Ubuntu-fr

webuntu

Pb hylafax: Failure to train modems

j'ai un problème de réception de fax de quelques clients, où je ne peut pas réceptionné aucun fax
J'ai essayer de changer le class1 par class1.0 mais le problème persiste.
aider moi svp.

LOG :

sep 29 10:02:29.25: [  691]: SESSION BEGIN 000000487 XXXXXXXXXX
sep 29 10:02:29.25: [  691]: HylaFAX (tm) Version 4.4.3
sep 29 10:02:29.25: [  691]: DynamicConfig: bin/dynconf.php "/dev/ttyACM1"
sep 29 10:02:29.29: [  691]: <-- [4:ATA\r]
sep 29 10:02:34.97: [  691]: --> [7:CONNECT]
sep 29 10:02:34.97: [  691]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyACM1'
sep 29 10:02:34.97: [  691]: RECV FAX: begin
sep 29 10:02:34.97: [  691]: <-- data [32]
sep 29 10:02:34.97: [  691]: <-- data [2]
sep 29 10:02:37.79: [  691]: --> [7:CONNECT]
sep 29 10:02:37.79: [  691]: <-- data [23]
sep 29 10:02:37.79: [  691]: <-- data [2]
sep 29 10:02:38.56: [  691]: --> [7:CONNECT]
sep 29 10:02:38.56: [  691]: <-- data [13]
sep 29 10:02:38.56: [  691]: <-- data [2]
sep 29 10:02:39.62: [  691]: --> [2:OK]
sep 29 10:02:39.62: [  691]: <-- [9:AT+FRH=3\r]
sep 29 10:02:40.10: [  691]: --> [7:CONNECT]
sep 29 10:02:41.93: [  691]: --> [2:OK]
sep 29 10:02:41.93: [  691]: REMOTE TSI ""
sep 29 10:02:41.93: [  691]: RECV recv TSI (sender id)
sep 29 10:02:41.93: [  691]: <-- [9:AT+FRH=3\r]
sep 29 10:02:41.94: [  691]: --> [7:CONNECT]
sep 29 10:02:41.94: [  691]: --> [2:OK]
sep 29 10:02:41.94: [  691]: REMOTE wants 9600 bit/s
sep 29 10:02:41.94: [  691]: REMOTE wants A4 page width (215 mm)
sep 29 10:02:41.94: [  691]: REMOTE wants unlimited page length
sep 29 10:02:41.94: [  691]: REMOTE wants 3.85 line/mm
sep 29 10:02:41.94: [  691]: REMOTE wants 1-D MH
sep 29 10:02:41.94: [  691]: RECV recv DCS (command signal)
sep 29 10:02:41.94: [  691]: RECV training at v.29 9600 bit/s
sep 29 10:02:41.94: [  691]: <-- [10:AT+FRM=96\r]
sep 29 10:02:46.44: [  691]: --> [0:]
sep 29 10:02:46.44: [  691]: MODEM <Empty line>
sep 29 10:02:46.44: [  691]: <-- data [1]
sep 29 10:02:46.45: [  691]: --> [2:OK]
sep 29 10:02:46.45: [  691]: <-- [9:AT+FRS=7\r]
sep 29 10:02:46.58: [  691]: --> [2:OK]
sep 29 10:02:46.58: [  691]: <-- [9:AT+FTH=3\r]
sep 29 10:02:46.63: [  691]: --> [7:CONNECT]
sep 29 10:02:46.63: [  691]: <-- data [3]
sep 29 10:02:46.63: [  691]: <-- data [2]
sep 29 10:02:47.94: [  691]: --> [2:OK]
sep 29 10:02:47.94: [  691]: TRAINING failed
sep 29 10:02:47.94: [  691]: <-- [9:AT+FRH=3\r]
sep 29 10:02:54.00: [  691]: --> [7:CONNECT]
sep 29 10:02:55.94: [  691]: --> [2:OK]
sep 29 10:02:55.94: [  691]: REMOTE TSI ""
sep 29 10:02:55.94: [  691]: RECV recv TSI (sender id)
sep 29 10:02:55.94: [  691]: <-- [9:AT+FRH=3\r]
sep 29 10:02:55.95: [  691]: --> [7:CONNECT]
sep 29 10:02:55.95: [  691]: --> [2:OK]
sep 29 10:02:55.95: [  691]: REMOTE wants 9600 bit/s
sep 29 10:02:55.95: [  691]: REMOTE wants A4 page width (215 mm)
sep 29 10:02:55.95: [  691]: REMOTE wants unlimited page length
sep 29 10:02:55.95: [  691]: REMOTE wants 3.85 line/mm
sep 29 10:02:55.95: [  691]: REMOTE wants 1-D MH
sep 29 10:02:55.95: [  691]: RECV recv DCS (command signal)
sep 29 10:02:55.95: [  691]: RECV training at v.29 9600 bit/s
