Pages : 1
#1 Le 13/10/2009, à 01:33
- lacxavier
Pas Connection WIFI,Carte BCM43XG,Kubuntu9.04
Bonjours
J'utilise Kubuntu 9.04. Ma carte WIFI est une Broadcom BCM43XG. J'ai installer le pilote natif
Broadcom B43 wireless driver (tester pas Ubuntu) et inclus dans cette distribution.
Ca ne fonctionne pas.
wland0 est inexistant. Sur windows et mandriva 2009.1 ca fonctionne.
J'envoie le résutat des commandes principales.
remi@asus:~$ cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=9.04
DISTRIB_CODENAME=jaunty
DISTRIB_DESCRIPTION="Ubuntu 9.04"
remi@asus:~$ lsusb
Bus 001 Device 004: ID 04b8:011e Seiko Epson Corp. Perfection 1660 Photo
Bus 001 Device 002: ID eb1a:2860 eMPIA Technology, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 045e:00e1 Microsoft Corp. Wireless Laser Mouse 6000 Reciever
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
remi@asus:~$ lspci
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:04.0 Mass storage controller: Integrated Technology Express, Inc. ITE 8211F Single Channel UDMA 133 (rev 11)
01:09.0 Network controller: Broadcom Corporation BCM43XG (rev 01)
02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
04:00.0 VGA compatible controller: nVidia Corporation GeForce 8500 GT (rev a1)
remi@asus:~$ lspci -nn | grep -i net
01:09.0 Network controller [0280]: Broadcom Corporation BCM43XG [14e4:4329] (rev 01)
02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit Ethernet Controller [8086:109a]
remi@asus:~$ sudo lshw -C network
[sudo] password for remi:
*-network
description: Ethernet interface
product: 82573L Gigabit Ethernet Controller
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 00
serial: 00:15:f2:53:fa:75
size: 100MB/s
capacity: 1GB/s
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=0.3.3.3-k6 duplex=full firmware=0.5-7 ip=192.168.1.100 latency=0 link=yes module=e1000e multicast=yes port=twisted pair speed=100MB/s
*-network
description: Network controller
product: BCM43XG
vendor: Broadcom Corporation
physical id: 9
bus info: pci@0000:01:09.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: bus_master
configuration: driver=b43-pci-bridge latency=64 module=ssb
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: pan0
serial: 82:52:50:2f:ae:34
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
remi@asus:~$ lsmod
Module Size Used by
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
video 25360 0
output 11008 1 video
lp 17156 0
em28xx_alsa 16136 0
saa7115 24496 0
v4l2_common 20992 1 saa7115
snd_hda_intel 435636 2
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 82948 3 em28xx_alsa,snd_hda_intel,snd_pcm_oss
snd_seq_dummy 10756 0
snd_seq_oss 37760 0
snd_seq_midi 14336 0
snd_rawmidi 29696 1 snd_seq_midi
b43 131484 0
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
mac80211 217208 1 b43
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 29704 2 snd_pcm,snd_seq
snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
em28xx 70312 1 em28xx_alsa
videodev 41600 1 em28xx
v4l1_compat 21764 1 videodev
compat_ioctl32 9344 1 em28xx
snd 62628 14 em28xx_alsa,snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
cfg80211 38032 1 mac80211
videobuf_vmalloc 14724 1 em28xx
iTCO_wdt 19108 0
iTCO_vendor_support 11652 1 iTCO_wdt
soundcore 15200 1 snd
led_class 12036 1 b43
videobuf_core 26500 2 em28xx,videobuf_vmalloc
ir_common 52228 1 em28xx
ppdev 15620 0
input_polldev 11912 1 b43
pcspkr 10496 0
tveeprom 20100 1 em28xx
snd_page_alloc 16904 2 snd_hda_intel,snd_pcm
parport_pc 40100 1
parport 42220 3 lp,ppdev,parport_pc
intel_agp 34108 0
agpgart 42696 1 intel_agp
usbhid 42336 0
ssb 41220 1 b43
e1000e 121136 0
floppy 64324 0
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
remi@asus:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.
remi@asus:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:f2:53:fa:75
inet adr:192.168.1.100 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::215:f2ff:fe53:fa75/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:958 erreurs:0 :0 overruns:0 frame:0
TX packets:915 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:100
Octets reçus:971159 (971.1 KB) Octets transmis:104662 (104.6 KB)
Mémoire:cbfe0000-cc000000
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:54 erreurs:0 :0 overruns:0 frame:0
TX packets:54 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:3340 (3.3 KB) Octets transmis:3340 (3.3 KB)
remi@asus:~$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
remi@asus:~$ uname -r -m
2.6.28-11-generic i686
remi@asus:~$ cat /etc/network/interfaces
auto lo
iface lo inet loopback
remi@asus:~$ nm-tool
NetworkManager Tool
State: connected
- Device: eth0 [Auto eth0] ----------------------------------------------------
Type: Wired
Driver: e1000e
State: connected
Default: yes
HW Address: 00:15:F2:53:FA:75
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.100
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.1
DNS: 24.200.241.37
DNS: 24.201.245.77
DNS: 24.200.243.189
remi@asus:~$Hors ligne
#2 Le 13/10/2009, à 08:28
- olivier1979
Re : Pas Connection WIFI,Carte BCM43XG,Kubuntu9.04
salut
c est pas le MOdule b43 que t as besoin pour t as carte, mais le wl.
