Toshiba U500 - bon driver mais wifi non géré

fanfan_85 · Le 27/09/2009, à 16:20

c'est parfait, ça marche, continues

hlnrichard · Le 27/09/2009, à 16:34

Non, ça ne marche pas. En particulier :

root@helene-laptop:~# ndiswrapper -l
net8192se : invalid driver!
root@helene-laptop:~# exit
exit

Veux-tu le résultat d'autres lignes de commande ?

fanfan_85 · Le 27/09/2009, à 16:47

Non, c'est bon.

Je me suis penché sur le problème de ta carte et il se trouve que si on arrive pas à la faire fonctionner avec ndiswrapper, il n'y a rien d'autre à essayer (pour le moment). Le problème est que le driver de ta carte n'a pas encore été mis sur ubuntu donc on peut rien faire.

Je souhaite juste voir une dernière chose (que je regarderai ce soir car là je dois aller faire une course), ça va te remettre au point de départ.

Tapes les commandes suivantes:

sudo -s
ndiswrapper -r net8192se
modprobe -r ndiswrapper
mv /home/helene/install_wifi/91_92_SE_Driver/Win2K/net8192se.sys /home/helene/install_wifi/91_92_SE_Driver/Win2K/rtl8192se.sys
ndiswrapper -i /home/helene/install_wifi/91_92_SE_Driver/Win2K/net8192se.inf
ndiswrapper -m
mv /etc/modprobe.d/ndiswrapper /etc/modprobe.d/ndiswrapper.conf
modprobe ndiswrapper
ndiswrapper -l
exit

A ce point, tu dois être revenu au point de départ. Maintenant tapes les commandes suivantes et envoies moi les résultats:

ifconfig
iwconfig
dmesg

Je reviens ce soir vers 21h, donc profites un peu de ton dimanche

Ciao

hlnrichard · Le 27/09/2009, à 16:51

Dans le doute, je te les donne :

helene@helene-laptop:~$ mv /home/helene/install_wifi/91_92_SE_Driver/Win2K/rtl8192se.sys /home/helene/install_wifi/91_92_SE_Driver/Win2K/net8192se.sys
mv: ne peut évaluer `/home/helene/install_wifi/91_92_SE_Driver/Win2K/rtl8192se.sys': Aucun fichier ou dossier de ce type

helene@helene-laptop:~$ sudo -s
[sudo] password for helene:

root@helene-laptop:~# ndiswrapper -r net8192se

root@helene-laptop:~# rm /etc/modprobe.d/ndiswrapper
rm: ne peut enlever `/etc/modprobe.d/ndiswrapper': Aucun fichier ou dossier de ce type

root@helene-laptop:~# modprobe -r ndiswrapper

root@helene-laptop:~# apt-get remove --purge ndiswrapper-utils-1.9
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances       
Lecture des informations d'état... Fait
Les paquets suivants ont été installés automatiquement et ne sont plus nécessaires :
  ndiswrapper-common linux-headers-2.6.28-11 linux-headers-2.6.28-11-generic
Veuillez utiliser « apt-get autoremove » pour les supprimer.
Les paquets suivants seront ENLEVÉS :
  ndisgtk* ndiswrapper-utils-1.9*
0 mis à jour, 0 nouvellement installés, 2 à enlever et 0 non mis à jour.
Après cette opération, 578ko d'espace disque seront libérés.
Souhaitez-vous continuer [O/n] ? O
(Lecture de la base de données... 143292 fichiers et répertoires déjà installés.)
Suppression de ndisgtk ...
Purge des fichiers de configuration de ndisgtk ...
Suppression de ndiswrapper-utils-1.9 ...
Traitement des actions différées (« triggers ») pour « man-db »...

root@helene-laptop:~# rm /etc/modprobe.d/ndiswrapper
rm: ne peut enlever `/etc/modprobe.d/ndiswrapper': Aucun fichier ou dossier de ce type

root@helene-laptop:~# rm -r /etc/ndiswrapper/

 root@helene-laptop:~# rm /lib/modules/`uname -r`/kernel/drivers/net/ndiswrapper/ndiswrapper.ko
rm: ne peut enlever `/lib/modules/2.6.28-15-generic/kernel/drivers/net/ndiswrapper/ndiswrapper.ko': Aucun fichier ou dossier de ce type

root@helene-laptop:~# apt-get install ndiswrapper-utils-1.9 ndisgtk
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances       
Lecture des informations d'état... Fait
Les paquets suivants ont été installés automatiquement et ne sont plus nécessaires :
  linux-headers-2.6.28-11 linux-headers-2.6.28-11-generic
Veuillez utiliser « apt-get autoremove » pour les supprimer.
Paquets suggérés :
  ndiswrapper-source
Les NOUVEAUX paquets suivants seront installés :
  ndisgtk ndiswrapper-utils-1.9
0 mis à jour, 2 nouvellement installés, 0 à enlever et 0 non mis à jour.
Il est nécessaire de prendre 0o/57,7ko dans les archives.
Après cette opération, 578ko d'espace disque supplémentaires seront utilisés.
Sélection du paquet ndiswrapper-utils-1.9 précédemment désélectionné.
(Lecture de la base de données... 143270 fichiers et répertoires déjà installés.)
Dépaquetage de ndiswrapper-utils-1.9 (à partir de .../ndiswrapper-utils-1.9_1.53-2ubuntu1_i386.deb) ...
Sélection du paquet ndisgtk précédemment désélectionné.
Dépaquetage de ndisgtk (à partir de .../ndisgtk_0.8.4-1_i386.deb) ...
Traitement des actions différées (« triggers ») pour « man-db »...
Paramétrage de ndiswrapper-utils-1.9 (1.53-2ubuntu1) ...
Paramétrage de ndisgtk (0.8.4-1) ...