sep 29 10:02:55.95: [  691]: <-- [10:AT+FRM=96\r]
sep 29 10:03:00.45: [  691]: --> [0:]
sep 29 10:03:00.45: [  691]: MODEM <Empty line>
sep 29 10:03:00.45: [  691]: <-- data [1]
sep 29 10:03:00.46: [  691]: --> [2:OK]
sep 29 10:03:00.46: [  691]: <-- [9:AT+FRS=7\r]
sep 29 10:03:00.59: [  691]: --> [2:OK]
sep 29 10:03:00.59: [  691]: <-- [9:AT+FTH=3\r]
sep 29 10:03:00.64: [  691]: --> [7:CONNECT]
sep 29 10:03:00.64: [  691]: <-- data [3]
sep 29 10:03:00.64: [  691]: <-- data [2]
sep 29 10:03:01.96: [  691]: --> [2:OK]
sep 29 10:03:01.96: [  691]: TRAINING failed
sep 29 10:03:01.96: [  691]: <-- [9:AT+FRH=3\r]
sep 29 10:03:08.96: [  691]: --> [0:]
sep 29 10:03:08.96: [  691]: MODEM <Empty line>
sep 29 10:03:08.96: [  691]: <-- data [1]
sep 29 10:03:09.01: [  691]: --> [2:OK]
sep 29 10:03:09.01: [  691]: <-- [9:AT+FRS=7\r]
sep 29 10:03:09.14: [  691]: --> [2:OK]
sep 29 10:03:09.14: [  691]: <-- [9:AT+FTH=3\r]
sep 29 10:03:09.17: [  691]: --> [7:CONNECT]
sep 29 10:03:09.17: [  691]: <-- data [32]
sep 29 10:03:09.17: [  691]: <-- data [2]
sep 29 10:03:10.72: [  691]: --> [7:CONNECT]
sep 29 10:03:10.72: [  691]: <-- data [23]
sep 29 10:03:10.72: [  691]: <-- data [2]
sep 29 10:03:11.49: [  691]: --> [7:CONNECT]
sep 29 10:03:11.49: [  691]: <-- data [13]
sep 29 10:03:11.49: [  691]: <-- data [2]
sep 29 10:03:12.55: [  691]: --> [2:OK]
sep 29 10:03:12.55: [  691]: <-- [9:AT+FRH=3\r]
sep 29 10:03:19.55: [  691]: --> [0:]
sep 29 10:03:19.55: [  691]: MODEM <Empty line>
sep 29 10:03:19.55: [  691]: <-- data [1]
sep 29 10:03:19.60: [  691]: --> [2:OK]
sep 29 10:03:19.60: [  691]: RECV FAX: Failure to train modems
sep 29 10:03:19.60: [  691]: RECV FAX: end
sep 29 10:03:19.60: [  691]: Failure to train modems
sep 29 10:03:19.60: [  691]: SESSION END

config.ttyACM1 :

CountryCode:            216
AreaCode:               216
FAXNumber:              +216.XXXXXXX
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0664
LogFileMode:            0664
DeviceMode:             0666
RingsBeforeAnswer:      2
SpeakerVolume:          high
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        XXXX
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
PercentGoodLines:       90
MaxRecvPages:           25
NotifyCmd:              bin/notify.php
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1.0        # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # default
#
# With the RocketModem IV (and possibly III) you may need to use a much
# higher ModemRate than 19200 because, apparently, it suffers from potential
# buffer underrun problems.  Fortunately, it doesn't have buffer overflow
# issues, and so using 115200 should work (both rtscts and xonxoff test good).
#
ModemNoFlowCmd:         AT&K0           # setup no flow control
ModemHardFlowCmd:       AT&K3           # setup hardware flow control
ModemSoftFlowCmd:       AT&K4           # setup software flow control
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
#
Class1AdaptRecvCmd:     AT+FAR=1        # reports carrier detection mismatches

#
#### AvantFAX
###
FaxRcvdCmd:     bin/faxrcvd.php
DynamicConfig:  bin/dynconf.php
UseJobTSI:      true

Merci d'avance