************************
416 2017-03-28 07:28 46 ***************************
417 2017-03-28 07:29 45 **************************
418 2017-03-28 07:30 46 ***************************
... ..( 12 skipped). .. ***************************
431 2017-03-28 07:43 46 ***************************
432 2017-03-28 07:44 47 ****************************
... ..( 3 skipped). .. ****************************
436 2017-03-28 07:48 47 ****************************
437 2017-03-28 07:49 46 ***************************
438 2017-03-28 07:50 47 ****************************
... ..( 17 skipped). .. ****************************
456 2017-03-28 08:08 47 ****************************
457 2017-03-28 08:09 48 *****************************
458 2017-03-28 08:10 48 *****************************
459 2017-03-28 08:11 48 *****************************
460 2017-03-28 08:12 47 ****************************
... ..( 5 skipped). .. ****************************
466 2017-03-28 08:18 47 ****************************
467 2017-03-28 08:19 46 ***************************
... ..( 4 skipped). .. ***************************
472 2017-03-28 08:24 46 ***************************
473 2017-03-28 08:25 47 ****************************
... ..( 8 skipped). .. ****************************
4 2017-03-28 08:34 47 ****************************
5 2017-03-28 08:35 48 *****************************
6 2017-03-28 08:36 48 *****************************
7 2017-03-28 08:37 48 *****************************
8 2017-03-28 08:38 47 ****************************
9 2017-03-28 08:39 48 *****************************
... ..( 16 skipped). .. *****************************
26 2017-03-28 08:56 48 *****************************
27 2017-03-28 08:57 49 ******************************
28 2017-03-28 08:58 48 *****************************
29 2017-03-28 08:59 49 ******************************
30 2017-03-28 09:00 48 *****************************
31 2017-03-28 09:01 48 *****************************
32 2017-03-28 09:02 47 ****************************
... ..( 34 skipped). .. ****************************
67 2017-03-28 09:37 47 ****************************
68 2017-03-28 09:38 46 ***************************
69 2017-03-28 09:39 47 ****************************
... ..( 6 skipped). .. ****************************
76 2017-03-28 09:46 47 ****************************
77 2017-03-28 09:47 46 ***************************
78 2017-03-28 09:48 46 ***************************
79 2017-03-28 09:49 47 ****************************
80 2017-03-28 09:50 46 ***************************
... ..( 4 skipped). .. ***************************
85 2017-03-28 09:55 46 ***************************
86 2017-03-28 09:56 47 ****************************
87 2017-03-28 09:57 46 ***************************
... ..( 2 skipped). .. ***************************
90 2017-03-28 10:00 46 ***************************
91 2017-03-28 10:01 47 ****************************
92 2017-03-28 10:02 46 ***************************
... ..( 30 skipped). .. ***************************
123 2017-03-28 10:33 46 ***************************
124 2017-03-28 10:34 45 **************************
125 2017-03-28 10:35 45 **************************
126 2017-03-28 10:36 46 ***************************
127 2017-03-28 10:37 46 ***************************
128 2017-03-28 10:38 45 **************************
129 2017-03-28 10:39 46 ***************************
130 2017-03-28 10:40 45 **************************
131 2017-03-28 10:41 45 **************************
132 2017-03-28 10:42 45 **************************
133 2017-03-28 10:43 46 ***************************
134 2017-03-28 10:44 45 **************************
... ..( 34 skipped). .. **************************
169 2017-03-28 11:19 45 **************************
170 2017-03-28 11:20 44 *************************
171 2017-03-28 11:21 44 *************************
172 2017-03-28 11:22 45 **************************
... ..( 6 skipped). .. **************************
179 2017-03-28 11:29 45 **************************
180 2017-03-28 11:30 44 *************************
181 2017-03-28 11:31 44 *************************
182 2017-03-28 11:32 43 ************************
... ..( 4 skipped). .. ************************
187 2017-03-28 11:37 43 ************************
188 2017-03-28 11:38 42 ***********************
... ..( 4 skipped). .. ***********************
193 2017-03-28 11:43 42 ***********************
194 2017-03-28 11:44 41 **********************
... ..( 14 skipped). .. **********************
209 2017-03-28 11:59 41 **********************
210 2017-03-28 12:00 40 *********************
... ..( 2 skipped). .. *********************
213 2017-03-28 12:03 40 *********************
214 2017-03-28 12:04 41 **********************