root@helene-laptop:~# ndiswrapper -i /home/helene/install_wifi/91_92_SE_Driver/Win2K/net8192se.inf
installing net8192se ...
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete
couldn't find "rtl8192se.sys" in "/home/helene/install_wifi/91_92_SE_Driver/Win2K"; make sure all driver files, including .inf, .sys (and any firmware files) are in "/home/helene/install_wifi/91_92_SE_Driver/Win2K" -
installation may be incomplete

root@helene-laptop:~# ndiswrapper -m
module configuration already contains alias directive

root@helene-laptop:~# mv /etc/modprobe.d/ndiswrapper /etc/modprobe.d/ndiswrapper.conf
mv: ne peut évaluer `/etc/modprobe.d/ndiswrapper': Aucun fichier ou dossier de ce type

root@helene-laptop:~# modprobe ndiswrapper

root@helene-laptop:~# ndiswrapper -l
net8192se : invalid driver!
root@helene-laptop:~# exit
exit

Pourquoi ne trouve-t-il pas les drivers ? Faut-il que je crée un dossier propre dans mon répertoire avec tous les drivers ?

Merci pour ta réponse
hlnrichard

Pourquoi

hlnrichard · Le 27/09/2009, à 17:00

Merci beaucoup de m'avoir aidé.

L'informatique n'est pas une science exacte. Pourquoi d'autres utilisateurs du Toshiba U500 on pu faire fonctionner le wifi. Les cartes wifi peuvent-elles varier pour un même modèle ?
Y a-t-il un site où je puisse faire une veille concernant la résolution de ce problème ? Une solution est-elle cherchée par la communauté ?

Voici les résultats des commandes

eth0      Link encap:Ethernet  HWaddr 00:26:18:85:c0:12  
          inet adr:192.168.1.3  Bcast:192.168.1.255  Masque:255.255.255.0
          adr inet6: fe80::226:18ff:fe85:c012/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          Packets reçus:1390 erreurs:0 :0 overruns:0 frame:0
          TX packets:1595 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          Octets reçus:823609 (823.6 KB) Octets transmis:339010 (339.0 KB)
          Interruption:250 Adresse de base:0xa000 

lo        Link encap:Boucle locale  
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          Packets reçus:4 erreurs:0 :0 overruns:0 frame:0
          TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:0 
          Octets reçus:240 (240.0 B) Octets transmis:240 (240.0 B)

wlan0     Link encap:Ethernet  HWaddr 00:24:d2:df:ad:0a  
          adr inet6: fe80::224:d2ff:fedf:ad0a/64 Scope:Lien
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
          Interruption:17 Mémoire:fdffc000-fe000000 

wlan0:avahi Link encap:Ethernet  HWaddr 00:24:d2:df:ad:0a  
          inet adr:169.254.7.76  Bcast:169.254.255.255  Masque:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          Interruption:17 Mémoire:fdffc000-fe00000

lo        no wireless extensions.

eth0      no wireless extensions.

pan0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:off/any  
          Mode:Managed  Frequency:2.457 GHz  Access Point: Not-Associated   
          Bit Rate:130 Mb/s   Tx-Power:20 dBm   Sensitivity=0/3  
          RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Et le plus long pour la fin !