fait les code suivant
sudo modprobe -rf b43
echo blacklist b43 | sudo tee -a /etc/modprobe.d/blacklist.conf
sudo modprobe wl
echo wl | sudo tee -a /etc/modules
iwconfigouvre ensuite ton fichier /etc/modules, et supprime la ligne: b43 (si jamais que se module est inséré, sinon il va etre charger pendent le démarage.
gksudo gedit /etc/modules
redémare aprés ton ordi, et esseye a te connecté, si t arrive pas a te connecté poste les code suivant
iwconfig
ifconfig
lsmod
sudo iwlist scan
cat /etc/network/interfaces
cat /etc/modulessalutation
olivier1979
s.v.p ne regarder pas mes faute d'orthographe, je vient d'un Forum allemand, et mon français et de loin pas parfait :-)
merci
Hors ligne
#3 Le 14/10/2009, à 01:45
- lacxavier
Re : Pas Connection WIFI,Carte BCM43XG,Kubuntu9.04
Bonjour olivier 1979
1- J'ai suivi tes instructions
2- Je t'envoie aussi les codes demandés.
3- En désintallant b43 je n'ai plus de drivers pour ma carte.
4- Ca ne fonctionne pas.
remi@asus:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.
remi@asus:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:f2:53:fa:75
inet adr:192.168.1.102 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::215:f2ff:fe53:fa75/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:100 erreurs:0 :0 overruns:0 frame:0
TX packets:116 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:100
Octets reçus:90178 (90.1 KB) Octets transmis:12995 (12.9 KB)
Mémoire:cbfe0000-cc000000
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:32 erreurs:0 :0 overruns:0 frame:0
TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:1800 (1.8 KB) Octets transmis:1800 (1.8 KB)
remi@asus:~$ lsmod
Module Size Used by
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
input_polldev 11912 0
video 25360 0
output 11008 1 video
wl 1489748 0
ieee80211_crypt 13444 1 wl
lp 17156 0
em28xx_alsa 16136 0
saa7115 24496 0
v4l2_common 20992 1 saa7115
snd_hda_intel 435636 2
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 82948 3 em28xx_alsa,snd_hda_intel,snd_pcm_oss
snd_seq_dummy 10756 0
snd_seq_oss 37760 0
snd_seq_midi 14336 0
snd_rawmidi 29696 1 snd_seq_midi
em28xx 70312 1 em28xx_alsa
videodev 41600 1 em28xx
v4l1_compat 21764 1 videodev
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
compat_ioctl32 9344 1 em28xx
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
videobuf_vmalloc 14724 1 em28xx
iTCO_wdt 19108 0
iTCO_vendor_support 11652 1 iTCO_wdt
snd_timer 29704 2 snd_pcm,snd_seq
snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
videobuf_core 26500 2 em28xx,videobuf_vmalloc
ir_common 52228 1 em28xx
ppdev 15620 0
tveeprom 20100 1 em28xx
snd 62628 14 em28xx_alsa,snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pcspkr 10496 0
intel_agp 34108 0
agpgart 42696 1 intel_agp
soundcore 15200 1 snd
parport_pc 40100 1
parport 42220 3 lp,ppdev,parport_pc
snd_page_alloc 16904 2 snd_hda_intel,snd_pcm
usbhid 42336 0
ssb 41220 0
e1000e 121136 0
floppy 64324 0
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
remi@asus:~$ sudo iwlist scan
[sudo] password for remi:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
remi@asus:~$ cat /etc/network/interfaces
auto lo
iface lo inet loopback
remi@asus:~$ cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
lp
wl
remi@asus:~$ lspci -nn | grep -i net
01:09.0 Network controller [0280]: Broadcom Corporation BCM43XG [14e4:4329] (rev 01)
02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit Ethernet Controller [8086:109a]Merci
lacxavier
Québec
Hors ligne
#4 Le 14/10/2009, à 18:39
- olivier1979
Re : Pas Connection WIFI,Carte BCM43XG,Kubuntu9.04
salut
install les restricte modules
sudo apt-get install linux-restricted-modules-$(uname -r)salutation
olivier1979
s.v.p ne regarder pas mes faute d'orthographe, je vient d'un Forum allemand, et mon français et de loin pas parfait :-)
merci
Hors ligne
#5 Le 17/10/2009, à 22:15
- lacxavier
Re : Pas Connection WIFI,Carte BCM43XG,Kubuntu9.04
Salut olivier 1979
J'ai repris tes 4 commandes suivantes.
sudo modprobe -rf b43
echo blacklist b43 | sudo tee -a /etc/modprobe.d/blacklist.conf
sudo modprobe wl
echo wl | sudo tee -a /etc/modules
J'ai modifié la première en enlevant le f car dans d'autres documentation
modprobe n'en avait pas. (sudo modprobe -r b43).
Le Wifi s'est mis a fonctionné.
J'ai redémarré mon ordi et plus de Wifi.
Vérifier Modules et blacklist, c'est ok.
Si je reprends les 4 commandes, pas de Wifi. Et l'ordi ne se ferme plus.
Sur mon autre disque avec Ubuntu9.04 avec les commandes le Wifi fonctionne sans problème.
J'utilse le driver STA de broadcom mis dans le Hardawe drivers sur les deux disques.
Merci
lacxavier
Hors ligne
Pages : 1