215 2017-03-28 12:05 40 *********************
... ..( 14 skipped). .. *********************
230 2017-03-28 12:20 40 *********************
231 2017-03-28 12:21 39 ********************
... ..( 4 skipped). .. ********************
236 2017-03-28 12:26 39 ********************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 25 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 1038013 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sdh
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Green
Device Model: WDC WD20EARX-00PASB0
Serial Number: WD-WMAZA5280732
LU WWN Device Id: 5 0014ee 002ca250c
Firmware Version: 51.0AB51
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Mar 28 12:26:24 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 363) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 169 158 021 - 6541
4 Start_Stop_Count -O--CK 100 100 000 - 154
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 084 084 000 - 12110
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 152
192 Power-Off_Retract_Count -O--CK 200 200 000 - 116
193 Load_Cycle_Count -O--CK 122 122 000 - 235897
194 Temperature_Celsius -O---K 108 088 000 - 42
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 2
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 2992 -
# 2 Short offline Completed without error 00% 435 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 28/49 Celsius
Lifetime Min/Max Temperature: 28/62 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (339)
Index Estimated Time Temperature Celsius
340 2017-03-28 04:29 41 **********************
... ..( 24 skipped). .. **********************
365 2017-03-28 04:54 41 **********************
366 2017-03-28 04:55 40 *********************
... ..( 26 skipped). .. *********************
393 2017-03-28 05:22 40 *********************
394 2017-03-28 05:23 41 **********************
... ..( 16 skipped). .. **********************
411 2017-03-28 05:40 41 **********************
412 2017-03-28 05:41 34 ***************
413 2017-03-28 05:42 34 ***************
414 2017-03-28 05:43 35 ****************
... ..( 2 skipped). .. ****************
417 2017-03-28 05:46 35 ****************
418 2017-03-28 05:47 34 ***************
419 2017-03-28 05:48 35 ****************
420 2017-03-28 05:49 34 ***************
... ..( 2 skipped). .. ***************
423 2017-03-28 05:52 34 ***************
424 2017-03-28 05:53 35 ****************
425 2017-03-28 05:54 34 ***************
... ..( 12 skipped). .. ***************
438 2017-03-28 06:07 34 ***************
439 2017-03-28 06:08 35 ****************
440 2017-03-28 06:09 34 ***************
... ..( 21 skipped). .. ***************
462 2017-03-28 06:31 34 ***************
463 2017-03-28 06:32 33 **************
464 2017-03-28 06:33 33 **************
465 2017-03-28 06:34 34 ***************
466 2017-03-28 06:35 33 **************
467 2017-03-28 06:36 33 **************
468 2017-03-28 06:37 33 **************
469 2017-03-28 06:38 34 ***************
470 2017-03-28 06:39 34 ***************
471 2017-03-28 06:40 33 **************
... ..( 2 skipped). .. **************
474 2017-03-28 06:43 33 **************
475 2017-03-28 06:44 34 ***************
476 2017-03-28 06:45 33 **************
... ..( 7 skipped). .. **************
6 2017-03-28 06:53 33 **************
7 2017-03-28 06:54 34 ***************
8 2017-03-28 06:55 33 **************
... ..(104 skipped). .. **************
113 2017-03-28 08:40 33 **************
114 2017-03-28 08:41 32 *************
115 2017-03-28 08:42 33 **************
116 2017-03-28 08:43 33 **************
117 2017-03-28 08:44 33 **************
118 2017-03-28 08:45 32 *************
119 2017-03-28 08:46 32 *************
120 2017-03-28 08:47 33 **************
121 2017-03-28 08:48 33 **************
122 2017-03-28 08:49 32 *************
123 2017-03-28 08:50 32 *************
124 2017-03-28 08:51 32 *************
125 2017-03-28 08:52 33 **************
126 2017-03-28 08:53 32 *************
... ..( 27 skipped). .. *************
154 2017-03-28 09:21 32 *************
155 2017-03-28 09:22 33 **************
156 2017-03-28 09:23 32 *************
... ..( 61 skipped). .. *************
218 2017-03-28 10:25 32 *************
219 2017-03-28 10:26 33 **************
220 2017-03-28 10:27 32 *************
... ..( 7 skipped). .. *************
228 2017-03-28 10:35 32 *************
229 2017-03-28 10:36 33 **************
230 2017-03-28 10:37 32 *************
... ..( 5 skipped). .. *************
236 2017-03-28 10:43 32 *************
237 2017-03-28 10:44 33 **************
238 2017-03-28 10:45 32 *************
239 2017-03-28 10:46 33 **************
240 2017-03-28 10:47 32 *************