[    3.268393] usb usb3: configuration #1 chosen from 1 choice
[    3.268417] hub 3-0:1.0: USB hub found
[    3.268423] hub 3-0:1.0: 2 ports detected
[    3.268500] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    3.268516] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    3.268520] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    3.268564] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    3.268596] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a800
[    3.268662] usb usb4: configuration #1 chosen from 1 choice
[    3.268684] hub 4-0:1.0: USB hub found
[    3.268690] hub 4-0:1.0: 2 ports detected
[    3.268768] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    3.268775] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    3.268778] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    3.268814] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    3.268847] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000a480
[    3.268913] usb usb5: configuration #1 chosen from 1 choice
[    3.268937] hub 5-0:1.0: USB hub found
[    3.268942] hub 5-0:1.0: 2 ports detected
[    3.269021] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    3.269027] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    3.269030] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    3.269067] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    3.269093] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
[    3.269162] usb usb6: configuration #1 chosen from 1 choice
[    3.269184] hub 6-0:1.0: USB hub found
[    3.269189] hub 6-0:1.0: 2 ports detected
[    3.269267] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    3.269273] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    3.269276] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    3.269320] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    3.269345] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000
[    3.269413] usb usb7: configuration #1 chosen from 1 choice
[    3.269435] hub 7-0:1.0: USB hub found
[    3.269440] hub 7-0:1.0: 2 ports detected
[    3.269518] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.269524] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    3.269528] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.269566] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    3.269590] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ac00
[    3.269656] usb usb8: configuration #1 chosen from 1 choice
[    3.269681] hub 8-0:1.0: USB hub found
[    3.269687] hub 8-0:1.0: 2 ports detected
[    3.269816] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    3.278105] i8042.c: Detected active multiplexing controller, rev 1.1.
[    3.282523] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.282528] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    3.282530] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    3.282533] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    3.282535] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    3.284544] mice: PS/2 mouse device common for all mice
[    3.304569] rtc_cmos 00:06: RTC can wake from S4
[    3.304601] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    3.304631] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    3.304694] device-mapper: uevent: version 1.0.3
[    3.304786] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    3.304890] device-mapper: multipath: version 1.0.5 loaded
[    3.304892] device-mapper: multipath round-robin: version 1.0.0 loaded
[    3.304980] EISA: Probing bus 0 at eisa.0
[    3.305016] EISA: Detected 0 cards.
[    3.305148] cpuidle: using governor ladder
[    3.305258] cpuidle: using governor menu
[    3.305735] TCP cubic registered
[    3.305830] NET: Registered protocol family 10
[    3.306229] lo: Disabled Privacy Extensions
[    3.306535] NET: Registered protocol family 17
[    3.306551] Bluetooth: L2CAP ver 2.11
[    3.306553] Bluetooth: L2CAP socket layer initialized
[    3.306555] Bluetooth: SCO (Voice Link) ver 0.6
[    3.306557] Bluetooth: SCO socket layer initialized
[    3.306601] Bluetooth: RFCOMM socket layer initialized
[    3.306607] Bluetooth: RFCOMM TTY layer initialized
[    3.306608] Bluetooth: RFCOMM ver 1.10
[    3.307319] Using IPI No-Shortcut mode
[    3.307392] registered taskstats version 1
[    3.307514]   Magic number: 9:458:486
[    3.307598] rtc_cmos 00:06: setting system clock to 2009-09-27 14:27:20 UTC (1254061640)
[    3.307601] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    3.307603] EDD information not available.
[    3.307824] Freeing unused kernel memory: 532k freed
[    3.307946] Write protecting the kernel text: 4116k
[    3.308007] Write protecting the kernel read-only data: 1528k
[    3.311140] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    3.508552] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.508571] r8169 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    3.508590] r8169 0000:07:00.0: setting latency timer to 64
[    3.508701] r8169 0000:07:00.0: irq 2298 for MSI/MSI-X
[    3.509304] eth0: RTL8102e at 0xf7c6a000, 00:26:18:85:c0:12, XID 24c00000 IRQ 2298
[    3.580861] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    3.721797] usb 1-1: configuration #1 chosen from 1 choice
[    3.896033] PM: Starting manual resume from disk
[    3.896036] PM: Resume from partition 8:5
[    3.896038] PM: Checking hibernation image.
[    3.896206] PM: Resume from disk failed.
[    3.939057] kjournald starting.  Commit interval 5 seconds
[    3.939072] EXT3-fs: mounted filesystem with ordered data mode.
[    4.112081] usb 7-2: new low speed USB device using uhci_hcd and address 2
[    4.291478] usb 7-2: configuration #1 chosen from 1 choice
[    8.622543] udev: starting version 141
[    9.027817] Linux agpgart interface v0.103
[    9.090225] iTCO_vendor_support: vendor-support=0
[    9.132057] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[    9.132331] iTCO_wdt: Found a ICH9M TCO device (Version=2, TCOBASE=0x0860)
[    9.132434] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    9.183898] input: PC Speaker as /devices/platform/pcspkr/input/input6
[    9.226936] sdhci: Secure Digital Host Controller Interface driver
[    9.226940] sdhci: Copyright(c) Pierre Ossman
[    9.387511] agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset
[    9.387954] agpgart-intel 0000:00:00.0: detected 32764K stolen memory
[    9.391309] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    9.398803] usbcore: registered new interface driver hiddev
[    9.399048] usbcore: registered new interface driver usbhid
[    9.399079] usbhid: v2.6:USB HID core driver
[    9.420362] acpi device:04: registered as cooling_device8
[    9.420560] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/input/input7
[    9.426510] sdhci-pci 0000:02:00.0: SDHCI controller found [1180:e822] (rev 1)
[    9.426532] sdhci-pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    9.427566] sdhci-pci 0000:02:00.0: Will use DMA mode even though HW doesn't fully claim to support it.
[    9.427575] sdhci-pci 0000:02:00.0: setting latency timer to 64
[    9.428635] ACPI: Video Device [IGD] (multi-head: yes  rom: no  post: no)
[    9.428791] mmc0: SDHCI controller on PCI [0000:02:00.0] using DMA
[    9.449546] Linux video capture interface: v2.00
[    9.481046] uvcvideo: Found UVC 1.00 device USB2.0 UVC WebCam (04f2:b130)
[    9.501728] input: USB2.0 UVC WebCam as /devices/pci0000:00/0000:00:1a.7/usb1/1-1/1-1:1.0/input/input8
[    9.501967] usbcore: registered new interface driver uvcvideo
[    9.502006] USB Video Class driver (v0.1.0)
[    9.527723] input: Mitsumi Electric Apple Optical USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/input/input9
[    9.537536] apple 0003:05AC:0304.0001: input,hidraw0: USB HID v1.10 Mouse [Mitsumi Electric Apple Optical USB Mouse] on usb-0000:00:1d.1-2/input0
[    9.604883] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[    9.642242] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    9.642354] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    9.754276] hda_codec: Unknown model for ALC269, trying auto-probe from BIOS...
[    9.967602] psmouse serio2: ID: 73 02 64<6>input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio2/input/input10
[   10.756008] hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x011f1c00
[   10.976665] lp: driver loaded but no devices found
[   11.007436] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[   11.051063] ndiswrapper (load_wrap_driver:108): couldn't load driver net8192se; check system log for messages from 'loadndisdriver'
[   11.051122] usbcore: registered new interface driver ndiswrapper
[   11.247405] Adding 8964228k swap on /dev/sda5.  Priority:-1 extents:1 across:8964228k
[   11.784494] EXT3 FS on sda1, internal journal
[   12.875326] type=1505 audit(1254061650.064:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2209
