éternel problème avec netgear wg111t et WIFI par adaptteur USB

monsanto · Le 26/09/2009, à 11:35

J'essaie de connecter ce pc au net par clé wifi netgear wg111T

J'ai suivi les recommandations et vous poste toute information utile :

monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ ndiswrapper -l
netwg11t : driver installed
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ lsusb
Bus 002 Device 002: ID 1385:4251 Netgear, Inc WG111T (no firmware)
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 046d:c016 Logitech, Inc. M-UV69a/HP M-UV96 Optical Wheel Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=9.04
DISTRIB_CODENAME=jaunty
DISTRIB_DESCRIPTION="Ubuntu 9.04"
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ lspci
00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP78S [GeForce 8200] LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP78S [GeForce 8200] SMBus (rev a1)
00:01.2 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a1)
00:01.3 Co-processor: nVidia Corporation MCP78S [GeForce 8200] Co-Processor (rev a2)
00:01.4 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a1)
00:02.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller (rev a1)
00:04.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller (rev a1)
00:04.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller (rev a1)
00:06.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] IDE (rev a1)
00:07.0 Audio device: nVidia Corporation MCP78S [GeForce 8200] High Definition Audio (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1)
00:09.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] SATA Controller (non-AHCI mode) (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation MCP78S [GeForce 8200] Ethernet (rev a2)
00:0b.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1)
00:10.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1)
00:12.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1)
00:13.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1)
00:14.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:09.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
01:0a.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70)
02:00.0 VGA compatible controller: nVidia Corporation GeForce 8300 (rev a2)
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ sudo lshw -C network
*-network
description: Ethernet interface
product: MCP78S [GeForce 8200] Ethernet
vendor: nVidia Corporation
physical id: a
bus info: pci@0000:00:0a.0
logical name: eth0
version: a2
serial: 00:23:54:3a:07:fe
size: 100MB/s
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm msi ht bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=forcedeth driverversion=0.61 duplex=full ip=192.168.0.3 latency=0 link=yes maxlatency=20 mingnt=1 module=forcedeth multicast=yes port=MII speed=100MB/s
*-network:0 DISABLED
description: Ethernet interface
physical id: 1
logical name: pan0
serial: 82:56:35:eb:90:dd
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
*-network:1 DISABLED
description: Ethernet interface
physical id: 2
logical name: vboxnet0
serial: 0a:00:27:00:00:00
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ lsmod
Module Size Used by
vboxnetadp 90216 0
vboxnetflt 97032 0
vboxdrv 132008 1 vboxnetflt
binfmt_misc 16776 1
ppdev 15620 0
bridge 56212 0
stp 10500 1 bridge
bnep 20224 2
input_polldev 11912 0
video 25360 0
output 11008 1 video
lp 17156 0
parport 42220 2 ppdev,lp
snd_cmipci 42016 2
gameport 19468 1 snd_cmipci
snd_opl3_lib 18560 1 snd_cmipci
snd_hwdep 15108 1 snd_opl3_lib
snd_mpu401_uart 15104 1 snd_cmipci
snd_seq_dummy 10756 0
snd_seq_oss 37760 0
snd_hda_intel 434100 2
snd_seq_midi 14336 0
snd_pcm_oss 46336 0
snd_rawmidi 29696 2 snd_mpu401_uart,snd_seq_midi
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
nvidia 7233756 36
snd_mixer_oss 22656 1 snd_pcm_oss
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_pcm 83076 3 snd_cmipci,snd_hda_intel,snd_pcm_oss
snd_seq_device 14988 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
agpgart 42696 1 nvidia
snd_timer 29704 3 snd_opl3_lib,snd_seq,snd_pcm
snd 62756 21 snd_cmipci,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_seq_oss,snd_hda_intel,snd_pcm_oss,snd_rawmidi,snd_mixer_oss,snd_seq,snd_pcm,snd_seq_device,snd_timer
snd_page_alloc 16904 2 snd_hda_intel,snd_pcm
soundcore 15200 1 snd
k8temp 12416 0
shpchp 40212 0
pcspkr 10496 0
usbhid 42336 0
ohci1394 38576 0
forcedeth 61712 0
ieee1394 94660 1 ohci1394
floppy 64324 0
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.

vboxnet0 no wireless extensions.

monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:23:54:3a:07:fe
inet adr:192.168.0.3 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::223:54ff:fe3a:7fe/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:78858 erreurs:0 :0 overruns:0 frame:0
TX packets:50512 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:114041560 (114.0 MB) Octets transmis:4160473 (4.1 MB)
Interruption:250

lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)

monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ sudo iwlist scan
lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

pan0 Interface doesn't support scanning.

vboxnet0 Interface doesn't support scanning.

monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ cat /etc/network/interfaces
auto lo
iface lo inet loopback

monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ nm-tool

NetworkManager Tool

State: connected

- Device: eth0 [Auto eth0] ----------------------------------------------------
Type: Wired
Driver: forcedeth
State: connected
Default: yes
HW Address: 00:23:54:3A:07:FE

Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s

Wired Properties
Carrier: on

IPv4 Settings:
Address: 192.168.0.3
Prefix: 24 (255.255.255.0)
Gateway: 192.168.0.254

DNS: 212.27.40.241
DNS: 212.27.40.240

monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$ uname -r -m
2.6.28-15-generic i686
monsanto@monsanto:~/rtl8187/rtl8187_linux_26.1010.0622.2006$

=============

ndiswrapper a l'air bien installé, me dit que WG11T est bien installé, mais lsusb me répond "no firmware" ... la clé se clignote pas, rien dans network manager, uniquement la connection ETH0 , wlan0 :

sudo ifconfig wlan0 down
wlan0: ERREUR en récupérant les signaux de l'interface: Aucun périphérique de ce type

merci à tous ceux qui m'aideront à avancer .