... ..( 7 skipped). .. *************
248 2017-03-28 10:55 32 *************
249 2017-03-28 10:56 33 **************
250 2017-03-28 10:57 32 *************
251 2017-03-28 10:58 32 *************
252 2017-03-28 10:59 32 *************
253 2017-03-28 11:00 33 **************
... ..( 15 skipped). .. **************
269 2017-03-28 11:16 33 **************
270 2017-03-28 11:17 34 ***************
... ..( 4 skipped). .. ***************
275 2017-03-28 11:22 34 ***************
276 2017-03-28 11:23 35 ****************
277 2017-03-28 11:24 35 ****************
278 2017-03-28 11:25 36 *****************
279 2017-03-28 11:26 36 *****************
280 2017-03-28 11:27 36 *****************
281 2017-03-28 11:28 35 ****************
282 2017-03-28 11:29 36 *****************
... ..( 12 skipped). .. *****************
295 2017-03-28 11:42 36 *****************
296 2017-03-28 11:43 37 ******************
... ..( 7 skipped). .. ******************
304 2017-03-28 11:51 37 ******************
305 2017-03-28 11:52 38 *******************
... ..( 6 skipped). .. *******************
312 2017-03-28 11:59 38 *******************
313 2017-03-28 12:00 39 ********************
... ..( 8 skipped). .. ********************
322 2017-03-28 12:09 39 ********************
323 2017-03-28 12:10 40 *********************
... ..( 14 skipped). .. *********************
338 2017-03-28 12:25 40 *********************
339 2017-03-28 12:26 41 **********************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 25 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 1038068 Vendor specific
pem@Serveur1:~$ sudo smartctl -x /dev/sdi
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-70-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WCAZA0693841
LU WWN Device Id: 5 0014ee 2af98f74f
Firmware Version: 51.0AB51
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 28 12:26:29 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (38580) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 372) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 253 253 021 - 1016
4 Start_Stop_Count -O--CK 100 100 000 - 184
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 083 083 000 - 12898
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 182
192 Power-Off_Retract_Count -O--CK 200 200 000 - 136
193 Load_Cycle_Count -O--CK 108 108 000 - 276372
194 Temperature_Celsius -O---K 105 084 000 - 45
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 197 000 - 4
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 6
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 [5] occurred at disk power-on lifetime: 517 hours (21 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 15 8d 99 ef e0 00 Error: UNC 8 sectors at LBA = 0x158d99ef = 361601519
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 15 8d 99 ef e0 00 00:23:15.510 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:15.510 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:23:15.489 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:23:15.489 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:15.489 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 5 [4] occurred at disk power-on lifetime: 517 hours (21 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 15 8d 99 ef e0 00 Error: UNC 8 sectors at LBA = 0x158d99ef = 361601519
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 15 8d 99 ef e0 00 00:23:12.812 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:12.812 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:23:12.792 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:23:12.792 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:12.792 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 4 [3] occurred at disk power-on lifetime: 517 hours (21 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 15 8d 99 ef e0 00 Error: UNC 8 sectors at LBA = 0x158d99ef = 361601519
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 15 8d 99 ef e0 00 00:23:10.115 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:10.115 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:23:10.094 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:23:10.094 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:10.094 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3 [2] occurred at disk power-on lifetime: 517 hours (21 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 15 8d 99 ef e0 00 Error: UNC 8 sectors at LBA = 0x158d99ef = 361601519