[   12.919438] type=1505 audit(1254061650.108:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2213
[   12.919548] type=1505 audit(1254061650.108:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2213
[   12.919588] type=1505 audit(1254061650.108:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2213
[   12.919624] type=1505 audit(1254061650.108:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2213
[   13.042147] type=1505 audit(1254061650.232:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2218
[   13.042316] type=1505 audit(1254061650.232:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2218
[   13.068624] type=1505 audit(1254061650.260:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2222
[   17.213469] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.213472] Bluetooth: BNEP filters: protocol multicast
[   17.221624] Bridge firewalling registered
[   18.481627] ppdev: user-space parallel port driver
[   19.931113] [drm] Initialized drm 1.1.0 20060810
[   19.936053] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   19.936059] pci 0000:00:02.0: setting latency timer to 64
[   19.936253] pci 0000:00:02.0: irq 2297 for MSI/MSI-X
[   19.936347] [drm] Initialized i915 1.6.0 20080730 on minor 0
[   19.937612] [drm:i915_setparam] *ERROR* unknown parameter 4
[   22.807772] r8169: eth0: link up
[   22.807780] r8169: eth0: link up
[   33.264103] eth0: no IPv6 routers present
[   47.764567] CPU0 attaching NULL sched-domain.
[   47.764573] CPU1 attaching NULL sched-domain.
[   47.768092] CPU0 attaching sched-domain:
[   47.768095]  domain 0: span 0-1 level MC
[   47.768098]   groups: 0 1
[   47.768103] CPU1 attaching sched-domain:
[   47.768105]  domain 0: span 0-1 level MC
[   47.768108]   groups: 1 0
[  260.520164] usbcore: deregistering interface driver ndiswrapper
[  328.568332] ACPI: Transitioning device [FAN4] to D3
[  328.568337] ACPI: Unable to turn cooling device [f6c1af18] 'off'
[  349.836887] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[  349.872205] ndiswrapper (load_wrap_driver:108): couldn't load driver net8192se; check system log for messages from 'loadndisdriver'
[  349.872291] usbcore: registered new interface driver ndiswrapper
[  800.152359] CPU0 attaching NULL sched-domain.
[  800.152367] CPU1 attaching NULL sched-domain.
[  800.156414] CPU0 attaching sched-domain:
[  800.156418]  domain 0: span 0-1 level MC
[  800.156422]   groups: 0 1
[  800.156431] CPU1 attaching sched-domain:
[  800.156434]  domain 0: span 0-1 level MC
[  800.156438]   groups: 1 0
[  801.895677] [drm:gm45_get_vblank_counter] *ERROR* trying to get vblank count for disabled pipe 0
[  802.044095] PM: Syncing filesystems ... done.
[  802.063909] PM: Preparing system for mem sleep
[  802.063912] Freezing user space processes ... (elapsed 0.00 seconds) done.
[  802.064689] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[  802.064739] PM: Entering mem sleep
[  802.064749] Suspending console(s) (use no_console_suspend to debug)
[  802.742451] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[  802.742565] sd 1:0:0:0: [sda] Stopping disk
[  803.177461] ACPI handle has no context!
[  803.177468] r8169 0000:07:00.0: PME# enabled
[  803.177475] ACPI handle has no context!
[  803.193430] ACPI handle has no context!
[  803.193439] sdhci-pci 0000:02:00.0: PCI INT A disabled
[  803.193451] ACPI handle has no context!
[  803.288226] ehci_hcd 0000:00:1d.7: PCI INT A disabled
[  803.304128] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[  803.304176] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[  803.304225] uhci_hcd 0000:00:1d.0: PCI INT A disabled
[  803.320096] HDA Intel 0000:00:1b.0: PCI INT A disabled
[  803.320153] ACPI handle has no context!
[  803.336142] ehci_hcd 0000:00:1a.7: PCI INT C disabled
[  803.352128] uhci_hcd 0000:00:1a.2: PCI INT D disabled
[  803.352177] uhci_hcd 0000:00:1a.1: PCI INT B disabled
[  803.352225] uhci_hcd 0000:00:1a.0: PCI INT A disabled
[  803.352570] PM: suspend devices took 1.288 seconds
[  803.352715] ACPI: Preparing to enter system sleep state S3
[  803.353443] Disabling non-boot CPUs ...
[  803.456023] CPU 1 is now offline
[  803.456026] SMP alternatives: switching to UP code
[  803.588460] CPU0 attaching NULL sched-domain.
[  803.588463] CPU1 attaching NULL sched-domain.
[  803.588681] CPU0 attaching NULL sched-domain.
[  803.588820] CPU1 is down
[  803.588899] Extended CMOS year: 2000
[  803.588899] Back to C!
[  803.588899] Extended CMOS year: 2000
[  803.588899] Enabling non-boot CPUs ...
[  803.588899] SMP alternatives: switching to SMP code
[  803.717784] Booting processor 1 APIC 0x1 ip 0x6000
[  803.588344] Initializing CPU#1
[  803.588344] Calibrating delay using timer specific routine.. 3990.06 BogoMIPS (lpj=7980125)
[  803.588344] CPU: L1 I cache: 32K, L1 D cache: 32K
[  803.588344] CPU: L2 cache: 1024K
[  803.588344] CPU: Physical Processor ID: 0
[  803.588344] CPU: Processor Core ID: 1
[  803.808397] CPU1: Intel Pentium(R) Dual-Core CPU       T4200  @ 2.00GHz stepping 0a
[  803.808458] CPU0 attaching NULL sched-domain.
[  803.809073] CPU0 attaching sched-domain:
[  803.809076]  domain 0: span 0-1 level MC
[  803.809078]   groups: 0 1
[  803.809082] CPU1 attaching sched-domain:
[  803.809084]  domain 0: span 0-1 level MC
[  803.809085]   groups: 1 0
[  803.812021] Switched to high resolution mode on CPU 1
[  803.812032] CPU1 is up
[  803.812034] ACPI: Waking up from system sleep state S3
[  803.852744] ACPI: Transitioning device [FAN0] to D3
[  803.852746] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  803.856744] ACPI: Transitioning device [FAN1] to D3
[  803.856746] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  803.868743] ACPI: Transitioning device [FAN2] to D3
[  803.868744] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  803.876742] ACPI: Transitioning device [FAN3] to D3
[  803.876744] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  803.876777] pci 0000:00:02.0: restoring config space at offset 0x8 (was 0x1, writing 0xa401)
[  803.876784] pci 0000:00:02.0: restoring config space at offset 0x1 (was 0x900007, writing 0x900403)
[  803.880027] pci 0000:00:02.1: restoring config space at offset 0x4 (was 0x4, writing 0xfdc00004)
[  803.880034] pci 0000:00:02.1: restoring config space at offset 0x1 (was 0x900000, writing 0x900007)
[  803.880051] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  803.880058] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[  803.880119] usb usb3: root hub lost power or was reset
[  803.880138] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[  803.880143] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[  803.880203] usb usb4: root hub lost power or was reset
[  803.880220] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[  803.880225] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[  803.880284] usb usb5: root hub lost power or was reset
[  803.896086] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[  803.896091] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[  803.912116] HDA Intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
[  803.912122] HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
[  803.912142] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[  803.912148] HDA Intel 0000:00:1b.0: setting latency timer to 64
[  804.018412] pcieport-driver 0000:00:1c.0: restoring config space at offset 0xf (was 0x20100, writing 0x20105)
[  804.018440] pcieport-driver 0000:00:1c.0: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
[  804.018448] pcieport-driver 0000:00:1c.0: restoring config space at offset 0x1 (was 0x180106, writing 0x100506)
[  804.018496] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[  804.018520] pcieport-driver 0000:00:1c.1: restoring config space at offset 0xf (was 0x20200, writing 0x2020a)
[  804.018570] pcieport-driver 0000:00:1c.1: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
[  804.018579] pcieport-driver 0000:00:1c.1: restoring config space at offset 0x1 (was 0x180107, writing 0x100507)
[  804.018642] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[  804.018664] pcieport-driver 0000:00:1c.3: restoring config space at offset 0xf (was 0x20400, writing 0x2040b)
[  804.018686] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x7 (was 0x2000d0d0, writing 0xd0d0)
[  804.018698] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
[  804.018705] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[  804.018755] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[  804.018782] pcieport-driver 0000:00:1c.5: restoring config space at offset 0xf (was 0x20200, writing 0x2020a)
[  804.018826] pcieport-driver 0000:00:1c.5: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
[  804.018836] pcieport-driver 0000:00:1c.5: restoring config space at offset 0x1 (was 0x180107, writing 0x100507)
[  804.018885] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[  804.018895] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[  804.018900] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[  804.018959] usb usb6: root hub lost power or was reset