sous windows, dans les propriétés du périhpérique j'obtiens 1385 - 4251, ce qui est censé indiquer un chipset usb atheros et un pilote madwifi .... et d'après le site http://linux-wless.passys.nl/query_part?brandname=Netgear
cela ne "fonctionne pas"

... toute aide bienvenue

toutafai · Le 26/09/2009, à 14:25

bonjour,

ndiswrapper est peut etre installé, mais pas configuré (il n'apparait pas sur le retour du "lsmod", et rien non plus dans le retour du "sudo lshw -C network")

tente ca (donne les retours)

sudo -s 
ndiswrapper -m
modprobe ndiswrapper
lshw -C network
ifconfig -a
iwconfig
iwlist scan
exit

monsanto · Le 26/09/2009, à 14:41

enfait, j'ai suivi ceci

http://ubuntuforums.org/showthread.php?t=258732&page=2

je me retrouve avec la clé usb clignotante, network manager me reconnait les réseaux ... mais il m'affiche réseau sans fil déconnecté...

si j'ôte le port éthernet, peut-être un conflit me dis-(je, rien de mieux . j'ai pu observer une fenêtre sur le pc qui tourne en meme temps sous windows conflit d'ips mais le problème n'est pas là je pense, il me demande toutes les deux minutes "mot de passe pour le réseau sans fil" mais ne se connecte toujours pas -_-

j'ai tapé les commandes que tu as donné

monsanto@monsanto:~/Bureau/c$ sudo -s
[sudo] password for monsanto:
root@monsanto:~/Bureau/c# ndiswrapper -m
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
module configuration already contains alias directive

module configuration already contains alias directive

root@monsanto:~/Bureau/c# modprobe ndiswrapper
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
root@monsanto:~/Bureau/c# lshw -C network
*-network
description: Ethernet interface
product: MCP78S [GeForce 8200] Ethernet
vendor: nVidia Corporation
physical id: a
bus info: pci@0000:00:0a.0
logical name: eth0
version: a2
serial: 00:23:54:3a:07:fe
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm msi ht bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=forcedeth driverversion=0.61 latency=0 link=no maxlatency=20 mingnt=1 module=forcedeth multicast=yes port=MII
*-network:0 DISABLED
description: Ethernet interface
physical id: 1
logical name: vboxnet0
serial: 0a:00:27:00:00:00
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:1 DISABLED
description: Ethernet interface
physical id: 2
logical name: pan0
serial: f6:b0:14:9e:50:86
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
*-network:2
description: Wireless interface
physical id: 3
logical name: wlan0
serial: 00:14:6c:57:31:47
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=ndiswrapper+netwg11t driverversion=1.53+NETGEAR,10/15/2004,1.0.1.10 link=no multicast=yes wireless=IEEE 802.11g
root@monsanto:~/Bureau/c# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:23:54:3a:07:fe
adr inet6: fe80::223:54ff:fe3a:7fe/64 Scope:Lien
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:4314 erreurs:0 :0 overruns:0 frame:0
TX packets:3084 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:5556237 (5.5 MB) Octets transmis:362787 (362.7 KB)
Interruption:250

lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:424 erreurs:0 :0 overruns:0 frame:0
TX packets:424 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:32368 (32.3 KB) Octets transmis:32368 (32.3 KB)

pan0 Link encap:Ethernet HWaddr f6:b0:14:9e:50:86
BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)

vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)

wlan0 Link encap:Ethernet HWaddr 00:14:6c:57:31:47
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)

root@monsanto:~/Bureau/c# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

vboxnet0 no wireless extensions.

pan0 no wireless extensions.

wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:11 Mb/s
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

root@monsanto:~/Bureau/c# iwlist scan
lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

vboxnet0 Interface doesn't support scanning.

pan0 Interface doesn't support scanning.

wlan0 Scan completed :
Cell 01 - Address: 92:A3:6B:3B:3A:49
ESSID:""
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:90/100 Signal level:-38 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0

root@monsanto:~/Bureau/c#

maintenant, à part que je viens d'apprendre comment me délogguer et que l'icone network manager ne "tourne/cherche plus" mais affiche la croix qui dit "pas connecté", ntework manager ne détecte plus de réseau sans fil::

toutafai · Le 26/09/2009, à 19:13

ok, on avance puisque ton wifi est desormais "piloté" par ndiswrapper comme l'indique le "lshw -C network" et le module ndiswrapper est bien chargé comme le montre le retour du "lsmod"...maintenand y a encore un probleme avec network manager, on va s'en occuper...donne le retour de

cat /etc/network/interfaces
cat /etc/modules # pour voir si il y a bien une ligne contenant "ndiswrapper" (sans les apostrophes bien sur)

Dernière modification par toutafai (Le 26/09/2009, à 19:13)

monsanto · Le 12/11/2009, à 22:55

ca me donne ca
monsanto@monsanto:~$ cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp
ndiswrapper

??

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 26/09/2009, à 11:35

éternel problème avec netgear wg111t et WIFI par adaptteur USB

#2 Le 26/09/2009, à 14:25

Re : éternel problème avec netgear wg111t et WIFI par adaptteur USB

#3 Le 26/09/2009, à 14:41

Re : éternel problème avec netgear wg111t et WIFI par adaptteur USB

#4 Le 26/09/2009, à 19:13

Re : éternel problème avec netgear wg111t et WIFI par adaptteur USB

#5 Le 12/11/2009, à 22:55

Re : éternel problème avec netgear wg111t et WIFI par adaptteur USB

Pied de page des forums