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 15 8d 99 ef e0 00 00:23:07.407 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:07.407 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:23:07.387 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:23:07.387 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:07.387 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 2 [1] occurred at disk power-on lifetime: 517 hours (21 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 15 8d 99 ef e0 00 Error: UNC 8 sectors at LBA = 0x158d99ef = 361601519
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 15 8d 99 ef e0 00 00:23:04.700 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:04.700 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:23:04.679 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:23:04.679 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:23:04.679 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 1 [0] occurred at disk power-on lifetime: 517 hours (21 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 15 8d 99 ef e0 00 Error: UNC 8 sectors at LBA = 0x158d99ef = 361601519
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 15 8d 99 ef e0 00 00:23:02.001 READ DMA EXT
25 00 00 00 08 00 00 15 80 ab 2f e0 00 00:23:01.995 READ DMA EXT
25 00 00 00 08 00 00 14 cc a4 3f e0 00 00:23:01.991 READ DMA EXT
25 00 00 00 08 00 00 14 35 3b bf e0 00 00:23:01.982 READ DMA EXT
ca 00 00 00 08 00 00 0d b0 fd e7 ed 00 00:23:01.777 WRITE DMA
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 3745 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 45 Celsius
Power Cycle Min/Max Temperature: 30/52 Celsius
Lifetime Min/Max Temperature: 30/66 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (172)
Index Estimated Time Temperature Celsius
173 2017-03-28 04:29 43 ************************
... ..( 11 skipped). .. ************************
185 2017-03-28 04:41 43 ************************
186 2017-03-28 04:42 44 *************************
... ..( 10 skipped). .. *************************
197 2017-03-28 04:53 44 *************************
198 2017-03-28 04:54 45 **************************
... ..( 2 skipped). .. **************************
201 2017-03-28 04:57 45 **************************
202 2017-03-28 04:58 44 *************************
... ..( 26 skipped). .. *************************
229 2017-03-28 05:25 44 *************************
230 2017-03-28 05:26 45 **************************
... ..( 13 skipped). .. **************************
244 2017-03-28 05:40 45 **************************
245 2017-03-28 05:41 39 ********************
... ..( 2 skipped). .. ********************
248 2017-03-28 05:44 39 ********************
249 2017-03-28 05:45 38 *******************
250 2017-03-28 05:46 38 *******************
251 2017-03-28 05:47 38 *******************
252 2017-03-28 05:48 39 ********************
253 2017-03-28 05:49 38 *******************
... ..( 2 skipped). .. *******************
256 2017-03-28 05:52 38 *******************
257 2017-03-28 05:53 39 ********************
258 2017-03-28 05:54 38 *******************
... ..( 29 skipped). .. *******************
288 2017-03-28 06:24 38 *******************
289 2017-03-28 06:25 37 ******************
290 2017-03-28 06:26 37 ******************
291 2017-03-28 06:27 38 *******************
... ..( 2 skipped). .. *******************
294 2017-03-28 06:30 38 *******************
295 2017-03-28 06:31 37 ******************
296 2017-03-28 06:32 37 ******************
297 2017-03-28 06:33 37 ******************
298 2017-03-28 06:34 38 *******************
299 2017-03-28 06:35 37 ******************
300 2017-03-28 06:36 37 ******************
301 2017-03-28 06:37 37 ******************
302 2017-03-28 06:38 38 *******************
303 2017-03-28 06:39 37 ******************
... ..( 13 skipped). .. ******************
317 2017-03-28 06:53 37 ******************
318 2017-03-28 06:54 38 *******************
319 2017-03-28 06:55 37 ******************
... ..( 2 skipped). .. ******************
322 2017-03-28 06:58 37 ******************
323 2017-03-28 06:59 38 *******************
324 2017-03-28 07:00 37 ******************
... ..( 19 skipped). .. ******************
344 2017-03-28 07:20 37 ******************
345 2017-03-28 07:21 36 *****************
... ..( 4 skipped). .. *****************
350 2017-03-28 07:26 36 *****************
351 2017-03-28 07:27 37 ******************
352 2017-03-28 07:28 37 ******************
353 2017-03-28 07:29 36 *****************
354 2017-03-28 07:30 37 ******************
355 2017-03-28 07:31 37 ******************
356 2017-03-28 07:32 36 *****************
... ..( 21 skipped). .. *****************
378 2017-03-28 07:54 36 *****************
379 2017-03-28 07:55 37 ******************
380 2017-03-28 07:56 36 *****************
... ..( 2 skipped). .. *****************
383 2017-03-28 07:59 36 *****************