[  804.018978] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[  804.018983] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[  804.019042] usb usb7: root hub lost power or was reset
[  804.019061] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[  804.019068] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[  804.019131] usb usb8: root hub lost power or was reset
[  804.032083] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[  804.032088] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[  804.032151] pci 0000:00:1e.0: restoring config space at offset 0xf (was 0x20000, writing 0x200ff)
[  804.032206] pci 0000:00:1e.0: setting latency timer to 64
[  804.048116] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
[  804.048158] ahci 0000:00:1f.2: setting latency timer to 64
[  804.064106] sdhci-pci 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[  804.064135] sdhci-pci 0000:02:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xfdeffc00)
[  804.064142] sdhci-pci 0000:02:00.0: restoring config space at offset 0x3 (was 0x800000, writing 0x800008)
[  804.064150] sdhci-pci 0000:02:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100006)
[  804.064178] sdhci-pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  804.064181] sdhci-pci 0000:02:00.0: Will use DMA mode even though HW doesn't fully claim to support it.
[  804.064188] sdhci-pci 0000:02:00.0: setting latency timer to 64
[  804.065220] pci 0000:02:00.1: restoring config space at offset 0xf (was 0x200, writing 0x205)
[  804.065249] pci 0000:02:00.1: restoring config space at offset 0x4 (was 0x0, writing 0xfdeff800)
[  804.065255] pci 0000:02:00.1: restoring config space at offset 0x3 (was 0x800000, writing 0x800008)
[  804.065264] pci 0000:02:00.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100006)
[  804.065317] pci 0000:02:00.2: restoring config space at offset 0xf (was 0x300, writing 0x30e)
[  804.065346] pci 0000:02:00.2: restoring config space at offset 0x4 (was 0x0, writing 0xfdeff400)
[  804.065353] pci 0000:02:00.2: restoring config space at offset 0x3 (was 0x800000, writing 0x800008)
[  804.065361] pci 0000:02:00.2: restoring config space at offset 0x1 (was 0x100000, writing 0x100006)
[  804.065412] pci 0000:03:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x105)
[  804.065438] pci 0000:03:00.0: restoring config space at offset 0x5 (was 0x0, writing 0xfdffc000)
[  804.065444] pci 0000:03:00.0: restoring config space at offset 0x4 (was 0x1, writing 0xc801)
[  804.065450] pci 0000:03:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
[  804.065458] pci 0000:03:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
[  804.080103] r8169 0000:07:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x105)
[  804.080113] r8169 0000:07:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfebe0000)
[  804.080126] r8169 0000:07:00.0: restoring config space at offset 0x8 (was 0xc, writing 0xfcfe000c)
[  804.080134] r8169 0000:07:00.0: restoring config space at offset 0x6 (was 0xc, writing 0xfcfff00c)
[  804.080142] r8169 0000:07:00.0: restoring config space at offset 0x4 (was 0x1, writing 0xe801)
[  804.080149] r8169 0000:07:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
[  804.080157] r8169 0000:07:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
[  804.080221] r8169 0000:07:00.0: PME# disabled
[  804.080321] sd 1:0:0:0: [sda] Starting disk
[  804.368596] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  804.368623] ata6: SATA link down (SStatus 0 SControl 300)
[  804.368639] ata1: SATA link down (SStatus 0 SControl 300)
[  804.377157] ata5.00: configured for UDMA/133
[  805.544589] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  805.548953] ata2.00: configured for UDMA/100
[  805.564114] sd 1:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[  805.564130] sd 1:0:0:0: [sda] Write Protect is off
[  805.564132] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  805.564154] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  806.236041] usb 1-1: reset high speed USB device using ehci_hcd and address 2
[  806.672060] usb 7-2: reset low speed USB device using uhci_hcd and address 2
[  806.996078] pci 0000:00:02.0: setting latency timer to 64
[  806.997287] PM: resume devices took 3.168 seconds
[  806.997317] PM: Finishing wakeup.
[  806.997319] Restarting tasks ... done.
[  807.197786] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[  807.578513] r8169: eth0: link up
[  807.590074] psmouse serio2: ID: 73 02 64<7>CPU0 attaching NULL sched-domain.
[  808.568230] CPU1 attaching NULL sched-domain.
[  808.584069] CPU0 attaching sched-domain:
[  808.584072]  domain 0: span 0-1 level MC
[  808.584075]   groups: 0 1
[  808.584080] CPU1 attaching sched-domain:
[  808.584082]  domain 0: span 0-1 level MC
[  808.584084]   groups: 1 0
[  814.648325] ACPI: Transitioning device [FAN0] to D3
[  814.648330] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  814.660830] ACPI: Transitioning device [FAN1] to D3
[  814.660835] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  814.668840] ACPI: Transitioning device [FAN2] to D3
[  814.668844] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  814.680823] ACPI: Transitioning device [FAN3] to D3
[  814.680827] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  816.164842] ACPI: Transitioning device [FAN0] to D3
[  816.164847] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  816.169381] ACPI: Transitioning device [FAN1] to D3
[  816.169386] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  816.173324] ACPI: Transitioning device [FAN2] to D3
[  816.173328] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  816.177348] ACPI: Transitioning device [FAN3] to D3
[  816.177353] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  817.816028] eth0: no IPv6 routers present
[  832.084848] ACPI: Transitioning device [FAN0] to D3
[  832.084853] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  832.089205] ACPI: Transitioning device [FAN1] to D3
[  832.089208] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  832.093199] ACPI: Transitioning device [FAN2] to D3
[  832.093202] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  832.100806] ACPI: Transitioning device [FAN3] to D3
[  832.100811] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  833.596829] ACPI: Transitioning device [FAN0] to D3
[  833.596834] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  833.601161] ACPI: Transitioning device [FAN1] to D3
[  833.601165] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  833.604833] ACPI: Transitioning device [FAN2] to D3
[  833.604837] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  833.612837] ACPI: Transitioning device [FAN3] to D3
[  833.612841] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  978.880884] ACPI: Transitioning device [FAN0] to D3
[  978.880890] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  978.888875] ACPI: Transitioning device [FAN1] to D3
[  978.888880] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  978.896876] ACPI: Transitioning device [FAN2] to D3
[  978.896880] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  978.901213] ACPI: Transitioning device [FAN3] to D3
[  978.901217] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  978.905245] ACPI: Transitioning device [FAN4] to D3
[  978.905251] ACPI: Unable to turn cooling device [f6c1af18] 'off'
[  980.392922] ACPI: Transitioning device [FAN0] to D3
[  980.392927] ACPI: Unable to turn cooling device [f6c1ad38] 'off'
[  980.397345] ACPI: Transitioning device [FAN1] to D3
[  980.397350] ACPI: Unable to turn cooling device [f6c1adb0] 'off'
[  980.404848] ACPI: Transitioning device [FAN2] to D3
[  980.404853] ACPI: Unable to turn cooling device [f6c1ae28] 'off'
[  980.412851] ACPI: Transitioning device [FAN3] to D3
[  980.412856] ACPI: Unable to turn cooling device [f6c1aea0] 'off'
[  980.417434] ACPI: Transitioning device [FAN4] to D3
[  980.417439] ACPI: Unable to turn cooling device [f6c1af18] 'off'
[ 1523.992648] usbcore: deregistering interface driver ndiswrapper
[ 1566.320666] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[ 1566.342181] ndiswrapper: driver net8192se (Realtek Semiconductor Corp.,05/20/2009,1080.7.0520.2009) loaded
[ 1566.342520] ndiswrapper 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1566.342928] ndiswrapper 0000:03:00.0: setting latency timer to 64
[ 1566.572575] ndiswrapper: using IRQ 17
[ 1566.954278] wlan0: ethernet device 00:24:d2:df:ad:0a using NDIS driver: net8192se, version: 0x500a5, NDIS version: 0x500, vendor: 'Realtek RTL8192SE Wireless LAN PCI-E NIC                                     ', 10EC:8172.5.conf
[ 1566.954314] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[ 1566.955548] usbcore: registered new interface driver ndiswrapper
[ 1577.084034] wlan0: no IPv6 routers present