384 2017-03-28 08:00 37 ******************
385 2017-03-28 08:01 36 *****************
... ..( 47 skipped). .. *****************
433 2017-03-28 08:49 36 *****************
434 2017-03-28 08:50 35 ****************
... ..( 4 skipped). .. ****************
439 2017-03-28 08:55 35 ****************
440 2017-03-28 08:56 36 *****************
441 2017-03-28 08:57 35 ****************
... ..( 7 skipped). .. ****************
449 2017-03-28 09:05 35 ****************
450 2017-03-28 09:06 36 *****************
451 2017-03-28 09:07 35 ****************
... ..( 7 skipped). .. ****************
459 2017-03-28 09:15 35 ****************
460 2017-03-28 09:16 36 *****************
461 2017-03-28 09:17 35 ****************
... ..( 3 skipped). .. ****************
465 2017-03-28 09:21 35 ****************
466 2017-03-28 09:22 36 *****************
467 2017-03-28 09:23 35 ****************
468 2017-03-28 09:24 35 ****************
469 2017-03-28 09:25 35 ****************
470 2017-03-28 09:26 36 *****************
471 2017-03-28 09:27 35 ****************
... ..( 13 skipped). .. ****************
7 2017-03-28 09:41 35 ****************
8 2017-03-28 09:42 34 ***************
9 2017-03-28 09:43 35 ****************
... ..( 17 skipped). .. ****************
27 2017-03-28 10:01 35 ****************
28 2017-03-28 10:02 34 ***************
29 2017-03-28 10:03 35 ****************
30 2017-03-28 10:04 35 ****************
31 2017-03-28 10:05 34 ***************
32 2017-03-28 10:06 35 ****************
... ..( 3 skipped). .. ****************
36 2017-03-28 10:10 35 ****************
37 2017-03-28 10:11 34 ***************
38 2017-03-28 10:12 34 ***************
39 2017-03-28 10:13 34 ***************
40 2017-03-28 10:14 35 ****************
... ..( 8 skipped). .. ****************
49 2017-03-28 10:23 35 ****************
50 2017-03-28 10:24 34 ***************
51 2017-03-28 10:25 35 ****************
... ..( 16 skipped). .. ****************
68 2017-03-28 10:42 35 ****************
69 2017-03-28 10:43 34 ***************
70 2017-03-28 10:44 35 ****************
71 2017-03-28 10:45 35 ****************
72 2017-03-28 10:46 36 *****************
73 2017-03-28 10:47 35 ****************
... ..( 10 skipped). .. ****************
84 2017-03-28 10:58 35 ****************
85 2017-03-28 10:59 36 *****************
86 2017-03-28 11:00 36 *****************
87 2017-03-28 11:01 35 ****************
88 2017-03-28 11:02 35 ****************
89 2017-03-28 11:03 36 *****************
90 2017-03-28 11:04 35 ****************
91 2017-03-28 11:05 36 *****************
... ..( 13 skipped). .. *****************
105 2017-03-28 11:19 36 *****************
106 2017-03-28 11:20 37 ******************
107 2017-03-28 11:21 37 ******************
108 2017-03-28 11:22 37 ******************
109 2017-03-28 11:23 38 *******************
... ..( 4 skipped). .. *******************
114 2017-03-28 11:28 38 *******************
115 2017-03-28 11:29 39 ********************
116 2017-03-28 11:30 39 ********************
117 2017-03-28 11:31 39 ********************
118 2017-03-28 11:32 38 *******************
119 2017-03-28 11:33 39 ********************
120 2017-03-28 11:34 39 ********************
121 2017-03-28 11:35 39 ********************
122 2017-03-28 11:36 40 *********************
123 2017-03-28 11:37 39 ********************
... ..( 2 skipped). .. ********************
126 2017-03-28 11:40 39 ********************
127 2017-03-28 11:41 40 *********************
... ..( 14 skipped). .. *********************
142 2017-03-28 11:56 40 *********************
143 2017-03-28 11:57 41 **********************
... ..( 8 skipped). .. **********************
152 2017-03-28 12:06 41 **********************
153 2017-03-28 12:07 42 ***********************
... ..( 11 skipped). .. ***********************
165 2017-03-28 12:19 42 ***********************
166 2017-03-28 12:20 43 ************************
... ..( 5 skipped). .. ************************
172 2017-03-28 12:26 43 ************************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 25 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 1038052 Vendor specific
pem@Serveur1:~$Peut etre que j'ai mal vu mais tous les disques présentent 0 secteurs réalloués :
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0Dernière modification par pem1664 (Le 28/03/2017, à 11:33)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#21 Le 28/03/2017, à 11:35
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Bougron a écrit :
Mais, il serait possible que cela soit un bug? https://bugs.launchpad.net/ubuntu/+sour … ug/1359706
Je viens de voir ton lien, pourquoi pas mais je suis sous ubuntu 16.04 ca n'aurait pas été corrigé depuis?