Merci encore...et profitons effectivement un peu de notre dimanche...
hlnrichard

fanfan_85 · Le 28/09/2009, à 00:56

J'ai une autre solution pour toi et on aurait du commencer par ça. Je suis vraiment c**.

Attention: la commande que je vais te donner va désinstaller Network Manager mais c'est normal
Si un jour tu veux remettre network manager, lances la commande suivante:

sudo apt-get install network-manager network-manager-gnome

Maintenant, lances la commande suivante:

sudo apt-get install wicd

Vas dans "Système=>Préférences=>Applications au démarrage" et décoches "Gestionnaire de réseau" (recoches le si tu réinstalles Network Manager)

Rédémarres ton pc

Si wicd (un équivalent de Network Manager) n'est pas lancé à la place de network manager, lances le en allant dans "Applications=>Internet=>Wicd Network Manager"

Dis moi maintenant si wicd voit ton réseau wifi, il fonctionne d'une manière similaire à Network Manager

Pour tes autres questions, je n'ai pas trop d'idées. Tu peux être qu'il y a forcément une équipe Linux pour trouver une solution au problème du driver de ta carte mais ça peut prendre du temps

Par contre, j'ai également remarqué que ton pc a des problèmes de ventilo. C'est aussi un bug ubuntu connu de ce pc. Mais un problème à la fois, on en rediscutera après le problème de wifi

Ciao

Dernière modification par fanfan_85 (Le 28/09/2009, à 01:04)

hlnrichard · Le 28/09/2009, à 09:10

Salut fanfan,

J'ai désinstallé networkmanager mais wicd ne détecte pas mon réseau wifi. L'interface apparaît normalement mais même après plusieurs réactualisations, il reste aveugle...
Peut-être faut-il que je change les préférences ?

Oui, mes ventilos sont capricieux. Un forum a été lancé sur ce sujet mais pour l'instant, je suis à la phase de décryptage des échanges (entre gens plus calés
que moi).
Merci encore et désolé de te donner autant de fil à retordre.
Hlnrichard

fanfan_85 · Le 28/09/2009, à 11:02

Quand tu pourras, donnes moi le retour des commandes suivantes:

sudo iwlist wlan0 scan
sudo iwlist wlan0 scanning

Une des deux commandes va te renvoyer une erreur, c'est normal

hlnrichard · Le 28/09/2009, à 12:13

Voilà le résultat des commandes :

helene@helene-laptop:~$ sudo iwlist wlan0 scan
[sudo] password for helene: 
wlan0     No scan results

helene@helene-laptop:~$ sudo iwlist wlan0 scanning
wlan0     No scan results

Note : je suis connectée à un réseau filaire sur mon lieu de travail. Il y a, ici, également un réseau wifi (accès à partir d'une page web avec login et mot de passe). Je pense que je peux tester les "performances" de ma carte wifi même dans cette situation, n'est-ce pas ? Ou mieux vaut ne pas compliquer les choses ?

hlnrichard

fanfan_85 · Le 28/09/2009, à 13:56

Il ne me reste plus alors qu'une seule solution à te proposer (après je sèche):
c'est la configuration manuelle du wifi

Tout d'abord, j'ai besoin de connaitre ton FAI (Free? Orange? Darty? etc)

[Edit.]: Peux-tu me faire un autre test en meme temps?

lances la commande suivante:

sudo gedit /etc/default/avahi-daemon

à la fin du fichier, ajoutes les 2 lignes suivantes:

AVAHI_DAEMON_START=0
AVAHI_DAEMON_DETECT_LOCAL=1

Sauvegardes (avec Enregistrer, pas Enregistrer sous...), ne vas pas le sauvegarder ailleurs qu'à l'endroit où il est

Rebootes et regardes si le wifi marche avec Wicd (que je t'ai fait installer la dernière fois)

Si ca marche pas aussi, essayes la commande suivante:

sudo /etc/init.d/networking restart

Et si ca ne marche toujours pas, renvoies moi en plus de ton FAI, le retour des commandes suivantes:

ifconfig
iwconfig

Ca commence à devenir long tout ça, heureusement que t'as de la patience

Dernière modification par fanfan_85 (Le 28/09/2009, à 14:18)

hlnrichard · Le 28/09/2009, à 14:14

Mon FAI est Alice

fanfan_85 · Le 28/09/2009, à 14:17

regarde le Edit de mon post precedent stp

hlnrichard · Le 28/09/2009, à 14:39

Patience, oui... toi aussi tu en as beaucoup !

Ca ne marche pas non plus.
Pour sudo /etc/init.d/networking restart, j'ai reçu :

 * Reconfiguring network interfaces...                                          Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

Listening on LPF/wlan0/00:24:d2:df:ad:0a
Sending on   LPF/wlan0/00:24:d2:df:ad:0a
Sending on   Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 16
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 3
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
                                                                         [ OK ]

Pour le reste :

eth0      Link encap:Ethernet  HWaddr 00:26:18:85:c0:12  
          inet adr:10.6.158.185  Bcast:10.6.255.255  Masque:255.255.0.0
          adr inet6: fe80::226:18ff:fe85:c012/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          Packets reçus:26144 erreurs:0 :0 overruns:0 frame:0
          TX packets:135 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          Octets reçus:1662628 (1.6 MB) Octets transmis:22086 (22.0 KB)
          Interruption:250 Adresse de base:0xa000 

lo        Link encap:Boucle locale  
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          Packets reçus:4 erreurs:0 :0 overruns:0 frame:0
          TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:0 
          Octets reçus:240 (240.0 B) Octets transmis:240 (240.0 B)

wlan0     Link encap:Ethernet  HWaddr 00:24:d2:df:ad:0a  
          adr inet6: fe80::224:d2ff:fedf:ad0a/64 Scope:Lien
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
          Interruption:17 Mémoire:fdffc000-fe000000

helene@helene-laptop:~$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:off/any  
          Mode:Managed  Frequency:2.457 GHz  Access Point: Not-Associated   
          Bit Rate:130 Mb/s   Tx-Power:20 dBm   Sensitivity=0/3  
          RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

pan0      no wireless extensions.

fanfan_85 · Le 28/09/2009, à 15:08

ce qu'il faudrait, c'est que tu me donnes le nom (essid) de ta box et à partir de là, je te donnerai (ce soir) la configuration à faire. Il ne devrait plus y a voir grand chose à faire normalement.

PS: Le nom de ta box marqué quelque part sur ta box et elle commence par ALICE-... (fais bien attention à la casse du nom stp)

hlnrichard · Le 29/09/2009, à 09:57

Hier soir, je n'ai pas eu le temps de me connecter. Désolé. Je te donne l'Essid ce soir à partir de 20h30.

hlnrichard

hlnrichard · Le 29/09/2009, à 15:19

Bonjour fanfan_85,

Mon ESSID est Alice-7f84

Mais en tapant la commande cat /etc/network/interfaces, j'obtiens :

cat /etc/network/interfaces
auto lo
iface lo inet loopback



iface wlan0 inet dhcp
wireless-key ***********************
wireless-essid Alice-7f84

Or, j'avais changé mon mot de passe WEP par un mot de passe WPA (on essaye tout dans mon cas !), l'ordinateur ne semble pas avoir pris en compte ce changement. Le problème vient peut-être de là ?

hlnrichard

Dernière modification par hlnrichard (Le 29/09/2009, à 22:40)

hlnrichard · Le 29/09/2009, à 18:30

Du nouveau !
Un ami m'a proposé de faire cette manip :

sudo gedit /etc/network/interfaces

Et remplace iface wlan0 inet dhcp

par:

iface wlan0 inet static
address 192.168.1.3
netmask 255.255.255.0
gateway 192.168.1.1

J'ai alors tapé :

sudo /etc/init.d/networking restart

Normalement, m'a-t-il dit, je devais être automatiquement connectée au wifi. Ce n'était pas le cas mais MIRACLE, wicd a repéré mon réseau wifi.