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#22 Le 28/03/2017, à 11:52
- pem1664
Re : Raid 5 et mdadm [RESOLU]
C'était interressant cette discussion https://up-community.org/forum/public-u … mcblk0rpmb
je suis en train de lancer un
badblocks -b 4096 -c 4096 -s /dev/md0en revanche je ne suis pas sur des valeurs de clusters
webmin me dit : Chunk size 512 kB je dois remplacer 4096 par 512k alors?
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#23 Le 28/03/2017, à 12:06
- Bougron
Re : Raid 5 et mdadm [RESOLU]
fais badblock --help
Tu va voir qu'il s'agit de la taille physique des blocks des disques Sans mettre l'option la valeur par défault est 1024 or tes disques sont certainement tous en 4096 (voir le smartcl)
Je viens de voir une autre piste https://forums.resin.io/t/beaglebone-gr … lockup/560
qui n'est pas sur du RAIDS, Mais il est dit
"This causes the kernel to more aggressively reclaim memory and reduce fragmentation. "
C'est une piste possible et qui n'aurait donc rien a voir avec la qualité du RAIDS mais son remplissage.. resterait a trouver le paramétrage pour le RAIDS et pas pour du EMMC.
Je continue de chercher. Mais tu pourrais te préparer à ouvrir un bug dans launchpad si cela se renouvelle
et une trace semblable pour un simple disque dur en bon état. https://ubuntuforums.org/showthread.php?t=2326700 Je crois plus en plus à un problème logiciel
Il reste aussi la piste des secteurs de remplacement du RAID totalement pleine et plus d'espace pour ajouter une nouvelle entrée. Je ne sais pas trop comment on peut regarder cela
Dernière modification par Bougron (Le 28/03/2017, à 12:23)
Hors ligne
#24 Le 28/03/2017, à 12:18
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Merci Bougron pour ton aide, j'ai lancé badblocks comme cité dessus et pour l'instant il trouve bel et bien des erreurs...
pour l'instant
4.24% effectué, 27:52 écoulé. (38452/0/0 erreurs)J'ai comme l'impression que c'est pas prêt d'etre fini...
En revanche comme il est dit dans ton lien il faudrait que je crée un nouveau fichier fix-mmc-bbb.conf ?
You can try the following to fix it:
add the following contents in /etc/sysctl.d/fix-mmc-bbb.conf
vm.min_free_kbytes=8192
vm.dirty_ratio=5
vm.dirty_background_ratio=10
Then reboot the device.Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne
#25 Le 28/03/2017, à 12:28
- pem1664
Re : Raid 5 et mdadm [RESOLU]
Bougron a écrit :
Il reste aussi la piste des secteurs de remplacement du RAID totalement pleine et plus d'espace pour ajouter une nouvelle entrée. Je ne sais pas trop comment on peut regarder cela
Ah non ca je ne crois pas
/dev/md0 13T 9,7T 2,4T 81% /media/Serveur1donc normalement il me reste 2,4To dessus et en plus la copie que je suis en train de faire remplace et fusionne les dossiers et fichiers existants donc normalement je devrais pas trop remplir le raid
EDIT
Ah j'avais pas compris tu parles des secteurs de remplacement, pas des secteurs du raid en général, pardon, j'avais mal lu et mal compris
Dernière modification par pem1664 (Le 28/03/2017, à 12:30)
Pas de problème sans solutions, mettre [résolu] dans son premier post permet de rechercher plus facilement une solution... ;)
Hors ligne