J'ai cliqué sur "se connecter" en dessous de l'icone de mon réseau. Sans résultat. Je suis allée voir dans les paramètres où j'ai remarqué des correspondances avec les lignes de code que m'avait donné mon ami :
1) Utiliser des adresses IP statiques ---> j'ai coché
a) juste en dessous : IP = j'ai noté "192.168.1.3"
b) il m'a alors complété automatiquement le netmask (masque de réseau) et le gateway (passerelle)
2) Utiliser un DSN Statique : je n'ai pas coché. On me propose éventuellement d'utiliser les DNS globaux. En cochant cette case, s'affiche le message suivant : Global DNS is not enabled in preferences, so it can't be used for this network
3) Utiliser ces paramètres pour tous les réseaux partageant cet ESSID : je n'ai pas coché
4) Utiliser le chiffrement : j'ai coché. Puis j'ai sélectionné dans le menu déroulant "WEP Hex" et noté ma clé WEP.

En voulant valider, un message s'affiche : "Invalid address in DNS 1 entry"

Je suis près du but quand même, n'est-ce pas ?

fanfan_85 · Le 29/09/2009, à 21:40

Je ne vois pas quelle erreur ça peut etre mais effectivement, il y a du mieux. Je suis en train de regarder ce qu'il doit te manquer. Patientes un peu encore, tu es près du but.

PS: cette ligne que tu as mises 2 messages avant, c'est ton mot de passe personnel pour ton wifi, il vaudrait mieux que la remplaces par:

wireless-key xxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Utilises "Modifier" dans le forum pour corriger ça

fanfan_85 · Le 29/09/2009, à 21:50

Voila, quand tu mets les "Paramètres avancés", tu dois paramétrer de la meme manière qu'à ce lien:
http://img121.imageshack.us/img121/3227 … avancs.png

Bien sur, dans "key", tu mets la clé wep de ta box

Et dans le cas d'une clé wpa, tes "Paramètres avancés" doivent ressembler à ceci:
http://img524.imageshack.us/img524/6010 … vancs1.png
Sauf que cette fois, tu mets ta clé wpa dans "key"

Essayes et dis moi

Dernière modification par fanfan_85 (Le 29/09/2009, à 22:12)

hlnrichard · Le 29/09/2009, à 22:43

Bonsoir fanfan !
Wicd m'indique : connecté à Alice 7f-84 mais les pages ne se chargent pas...
Décidément, ça sera jusqu'au bout...

fanfan_85 · Le 29/09/2009, à 22:47

donnes moi le resultat de :

ping google.com

Pour arreter cette commande, il faut appuyer sur Ctrl+c

hlnrichard · Le 29/09/2009, à 22:52

ping google.com donne :

64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=1 ttl=53 time=138 ms
64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=2 ttl=53 time=139 ms
64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=3 ttl=53 time=136 ms
64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=4 ttl=53 time=137 ms
64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=5 ttl=53 time=137 ms
64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=6 ttl=53 time=137 ms
64 bytes from yx-in-f100.google.com (74.125.45.100): icmp_seq=7 ttl=53 time=137 ms

etc., etc. etc.

fanfan_85 · Le 29/09/2009, à 22:55

Ok, Piece of cake

débranches ton cable ethernet, fermes firefox, reconnectes toi en wifi, ouvres firefox

hlnrichard · Le 29/09/2009, à 23:02

Je ne comprends pas : WICD m'indique que je suis connectée à Alice à 50% mais les pages ne se chargent pas.

fanfan_85 · Le 29/09/2009, à 23:04

qu'y a-t-il marqué sur firefox?

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#26 Le 27/09/2009, à 16:20

Re : Toshiba U500 - bon driver mais wifi non géré

#27 Le 27/09/2009, à 16:34

Re : Toshiba U500 - bon driver mais wifi non géré

#28 Le 27/09/2009, à 16:47

Re : Toshiba U500 - bon driver mais wifi non géré

#29 Le 27/09/2009, à 16:51

Re : Toshiba U500 - bon driver mais wifi non géré

#30 Le 27/09/2009, à 17:00

Re : Toshiba U500 - bon driver mais wifi non géré

#31 Le 28/09/2009, à 00:56

Re : Toshiba U500 - bon driver mais wifi non géré

#32 Le 28/09/2009, à 09:10

Re : Toshiba U500 - bon driver mais wifi non géré

#33 Le 28/09/2009, à 11:02

Re : Toshiba U500 - bon driver mais wifi non géré

#34 Le 28/09/2009, à 12:13

Re : Toshiba U500 - bon driver mais wifi non géré

#35 Le 28/09/2009, à 13:56

Re : Toshiba U500 - bon driver mais wifi non géré

#36 Le 28/09/2009, à 14:14

Re : Toshiba U500 - bon driver mais wifi non géré

#37 Le 28/09/2009, à 14:17

Re : Toshiba U500 - bon driver mais wifi non géré

#38 Le 28/09/2009, à 14:39

Re : Toshiba U500 - bon driver mais wifi non géré

#39 Le 28/09/2009, à 15:08

Re : Toshiba U500 - bon driver mais wifi non géré

#40 Le 29/09/2009, à 09:57

Re : Toshiba U500 - bon driver mais wifi non géré

#41 Le 29/09/2009, à 15:19

Re : Toshiba U500 - bon driver mais wifi non géré

#42 Le 29/09/2009, à 18:30

Re : Toshiba U500 - bon driver mais wifi non géré

#43 Le 29/09/2009, à 21:40

Re : Toshiba U500 - bon driver mais wifi non géré

#44 Le 29/09/2009, à 21:50

Re : Toshiba U500 - bon driver mais wifi non géré

#45 Le 29/09/2009, à 22:43

Re : Toshiba U500 - bon driver mais wifi non géré

#46 Le 29/09/2009, à 22:47

Re : Toshiba U500 - bon driver mais wifi non géré

#47 Le 29/09/2009, à 22:52

Re : Toshiba U500 - bon driver mais wifi non géré

#48 Le 29/09/2009, à 22:55

Re : Toshiba U500 - bon driver mais wifi non géré

#49 Le 29/09/2009, à 23:02

Re : Toshiba U500 - bon driver mais wifi non géré

#50 Le 29/09/2009, à 23:04

Re : Toshiba U500 - bon driver mais wifi non géré

Pied de page des forums